Search Documents

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M A. Knackstedt

Coupling between deformation processes and rock permeability is a major factor influencing the architecture of fluid migration and the localisation of ore deposition in several types of hydrothermal ore systems in middle to upper crustal regimes. Permeability in many hydrothermal systems is controlled by a dynamic competition between deformation-induced porosity-creation processes and porosity-destruction processes. Localisation of deformation within faults, fractures and shear zones leads to flow localisation, with large-scale flow systems forming when active faults and shear zones link to create percolation networks. Numerical modelling techniques are used to explore the growth of fracture networks and evolution of network connectivity during progressive deformation. Initial results indicate that networks reach a percolation threshold at very low strains. Near the percolation threshold, flow is localised along a small proportion of the total fracture population and favours localised ore deposition. At higher strains, flow is distributed more widely throughout the fracture population and may provide reduced potential for production of high-grade deposits. The distribution of mesothermal gold deposits along a small subset of the total population of co-active faults and shear zones in the Archaean Yilgarn Craton in Western Australia indicates that some hydrothermal systems maintain themselves near the percolation threshold for a substantial part of the lifetime of the system. Fluid-driven growth of fault/fracture/shear networks may lead them to self-organise near the percolation threshold.

Jan 1, 1999

By G Sparrow

The Murray Basin is being heralded as the next major mineral sands province in Australia. Already exploration programs have delineated extensive commercial deposits and several companies are progressing with plans to produce zircon, rutile and ilmenite in the Basin. As these deposits are developed consideration will need to be given to several key issues of the Murray Darling Basin; the availability of fresh water and management of salinity in the area being two of them. In this paper ideas being developed in CSIRO that link the processing of mineral sands with the salinity problem in the Basin are presented. The proposal presented here is to process saline water to produce industrial minerals with large volume applications and to produce value-added products from the mineral sands in the Basin using reagents produced from the saline waters. Processes to produce titania pigment and zirconia consume chlorine, caustic soda, soda ash and hydrochloric acid, all derivatives of salt (sodium chloride). There may be a good economic incentive if these processing plants were located in the close vicinity of each other.

Jan 1, 2001

The New Technology of Enrichment of a Fine Low-Grade Tungsten from Complex Multi-Metallic Ore

Sep 13, 2010

By R Razanatsimba, A Galli

A mining company has entered into contractual commitments to supply certain quantities of its product to clients in each time period. Failure to fulfil its obligations would damage its reputation as a reliable supplier. The planned production would normally be sufficient unless major problems such as highwall failures, roof falls, natural disaster, or strikes that interrupt production or delays in obtaining environmental permits, occur. To overcome these difficulties, the company may be able to obtain more of the commodity: from its strategic stockpile (if there is sufficient there); by buying it on the spot market; or for some commodities such as gold and uranium, by leasing it. Two sources of uncertainty, the spot price of the commodity and the occurrence of serious incidents that interrupt production, are considered. For simplicity it is assumed that the commodity price follows a geometric Brownian motion, that productions incidents have a binomial distribution, that they are independent from one time period to another and that they do not affect prices. A branching tree structure is used to model the joint evolution of prices and production incidents. The aim of this research project was to evaluate the companyÆs options for fulfilling its contractual commitments. When evaluating these options, multi-stage stochastic programming with recourse was used to solve this problem because in addition to providing the dollar value of the project, it gives decision-makers the æroadmapÆ to reach the optimal value. That is, how much material should be bought/sold on the spot market, how much to add to/subtract from the stockpile, how much to lease and in the worst case what the shortfall would be, for each time period as a function of the current spot price and breakdown status. A case-study over a five-year period is used to illustrate the proposed procedure. In this study the production would be sufficient to cover the companyÆs contractual commitments unless production incidents occur. Focus is on evaluating the impact of the quantity initially in the stockpile on the value of the project when the commodity market is tight, that is, when only small quantities can be bought on the spot market or by leasing.

Sep 26, 2011

By I Lourel

In evaluating the installation of an in-pit crushing and conveying (IPCC) system for any mine, a number of options are available for each of the dig side, transport and dump side operations. Some of them are moreappropriate than others; given the pit arrangement, the material being handled and the rates at which it needs to be moved. This paper seeks to document the options that might be employed, and to rank them in terms of their applicability at any mine and their practicality overall, with a view to nominating those that would be most suitable for further study.

Jan 1, 2009

By C D. Rawlings

An assessment is made of the potential for thick seam underground mining of black coal in Australia. A brief summary is given of the geo-mechanical environment and previous mining history existing in a number of areas of particular interest from the point of view of thick seam mining. A classification of thick seam mining methods is presented with emphasis on the critical geo-mechanical parameters influencing the performance of such methods. A summary is made of perceived geo-mechanical research requirements related to thick seam mining in Australian coalfields.

Jan 1, 1980

By J de Witte

When used in suitable ground conditions, rock bolts can have advantages over other permanent tunnel lining solutions. Permanent rock bolts offer flexibility in tunnelling profile and rapid rock bolt installation can enable time and cost savings. There are also disadvantages when considering the suitability of rock bolts for permanent support installations. These generally concern achieving the specified durability requirement over the specified design life. By investigating alternate approaches to rock bolt installation, quality assurance (QA), monitoring and design life it may be possible to alleviate some of these concerns.The design and construction benefits that can be realised through the use of rock bolts are primarily related to reducing project program time. This time reduction could be realised if rock bolts are considered as a permanent solution, with the installation being completed as a part of the primary excavation cycle. Any reduction of the program could allow direct and indirect cost savings and in the case of a major project, allow the revenue stream to be realised earlier.Currently ambiguity exists where the treatment of rock bolts as permanent support components is inconsistent with that of (often identical) ground anchors, as utilised in stabilising cut and cover structures. The ground support design process, implementation and testing are generally similar, though the acceptance of rock bolts as long-term support elements is treated differently to ground anchors in technical specifications.This paper discusses some of the benefits available through the use of rock bolts. It offers different solutions to the concerns surrounding durability, including alternate approaches to installation, Quality Assurance practices and monitoring solutions. The selection of an alternate design life is also investigated as another means of alleviating concerns around long-term durability. The paper will also provide an indication of savings that could be expected through the use of rock bolts as part of a long-term support system.

Mar 8, 2011

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

Continuous pH and Pulp Potential Measurements During Complex Sulfide Ore Flotation

Sep 13, 2010

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha, H B. Wurst

In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink–?float analysis. Using traditional sink–float method it is not possible to sample and automatically measure. This fact, as well as time, cost and safety aspects, as well as required and manageable sample size of the sink–float method have prompted the search for a new approach for establishing separation performance criteria. This is especially important as performance levels of separator plants can be maximised if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes available in time. The new method to establish washability and associated performance information utilises at least two measurement technologies concurrently: single energy X-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy X-ray transmission and image processing.If used as a standard laboratory device the continuous build-up of the washability curve allows to evaluate the statistical significance of the sample size during measurement.The measuring method can even be improved if it is combined with an automatic sampling system that feeds a continuous and representative particle stream to the analyser. Then the value of the collected data increases considerably since the washability data are additionally available in time to be considered in the control of the process plant. The washability curve can be derived and is continuously updated based on the particles measured during the past time interval. Older curves and results are stored in a database and can be retrieved for later reference. This technology now enables automated sampling and integrated automated measurement, which was previously not possible.This incorporation of an automated washability monitor at a representative sample gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested using a range of samples with different densities, varying from 1 g/cm3 (coal) to 5 g/cm3 (iron ore).CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P, Wurst, H B and Ha, J, 2017. Inline analysis of washability parameters for process control, in Proceedings Eighth World Conference on Sampling and Blending , pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Missen, P Currie, J Bohan, D Clark

AGL is one of Australia’s leading integrated energy companies and the largest ASX listed owner, operator and developer of renewable energy and thermal generation in the country. AGL owns and operates the 2210 MW Loy Yang A power station and adjacent 30 Mt/a brown coalmine in the Latrobe Valley, Victoria. It also supplies coal to the nearby 1050 MW Loy Yang B power station owned by the GDF Suez (Engie)/Mitsui partnership. The mine is currently nearly 5 km long, more than 2 km wide at the operating face and up to 200 m deep. AGL employs a large workforce at Loy Yang and a substantial amount of services are performed on-site by contractors and consultants.GHD provides mine planning, earth sciences, civil/geotechnical engineering, dam surveillance, plant engineering and environmental services to AGL Loy Yang through an alliance framework. GHD is one of the world’s leading professional services companies operating in the global markets of water; energy and resources; environment; property and buildings; and transportation. In addition to GHD’s global footprint, the company also has a significant Victorian presence, including a permanent, well-resourced regional office in Traralgon, approximately 10 km from Loy Yang, as well as a permanent site office.A joint paper on the Loy Yang mine professional services alliance model was written for the AusIMM International Mine Management Conference in 2006 by Woods and Wood. Now ten years on, this paper provides an overview of the present relationship and arrangements, including the continued transformation of the alliance model and maturing of the relationship contract.These are challenging times, with increasing cost and regulatory pressure driving change in the broader energy and resources industry, and locally including both the mining and power sectors at Loy Yang. Flexible models to achieve a balance between internal personnel and access to key external skills, whilst achieving value for money and transparency, is increasingly critical. The right drivers and performance measures are essential, particularly when confronted with potential major technical and environmental risks (considering significant ground failure and fire events that have occurred elsewhere within the Latrobe Valley over the last decade) within a sector that is reducing costs and optimising production.This case study discusses the alliance status and changes, reasons behind adjustments and what the future is likely to hold. The paper also explores the validity of the original objectives and the extent to which they have been achieved. The philosophy of the alliance is to continue closely aligning the objectives of the two companies in the best interests of the Loy Yang site and immediate surrounds/stakeholders. Quality of service, costs, timeliness, health and safety (H&S) and some operational activities (aquifer depressurisation) remain important aspects and are reflected in key indicators for which performance is measured.CITATION:Clark, D, Bohan, J, Currie, P and Missen, J, 2016. AGL energy, Loy Yang and GHD – a further case study in alliancing: ten years on, in Proceedings International Mine Management Conference, pp 321-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Industrial minerals by definition are minerals used as part of an industrial process and usually are one of a number of components, eg finely ground Limestone is an extender in the manufacture of paint. They are normally non-metallic and non-fuel, but like all generalisations there are a number of exceptions. Take rutile û a source of titanium, a metal and also the raw material in the manufacture of titanium dioxide pigment. Industrial minerals under this general definition include construction and agricultural minerals. They are included in the same grouping, principally because their sources are similar and in many cases the raw material, example limestone, can be multi-functional. Calcium carbonate raw materials such as limestone, are used in a wide range of applications from industry as an inert filler, to agriculture as a 'lime' source and to construction and as an important component in the manufacture of cement. As far as this paper is concerned I will avoid discussing the agricultural or construction applications, including burnt lime production.

Jan 1, 1985

The results of precious metal exploration carried out by Amoco Minerals New Zealand Limited over EL 33-137 in the Longwood Range, Southland, are described. Widespread gold and platinum in alluvial deposits on the perimeter of the range and anomalous gold in stream sediments on its southern and south western flanks indicates that the precious metals were probably derived from erosion of the mafic rocks of the Longwood Complex.

Jan 1, 1983

Flotation of Composite Synthetic Particles

Sep 13, 2010

By J M. Shekiro

In the chloride process to manufacture TiO2 pigment, feedstocks containing higher TiO2 contents (high-grade ores or HGOs) are favoured in order to minimise production of undesirable by-products. Most of today’s HGOs are produced through the smelting or reduction and leaching of ilmenite, processes which consume significant energy and/or produce large volumes of non-titanium materials that may have to be landfilled. In order to improve the economic and environmental sustainability of its TiO2 business, the DuPont Company, working with Kobe Steel Ltd, has developed an innovative process called TiRON for making HGO. Using a rotary hearth furnace, the process reduces ilmenite to a high TiO2 slag and metallic iron granules. The TiO2 slag is suitable for TiO2 pigment manufacture, and the iron is suitable for steel making. TiRON can process sand or rock ilmenite of varying compositions and particle sizes. Fossil fuel instead of electricity supplies the energy for the reduction. Dusts and off-spec materials are recycled. These process attributes, together with capital requirements estimated to be significantly lower, give TiRON substantial economic, environmental, and process flexibility advantages over conventional ilmenite upgrading processes. TiRON has been demonstrated at the semi-works scale, and preparations are being made to bring it to the pilot scale.

Oct 5, 2011