Search Documents

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By Milton C. Graves, Marcos Zentilli

"Gold has been reported from most geological environments in Nova Scotia; however, virtually all production (circa 2,000, 000 troy ounces; circa 60 tonnes) has come from that part of the province to the south of the Glooscap Fault which is underlain by Lower Paleozoic rocks of the Meguma Group. Over fifty concordant sets of quartz-carbonate-arsenopyrite veins have seen production. The host rocks are greenschist-grade equivalents of Cambro-Ordovician flyschoid quartz wackes and shales folded and metamorphosed during the Devonian Acadian Orogeny. The veins were emplaced under conditions of greenschist-grade regional metamorphism and under the same conditions of tectonic stress that later resulted in the regional folds and penetrative, axial-plane slaty cleavage. Rapid filling of hydraulic fractures caused by excess metamorphic pore fluid pressure under Acadian tectonic stress conditions can account for the geometry and paragenesis of these veins.The ultimate source for gold deposits in most greenschist-grade domains remains in doubt, but these domains seem to have had ample gold within them available for mobilization. The work done, to date, on the gold geology of Nova Scotia suggests that regional greenschist metamorphism was an effective mobilizer and a potential concentrator of Au, As, W, Fe and S from these vast reservoirs.In rocks of pre-Acadian age north of the Glooscap Fault, gold occurs as an important accessory in volcanogenic massive sulphide ore, as a minor constituent in other types of basemetal concentrations and in one small concordant group of quartz veins.The post-Acadian metallogenetic domain, which overlies and overprints the two older domains, contains small amounts of gold in many mineralizing environments. Veins, with stibnite and gold, cross-cut crystalline rocks. Disseminated gold is present in basal conglomerates of post-tectonic molasse. Gold has been a by-product of Mississippi Valley-type Pb-Zn-Ba-Sr deposits in Lower Carboniferous sedimentary rocks and has been reported with Pb-Zn-Ba-F in veins which cross-cut Lower Carboniferous and older rocks. Small post-glacial placers have also seen minor production."

Jan 1, 1982

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By G. Paquet, E. Godin

"Since the mid fifty's, worlwide pellet production capacity has constantly risen (Fig. 1, Ref. 1 l. There was however at that time no real incentive to decrease production costs but only to produce as many pellets as possible. State of things changed with the iron and steel market recession, starting in 1975, and is currently leading producers to improve pellet quality and to reduce fuel and power consumption.At the Port-Cartier pellet plant, the energy needed for the induration of pellets ranks first in overall operating costs. An important step was made when starting admixing coke breeze in 1980. Oil prices justified the use of coke breeze as a direct replacement in terms of dollar/ton, however, while gaining expertise in using solid fuel a significant decrease in energy consumption was observed (Fig. 2, Ref. 2).In 1985, the ""Centre de Recherches minérales"" was commissioned to undertake research work to investigate the effects of further increasing coke addition to the pellet mix. The positive results of that work led to a 1,5% coke addition plant trial during the fall of 1985. Both laboratory and industrial results are discussed in this paper."

Jan 1, 1986

By Gérald Riverin, Bernard Salmon, Marlo Gagnon, Réemi Asselin, Alain Cazavant, Michel LaBrie

"The Ansil deposit is located in the Noranda mining camp in the southern part of the Abitibi greenstone belt. /twas discovered in 1981 and production began in 1989 with proven reserves of 1.58 Mt grading 7.2% copper, 0.9% zinc, 26.5 glt of silver and 1.6 glt of gold. It is centered at a depth of 1.3 kilometre and represents one of the deepest ore discoveries ever made from surface.The deposit consists of a single massive sulphide lens located at the contact between the Northwest Rhyolite and the Rusty Ridge Andesite. The lens strikes north-south and dips 50° east. The thickness of the lens may reach up to 35 m and can change very abruptly both along strike and along dip. The maximum thicknesses of the sulphide lens are reached in its upper (western) and at its lower (eastern) edges, thus giving the deposit its present shape of two sulphide domes connected by a thinner central portion. The lower dome is underlain by a thick accumulation of massive magnetite which may reach 10 to 15m in thickness. The upper and lower domes are underlain by two distinct pipe-shaped zones of stringer and disseminated sulphides which merge with a larger stringer zone at depth.The Ansi/ deposit displays strong relationships between its morphology and the distribution of metals. Hydrothermal alteration consists of chloritization and sericitization. Chlorite alteration is closely associated with stringer sulphide mineralization while sericite is developed in diffuse zones bordering the chloritic zones. Unlike other similar deposits, the Ansil deposit is characterized by very extensive alteration and sulphide mineralization in the hangingwall of the massive sulphides. Several features of the deposit are consistent with an origin from a submarine hydrothermal system which was particularly long-lived, and which thus promoted the build-up of very high fluid temperatures with extensive replacement (and enrichment) of pre-existing sulphides after their original deposition onto the seafloor."

Jan 1, 1990

By C. J. A. Davie

"SUMMARY A practical application of nitric acid oxidation of sulphides, based on the principles of the Arseno process, has been developed for the Cinola ore. Development of the process has been based on testwork conducted by Bacon Donaldson of Vancouver and Hazen Research of Denver, and on conceptual engineering performed by Minproc Engineers of Denver.A comprehensive Stage II report for the project has been submitted to the B.C. permitting agencies, containing provisions for a zero discharge tailings impoundment system and prevention of acid mine drainage. Approval in principle is expected in early 1989.A feasibility study recently completed by Minproc Engineers and Davy McKee Corporation demonstrates that this project can be brought to production for a capital expenditure of C$120 million for a mill throughput of 6,000 tonnes/day and operated at a total direct operating cost of less than $20/tonne.INTRODUCTION The Cinola orebody was discovered in 1970. It is situated approximately in the centre of Graham Island, the largest of the Queen Charlotte Islands. It represents the mid to upper levels of a hydrothermal precious metals system, characterized by intense brecciation and silicification. Gold is associated with finely disseminated sulphides in a breccia matrix and in free form in numerous quartz veins.Ownership of the property has changed hands a number of times, and previous attempts to bring the property to production have failed. Two critical factors have frequently been blamed for difficulty in creating a successful project: namely, process and environment factors, hence the title of this paper.City Resources (Canada) Limited (""City"") acquired the property in 1986, and commenced an aggressive campaign to verify ore reserves, to carry out metallurgical research and to address environmental issues.PROJECT OVERVIEW When the Cinola orebody was discovered, the significance of hydrothermal mineraliza¬tion associated with crustal plate boundaries was not recognized, and for several years, the orebody was considered an uneconomic curiosity. If the type and location of orebody sought by many companies engaged in gold exploration were to be specified, it would probably be a description of the Cinola orebody - it is a large (greater than 1.5 million ounce), low grade (2.45 gm/tonne), refractory ore reserve associated with the Pacific rim crustal plate boundary. The industry appears to have recognized in the past few years that its future lies in the exploitation of such orebodies, and is prepared to come to grips with the technical problems associated with such ores. In this sense, the Cinola orebody might be considered to have come of age."

Jan 1, 1989

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By P. R. Richardson

"Milling is the weak link in the process chain of many mineral operations. While this activity accounts for only a relatively small proportion of the direct costs of most mineral processing complexes, there are intangible and indirect costs associated with milling which are extremely large. For example, significant opportunity costs are associated with the relatively low yields which characterize this stage of the process.There are changes abroad in the world which I believe are going to cause us to reformulate the whole concept of milling. Increased competition in mineral markets are going to force managers to look anew at the high mineral values reporting to tailings which are a high opportunity cost for many operations. Tailings recovery plants are not the ultimate solution to this problem. Greater environmental concerns are going to increase the costs associated with tailings disposal and force the mining industry to look for other ways to dispose of waste products. Technology changes currently underway in manufacturing and other process industries, such as the automated 'lights-out' plant are going to be brought into this industry, and the changes will be dramatic.These are major long term changes which probably seem rather remote to many managers and professionals in existing operations which are faced with much more mundane challenges arising from day-to-day operations. However, I believe that milling is increasingly a 'lean and keen' operation involving fewer and fewer people, but who are increasingly skilled and professional. Traditional cost management approaches are no longer adequate and the industry has to take a new look at the nature of cost reduction in this core activity. This stage in the mineral process provides opportunities for value creation leading to a significant unit cost advantage for the corporations willing to adopt a total cost approach."

Jan 1, 1988

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011