Search Documents

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

By D Reid, A Fourie

The in-pipe treatment of slurries with polymer addition shortly prior to deposition is a noteworthy emerging technology of increasing popularity. Although polymer treatment has been shown to substantially modify and improve depositional and dewatering behaviour in a significant number of cases, the impacts of polymer treatment on geotechnical performance of tailings are less well understood. For example, certain combinations of polymer and slurry type have been shown to result in lower final densities at a given vertical effective stress. Despite these lower densities, polymer-treated tailings often exhibit peak undrained shear strengths consistent with untreated material. However, the sensitivity and/or brittleness of the material may be negatively influenced by the looser state created. Although these changes have been studied, most testing available in the literature was undertaken on relatively ‘fresh’ samples of polymer-treated material. However, significant shear may occur following treatment and prior to the commencement of settling and self-weight consolidation as the material moves down the beach.To study the effects of shearing on the subsequent performance of polymer-treated tailings, a test program consisting of consolidation, triaxial and direct simple shear tests was undertaken on presheared polymer-treated material. Materials used were identical to those used in previously published studies on the impacts of polymer treatment in a ‘fresh’ condition. Shearing of the polymer-treated material generally appeared to lessen the impacts of the polymer treatment process. However, the behaviour of the material when sheared indicated that the polymer was still impacting the behaviour of the material in some respects. The results indicate the importance of the consideration of shearing on material behaviour when planning and designing a tailings deposit where polymer treatment is to be implemented.CITATION:Reid, D and Fourie, A, 2015. Effects of shear on the behaviour of polymer-treated slurries, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 215–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D E. G Connelly, K Y. Wong

Gold at the Harbour Lights Mine (HLM), WA occurs principally in pyrite (Py) and arsenopyrite (AsPy) minerals rendering it inaccessible to direct cyanidation. Froth flotation produces a concentrate with low mass recovery and with high recoveries of sulfides. After investigating several alternatives, a novel flotation process has been developed to separate the concentrate into pyrite and arsenopyrite rich fractions. The pyrite fraction is finely ground and cyanide leached, while the arsenopyrite is treated off-site. This paper describes the separation process from laboratory bench scale through to commercial operation at the HLM gold plant.

Jan 1, 2005

By J S. Laskowski

Froth flotation process requires the use of frothers. These important flotation agents are commonly characterised as either æselectiveÆ or æpowerfulÆ and are chosen following general guidelines and verification by laboratory and/or pilot plant tests. Fundamental properties of the flotation frothers have been extensively studied over the last few years. These studies have led to the development of standardised procedures to characterise frothers in terms of their ability to reduce bubble size and to increase foam stability. In this research project, the performance of five frothers in flotation of coal is evaluated and related to the fundamental properties of these agents. Since the recovery of water in the concentrate is closely related to the non-selective transport of solid particles by entrainment, the tested frothers are also assessed in terms of their ability to promote the transport of water towards the froth collection zone, both in absence and in presence of solids.

Jan 1, 2005

By B Ellis

Brunswick Mine is one of the largest underground zinc/lead mines in Canada, producing 3.4 million tones of ore annually. As mining activities advance to deeper levels, ground pressure also becomes greater. To cope with the highly stressed ground, the mine has taken some strategic measures to ensure the targeted production level. Such measures include the implementation of a pastefill system and transferring the mining method from primary/secondary stoping to pillarless pyramid stoping. With the pillarless mining method, stope sizes become smaller and the number of active stopes is also less than before. In addition, mining sequence and cycle time have to be strictly followed according to production schedule. The blasting project described in this paper tackles one of the steps in the mining cycle aimed at shortening the blasting cycle time in a stope. Furthermore, this project was conducted and managed with the Six Sigma initiative in Noranda which was implemented in the fall of 1999. Like a typical process review, the blasting operation was examined by breaking it down into many steps that can be quantified and measured. Each activity was then correlated with different factors associated with blast design as well as blast operations underground. It was found that the utilisation of voids plays a key role in the blasting cycle time. With improved void utilisation ratio, blasting cycle time has been reduced from an average of 12 shifts to ten shifts per stope. This improvement translates into approximately 180 000 tonnes of ore being blasted without any increase in manpower. This paper presents the technical aspects of the study, as well as some operational issues and improvements made during the project.

Jan 1, 2001

By Chunbao Z, Zhenchuan Z

As known to the international mining sectors, Hunan province, called as ' Nonferrous Native Area ', is the main base of nonferrous metals Pro- duction in China. There are over 194 nonferrous mines in this province, most of them distribute over the basin of Xiangjiang River. The state of management of wastewater in Hunan's nonferrous mines is outlined.The experiences and economic benefit in the management and treatment of wa- stewater in Bofang and Mayang copper mines, and at Shizhuyuan polymeta- llic mine, are mainly introduced. It concludes with measures and recommendations for future management and treatment of wastewater in Hunan's nonferrous mines.

Jan 1, 1988

By Giedl JG

Technical applications of computers within the coal industry are expanding rapidly with an increase in the number of users and user locations. Collinsville Coal Company Pty Ltd is an example of a remote and growing user company which has a Telecom link to MIM's ICL mainframe computer in Brisbane. The Planning Department is one of the technical user departments at Collinsville, with a variety of VDU, plotting and screen graphics hardware supported by the MIM Computing network. Current applications involve the storage, retrieval and manipulation of borehole information, plan and map production, volume calculations from survey data and mine ventilation modelling for underground Operations.

Jan 1, 1983

By L O. Filippov, I V. Filippova

Subsea massive sulfide deposits have particular mineralogical compositions and textural features differentiating them from onshore ore. When extracted from salty water and exposed to the air, massive sulfide samples strongly oxidise and soon become covered by thin layers of iron, copper and zinc-rich sulfates and oxides, as well as elemental sulfur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. Because of the variation of secondary mineralisation and porosity level, sea floor massive sulfides respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all types of sulfides from the gangue minerals, is one possible treatment technique to process sea floor ore. Sulfide recovery rate is, in most cases, excellent (>90 per cent). However, separation of the various mineral phases is difficult to obtain even when applying known methods used for onshore ore. Moreover, the flotation behaviour decreases dramatically with time of conservation, even when the samples were stored in a confined environment. High pH range, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulfides, does not have the same effect on subsea ore. Consequently, careful flotation procedure should be elaborated to obtain efficient mineral separation for this specific marine ore.CITATION:Filippov, L O and Filippova, I V, 2015. Processing of subsea massive sulfide ores by flotation – similarity and features with terrestrial ores, in Proceedings Third International Future Mining Conference, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Darvall

Magnetite ore blending has yielded signifi cant performance improvements in OneSteel’s magnetite concentrator. The magnetite concentrator beneficiates magnetite ore from the Iron Magnet Deposit and produces concentrate, which is pelletised, then fed to the OneSteel Whyalla blast furnace. Concentrator feed variability severely detracts from the concentrator’s performance, affecting both concentrate yield and grade, which impacts on all downstream processing costs.A coordinated approach has integrated mine planning, geological modelling and grade control, to minimise concentrator feed variability, through effective ore blending throughout the mining and stockpiling process.Mine planning personnel design shots that extend the full width of the orebody and hence across the stratigraphic profi le. Based on geological information contained in block-outs and in consultation with Geology, the Grade Control team allocates material to each primary stockpile, potentially from every stratigraphic domane in the orebody. This ensures primary stockpiles are designed with maximum practical homogeneity and consistency.Using only primary movement, the allocated ore is stockpiled in a layer-cake fashion. The ore is pimple dumped across the width of the stockpile footprint and on completion of a layer, it is dozed flat with an access ramp that allows dumping to commence on the next lift. The primary stockpiles are reclaimed normal to build direction and the magnetite is crushed, all in, to a concentrator feed stockpile.The ore is sampled at the crusher from a falling stream cut. These assay data, are used for benchmarking and control charting the grade and variability of concentrator feed stockpiles. The concentrator feed stockpiles have demonstrated a statistically signifi cant reduction of within pile variation, between pile variation and pile to pile variation, primarily attributable to the development of ore blending. The concentrator has seen sustained, improved performance as a direct result, which translates into lower concentrate cost per tonne and improved yield and quality.

Jul 11, 2011

By M J. Nugus

The Geita gold mines in north-western Tanzania have produced 5 Moz of gold from an estimated endowment of 15 Moz. They are generally classified as typical Archaean orogenic banded iron formations (BIF)-hosted gold deposits in banded iron formations as described by Goldfarb, Groves and Gardoll (2001); Neall and Phillips (1987); Phillips and Powell (1993) and Neall (1987). The controls on gold mineralisation have been reassessed to conclude that Nyankanga, and we conclude that Nyankanga, the largest deposits within the group, developed during a dynamic and protracted deformation history intimately associated with several stages of hydrothermal fluid flow and alteration. The fluid-induced fractures associated with gold mineralisation are primarily manifested as submillimetre to metre-scale fractures and breccias developed preferentially in rocks that have been previously deformed and altered by silicification or seafloor metasomatism. This realisation detracts from the exploration and mining strategies that would solely concentrate on fluid pathways and associated wallrock alteration and veining solely within the BIFs as hosts for economic gold mineralisation.

Aug 22, 2011

By J Harris, P Kirsch, R LaBouchardiere

æMining + Health in DevelopmentÆ is a project funded by the International Mining for Development Centre (IM4DC, 2012) to develop a centralised database of corporate sustainability initiatives for managing and improving occupational and public health, based on information extracted from social and environmental reports of major mining, oil and gas (MOG) companies. This register of materials has the potential to increase stakeholder awareness of the unique health risks impacting the minerals industry, employees, their families and surrounding communities, as well as to inform stakeholders on global industry approaches to health management.Data and preliminary outcomes from analysis of different MOG corporate sustainability reports on public health and disease management are presented for six African countries (Democratic Republic of Congo, Ghana, Mozambique, Sudan, Tanzania and Zimbabwe) and six Asia-Pacific countries (Indonesia, Mongolia, Pakistan, Papua New Guinea, Philippines and Vietnam).With the minerals industry facing ongoing rapid growth worldwide, including continuous expansion into developing regions, the æMining+Health in DevelopmentÆ project will inform industry, civil society and regulators of current health management practices and programming among the different sectors of the minerals, oil and gas industries and across various regional operations. This baseline information will serve as a resource for minerals industry managers, providing a forum for sharing best practice health management approaches amongst MOG companies.CITATION:LaBouchardiere, R, Harris, J and Kirsch, P, 2012. Mining and health in development - An inventory of global resource industry health initiatives in developing countries, in Proceedings International Mine Management 2012, pp 75-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By E Amini, N Beaton

Application of ore pre-treatment technologies such as Grade Engineering and in-pit ore treatment require comprehensive analysis to show proven value is being generated by switching away from the current practices. Considering most mining operations last several decades; the pre-treatment technologies must be investigated over life of mine (LOM) to truly show value was generated or lost. Therefore, a value chain flowsheet model has been usually developed to run those analysis/simulations over LOM using a set of defined ore characteristics and the operating equipment capacities. The Integrated Extraction Simulator (IES) has been used for this type of LOM simulations as it has the necessary flexibility to accommodate the whole mining value chain flowsheet in one platform and provide essential computation power to run mass simulations for the given scenarios using the resource block model. This allows to forecast the value chain response over the LOM for all given scenarios in a feasible amount of time. The traditionally developed flowsheets for the analysis/simulations are usually limited to the mineral processing plant and were developed based on a single audit conducted on the plant in a very short time, e.g. several hours. The process plant is being operated with a certain ore at a certain condition during the short audits which would not reveal the true capacity of the operation equipment when ore characteristics changes. Therefore, it would be impossible to define the true capacity of the equipment and identify the constraints along the value chain. In this study, a methodology was developed to identify the constraints along the value chain and implement those in the IES flowsheet using process information. Also, the equipment models were fine-tuned to represent the true capacity of the equipment in the flowsheet using the same data set. The methodology was tested over five process plant in two operations and showed the performance forecast was significantly improved over the traditional methods being used so far. Then those high-fidelity flowsheets were used to evaluate the ore pre-treatment technologies proposed by the relevant resource company experts.

Nov 10, 2020

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Pan, Q H. Li, D Q. Zhu, C C. Yang, X Wang, Z Q. Guo

Al2O3 in natural iron ores generally occurs in goethite, kaolinite, gibbsite, hematite and iron carbonate. When the content of alumina in sinter increases from 1.11 per cent to 3.50 per cent, the reducibility of sinter decreases with the addition of four different types of alumina. When gibbsite and kaolinite are added, the low temperature reduction disintegration (RDI+3.15 mm) of sinter increases with the increase of Al2O3 content in the range of 1.5 per cent to 3.5 per cent. Furthermore, when adding pure reagent alumina, the increase of Al2O3 content in the range of 1.5 per cent to 3.0 per cent will increase the RDI+3.15 mm of sinter. The addition of ferric oxide–alumina spinel with the Al2O3 content in the range of 1.5 per cent to 2.5 per cent, also increases the RDI+ 3.15 mm of sinter. The influence difference is results from the change of the mineral composition and microstructure of sinter because of the occurrence state of Al2O3. Under the condition that Al2O3 content of sinter is 2 per cent, the porosity of sinter with kaolinite is 37.26 per cent, and the shape is irregular. When gibbsite and ferric oxide–alumina spinel are added, the porosity of sinter is about 16 per cent, and the pores are round. When pure reagent alumina is added, the porosity of sinter is 17.49 per cent, and the pores are regular and small. When kaolinite, gibbsite and ferric oxide–alumina spinel are added, platy calcium ferrite is mainly formed in the sinter, and some of it is columnar calcium ferrite. On the other hand, when pure reagent alumina is added, in addition to platy columnar calcium ferrite, acicular calcium ferrite is also formed in the sinter.

Nov 8, 2021

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

By A Dennis, T Hunter, R Coleman

For metallurgical plant design, it is necessary to progress through successive phases of test work, piloting and process development before involving all the other engineering disciplines and “freezing” the process design criteria and flow sheet. This process usually relies upon the experience, skills and personal preferences of various technology providers, study and engineering entities, test work and metallurgical laboratories and, most importantly, the owner’s team and its operators. Current industry trends include lower grades, more complex orebodies, geometallurgy in defining orebody variation and design envelopes, more common “hybrid” plant processes and the market demands for more reliable, timely and predictable early plant performance.This paper will discuss interaction of these trends and provide guidelines for the level of detail and technical complexity required for a number of different “typical” examples. The paper will pay particular attention to the study definition level translated into the required detail and certainty needed by the overall process “owner” and original equipment manufacturer (OEM) equipment suppliers to ensure the best real plant performance. Some recent case studies will be discussed. In many projects, at a late stage of project definition, it has become common practice to undertake a “value engineering” phase. Although it could be argued that this should be undertaken earlier, it is largely driven by an overall need to reduce capex and “optimise” the perceived “fat” built into the project during the detailed design process. This value engineering can be very counterproductive to project timing and operational performance and warrants discussion.The paper is intended to promote discussion on a topic of wide interest. The authors’ diverse backgrounds and experiences are integral to the views in this paper.CITATION:Dennis, A, Coleman, R and Hunter, T, 2017. Critical process design considerations from test work to operations, in Proceedings MetPlant 2017, pp 12–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017