Search Documents

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D R. Wines

The design of near-surface civil infrastructure requires detailed consideration of the geological/ geotechnical conditions, excavation geometry and sequence and ground support measures to ensure stability of the underground openings and minimal impact on overlying or adjacent infrastructure. Twin parallel road tunnels have been designed and built with connecting cross passages and a piggyback busway tunnel as part of a large infrastructure project in Australia. The tunnels were excavated in poor to fair quality rocks using road headers. Temporary ground support includes shotcrete, rock bolts and canopy tubes. Extensive numerical analyses have been performed to analyse the expected behaviour of the tunnels during excavation, including two-dimensional analyses using UDEC and three-dimensional analyses using FLAC3D. Structural defects in the rock are explicitly included in the 2D analyses to examine the potential for localised ground instability. The stress redistribution is captured by the 3D modelling with an accurate representation of the complex excavation geometry and the detailed excavation and support sequence. This paper presents the modelling methodology, numerical results and discussions on integrating both 2D and 3D analyses to achieve reasonable design.

Mar 8, 2011

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By A C. Edwards

The Mongol-Okhotsk belt consists of detached fragments of the Circum Pacific fold belt which have been trapped within the Mongol-Okhotsk fold belt. In its western part, the structures of the belt form an east-facing loop that is not connected with the other orogenic structures of Central Asia. In the eastern part of the belt (the Mongol-Okhotsk suture zone) the terranes form a zone between the Siberian craton to the north and the Bureya composite terrane to the south, that is linked with the Circum Pacific belt. The accretionary terranes, together with their Precambrian backstops, form a series of consistently-stacked, paired units that are bounded by northwest and north trending sinistral strike-slip faults. The ages of the rocks forming these accretionary complexes vary from Late Precambrian - Carboniferous in the west to Cambrian - Jurassic in the east. The terranes developed due to a progressive westward stacking of the accretionary complexes during the process of accretionary growth. The magmatic rocks young eastward indicating that migration of the magmatic front of the arc followed the eastward growth of the accretionary complexes. The accretionary terranes may be differentiated by their Paleozoic lithological assemblages. Only the Selemdzha, Niman, and Kerbi terranes located in the eastern part of the Mongol-Okhotsk suture zone contain significant amounts of black shale, and it is these terranes that host the bulk of the hardrock and placer gold mineralisation that is present within the suture zone. Gold mineralisation is present both as vein style and disseminated mineralisation within structural duplexes.

Jan 1, 1999

Past arguments advocating reverse circulation sampling against blasthole sampling are reviewed to present the debate under a different light. The advantages and disadvantages of each drilling method are compared, and the choice is presented as an informed trade-off between them.

Mar 1, 2010

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

By Y Xu, T Rowles, B Dareeju, A Dissanayake

Recent updates on tailings dam design guidelines require analysis of undrained (short-term) stability with the application of the SHANSEP model. The SHANSEP model, which was originally developed for alluvial soils, predicates that the Undrained Shear Strength (Su) increases with increasing effective stress. Residual soils by their nature do not necessarily follow this relationship. This paper examines an alternate method to define Su over a range of effective stress conditions for residual soils. Residual soils, formed by weathering of their parent rocks, are generally micro-structured in nature. The microstructural features, such as interparticle bonding, play a fundamental role in stress-strain behaviour of the residual soils. As interparticle bonding is independent of effective stress and void ratio, the undrained shear strength of residual soils is expected to be less dependent on effective stress than alluvial soils, especially at low stress levels. A series of triaxial tests conducted on residual soils, however, indicated that the undrained shear strength and the undrained shear strength ratio (Su/σv’) are to a degree dependant on effective stress. It was found that the undrained shear strength ratio is significantly higher under low stress levels and progressively reduces with increasing effective stress. Based on the laboratory testing data, a strength function with varying undrained shear strength ratios can be developed for the residual soils under the stress range anticipated for a design of a tailings dam. This includes capping the input undrained strength at lower effective stresses based on the drained (effective) and minimum undrained strength. The Factor of Safety (FOS) calculated for the embankment utilising the traditional limit equilibrium (LE) method indicated the application of undrained strength function for the residual soils can provide a significant optimisation for the embankment design compared to adopting a constant undrained shear strength ratio or constant undrained shear strength in the design.

Jul 1, 2021

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and SnAg deposits ofBolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolome, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolome area.

Jan 1, 1995

Construction work on one of the world's largest landslide stabilisation projects is drawing to a close in Central Otago. Begun in mid 1990, major stabilisation work has been carried out on seven large rockslides which will be partially inundated when the Clyde dam reservoir (Lake Dunstan) is filled. The work has required the construction of 14.5 kilometres of tunnel, 60 kilometres of surface drilling, 78 kilometres of drilled drainage holes and five million cubic metres of earthworks. The stabilisation programme has been carried out by the Electricity Corporation of New Zealand as part of the Clyde Power Project, a hydroelectric development on the Clutha River.

Jan 1, 1992

Commercially interesting deposits of zeolite rich tuffs and amorphous silica have been discovered recently in the Taupo Volcanic Zone (TVZ), North Island, New Zealand. This paper reviews them and comments on the potential for further discoveries. Potential markets for these unusual industrial minerals are discussed.

Jan 1, 1997

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

By R C. Schodde

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Over the last decade (2005–2014), a total of 439 significant deposits of gold and base metals were found in the world. Twenty (or 4.6 per cent) of these deposits were in the Pacific/South-East Asia (Pacific/SE Asia) region. In terms of contained metal, the region accounted for 1.6 per cent of gold and 13.8 per cent of copper found in the world. With regard to nickel and zinc/lead, the region’s contributions were insignificant.Over the same period, the Pacific/SE Asia region accounted for 6.6 per cent and 12.6 per cent of all gold and copper exploration expenditures in the world respectively. After adjusting for by-product credits, unreported discoveries and likely growth in resource, the unit discovery cost for the region was US$199/oz (compared to a world average of US$50/oz). For comparison, the unit discovery costs for the previous decade were US$55/oz and US$25/oz respectively. The region’s unit discovery cost for copper was US$0.036/lb (versus a world average of US$0.040). For comparison, the unit discovery costs for the previous decade were US$0.026/lb and US$0.008/lb Cu respectively.The region’s mediocre discovery performance doesn’t reflect its distribution of known mineralisation. Some countries within the region have a very good endowment per square kilometre.It is noted that the intensity of exploration (and resulting success) would be boosted if governments provided a more mining- and investment-friendly business environment and generated better precompetitive geological data sets (to identify new exploration targets and boost the country’s perceived mineral prospectivity). A multivariable regression analysis of a decade of data from the Fraser Institute’s mining company surveys found that a ten point increase in the Policy Perception Index or a 0.1 point increase in the Mineral Potential Index could boost (in the short term) exploration expenditures by 1.9 per cent and 2.7 per cent respectively. The resulting economic benefits of an expanded mining sector would be significant. The same story applies elsewhere in the world.CITATION:Schodde, R C, 2015. Discovery performance for gold and base metals in the Pacific/South-East Asia – 2005–2014, in Proceedings PACRIM 2015 Congress, pp 25–34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

A summary of a proposal to develop a 20 000 tpa underground gold operation in a Forest Park. The environmental constraints are severe and affected the mine development planning and choice of mining method. The mine will use trackless methods to access the narrow 1.5 m ore shoots, and to mine ore by cut and fill methods. The use of Microscoop and CT 1700 HE electric LHDs for mucking, together with special drilling attachments for drilling, is central to efficiency and small Kubota diesel haulers will be used for carrying ore to surface.

Jan 1, 1986

The kinetics of the hydrogen reduction of iron oxides in granular calcined bauxite were studied at 550-1,050°C in a shallow bed reactor. The iron oxides behaved as a dispersion of particulate iron oxide in a porous alumina matrix in which the iron oxide particles were reduced independently. The observed rates of reaction were found to be virtually independent of the bauxite grain size. At 800,°C and above, the reduction was multistage, Le.1. Fe203 +2Al203 (matrix) ?2FeAl204, and2. FeAl204? Fe0 +Al203.Reaction 1 was very rapid. Reaction 2 was much slower, the latter stages being controlled, at least in part, by phYSIcal changes of the Fe0 and a-Al203 produced in the reaction. Owing to the observed nature of the material, the reaction rate controlling steps could not be determined.

Jan 1, 1972

By V L. Los, G J. Abramson

The paper examines three types of polar zoning of ore-forming and associated elements that can be detected from geochemical data. Polar zoning is mapped in the form of geochemical ore systems of various ranks. Various types of polar zoning can be found in some systems, which present a general geochemical model of the ore object. The genetic basis of zoning is examined from the perspective of the conception of geoelectrochemical redistribution of matter, including ore-forming elements. The volume of the geochemical ore system may be used in the prognosis of resources for every rank.

Jan 1, 1999

By M A. Wells

A new approach to more reliably predict the Ni (and Fe, Mg) composition of Ni laterites was tested for RC samples from the (siliceous) oxide–style, Siberia North deposit, Kalgoorlie Nickel Project (KNP), in the north-eastern Yilgarn (WA) using partial least squares regression (PLSR) analysis of diffuse reflectance spectra over the 380 - 2500 nm wavelength range with a multi–element chemistry data set. PLSR cross-validation models were developed to predict FeO, MgO and Ni contents in composite samples with bulk composition limits of >0.08 wt per cent Ni and <6 wt per cent MgO. Calibration and validation models showed a strong, linear trend for predicting FeO and, to a lesser extent, Ni content, whereas PLSR models for predicting Mg content were less reliable. This reflected the prevailing mineralogy and associated element deportment within the oxide laterite profile. For example, Fe and Ni distribution is controlled by relatively few minerals, predominantly goethite and, to a lesser extent, the Fe3+-bearing smectite, nontronite. Magnesium is associated with a range of Mg-bearing minerals, some of which are compositionally complex (eg serpentine, talc, chlorite, smectite and carbonates). Magnesium chemistry alone does not reflect the varied mineralogy of samples with relatively high (5 - 6 wt per cent) MgO contents, which can be spectrally distinct. Hence, samples with similar Mg contents, though comprising Mg-bearing minerals with distinct reflectance spectra, were difficult to model (eg smectite versus Mg-carbonates). The findings of this study demonstrate that characterisation of Ni laterite composition may be achieved as part of routine logging of either drill chips or diamond drill core using PLSR analysis, but that a detailed understanding of the mineral-element association is essential for reliable predictive analysis. This has particular relevance to characterising the geometallurgy of Ni laterites, especially where deposits may be classed as the same type, but have distinct compositional and mineralogical differences.

Sep 5, 2011

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986