Search Documents

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

[United Engineering Trustees, Inc. ALBERT ROBERTS. '47 R. M. ROOSEVELT, '49 RALPH B. WILLIAMS, '48 The Engineering Foundation F. F. COLCORD. '46 M. A. PRENTIS. Jn.. '48 It. >I. ROOSEVELT. '49]

Jan 1, 1946

By Jay N. Fairbanks, Richard G. Robinson

This paper discusses a computer program and related formulas for fire fighting responses by coal mine personnel. The computer will interpret the mine air analysis, print reports, and provide relevant graphs allowing quick and accurate responses to coal mine fires.

Jan 1, 1983

By N. A. Gokcen, M. Ohtani

Thermodynamic intevaction pararnetevs of elements E2(2), for dilute binary solutions of a component "2" in liquid iron, i.e., E(22) = 9 In f2/?N2 where f2 is the activity coefficient and N2 the mole fraction, and E(3) 2 = In f2/ N3 dilute ternary solutions of "2" and "3," and the carbon saturation parameter sc(3) (In f c/ N3) N c/N Fe for N3 - 0, are critically examined and correlated. It has been found that the interaction parameters and the atomic numbers of alloying elements follow regular periodic putterns. PHYSICO-chemical behavior of alloying elements in molten iron have become the subject of numerous investigations during the past 25 years. Consequently, the mutual effects of elements in the iron-rich solutions Fe-C-X, Fe-N-X, Fe-H-X, Fe-O-X, and Fe-S-X where X represents an alloying element, have gradually become better understood. These effects for a given temperature and pressure may be expressed by the interaction parameter of Wagner1, 2 derived briefly in the following manner. The complete differential of the Gibbs free-energy equation at constant temperature and pressure is dF = Fl dn, + F2 dn, + F3 dn3+ . . . [ 1] where F is the free energy; F 1, the partial molar free energy of "I"; and n,, the number of moles of "i." Cross-differentiation of this expression* *Cross-differentials are obtained as follows: Since the order of differentiation of F with n2 and n3 is immaterial, the left sides of the second differentials are equal, hence the derivation of Eq. [2] is obtained. For a dilute solution of components 2 and 3 in solvent 1, with the substitution of RT In f i = Fi xs for Fi where fi is the activity coefficient, and Fixs is the excess partial molar free energy, Eq. [2] becomes O) [3] where N2 and N, are the mole fractions. The interaction parameters are defined by

Jan 1, 1961

By Henry Mackay

THE interesting paper recently submitted by Messrs. Tobelmann and Potter' shows that chemical problems have developed which are of great interest in this new and important branch of metallurgy. Those who realize what a process of this kind really involves will agree that it deserves a better name than "leaching process." The word leaching conveys the idea that the copper is simply leached out of the ore with acid and then precipitated on iron; the chemistry of such a process would be of little interest. As, however, during the first year's operation of this plant 24,400,532 lb. (11,067,837 kg.) or about two-thirds of the produce, was electrolytic copper, while 7,992,033 lb., or about one-third, was cement copper, it would seem more appropriate to term the process electrochemical. It further appears, from the particulars given, that efforts have been made to have the entire production in the form of electrolytic copper. -This could be done if the chemistry of the problem were kept in balance, so that it would not be necessary to discard any solutions that carried copper and acid of commercial value. A process, such as that under consideration, in which the copper is precipitated from solution by electrolysis, the solvent being at the same time regenerated, is one that requires special chemical and electrochemical knowledge and experience if all the -copper in solution that has been extracted from the ore is to be successfully and economically produced as electrolytic copper. The object of this paper is to discuss, from the practical and theoretical standpoints, the chemical and electrochemical problems involved in the working of a process of this kind, and' which must be solved to keep it in chemical and electrochemical equilibrium. In such a process, if the chemical balance is maintained, a solution can be used alternately as a

Jan 9, 1919

By AIME AIME

THE 131st meeting of the American Institute of Mining and Metallurgical Engineers was held in New York on Feb. 16 to 20, 1925, with the largest registration of any previous meeting, the total being 1320 compared to 1276 in 1924. The technical sessions were more largely attended and aroused more discussion than ever before. There were joint meetings with the Mining Section of the National Safety Council, under the auspices of the Industrial Relations Committee of the Institute and two very important lectures, the Howe Memorial Lecture, under the auspices of the Iron and Steel Committee, and the lecture by Dr. Carl Benedicks, of Sweden, on Corrosion, under the auspices of the Institute of Metals Division. The Petroleum Division conducted its annual Symposium on Oil which will be published later in book form. At the annual business meeting on Feb. 17, the following ticket was elected, and the reports of the President, Treasurer, and Secretary 'were presented:

Jan 1, 1925

NEW MEMBERS The following list comprises the names of those persons who became members during the month of February, 1914: Members ASANO, KOSAKU, Vice-Mgr..: Ashio Copper Mine, Shimozuke, Japan. BIRD, FRANK H., Constr. Engr E. 417 Sixteenth Ave., Spokane, Wash. COLES, HENRY 0., Chem Copper Queen. Cons. Min. Co., Bisbee, Ariz. COLLEY, HYLTON H., Met Copper Queen Cons. Min. Co., Douglas, Ariz. DALEY, MITCHELL J., Mill Supt Utah Apex Min. Co., Box 753, Bingham Canyon, Utah. FISHER, GEORGE EDWARD, Director, 3d Vice-Pres., Grasselli Chemical Co. 1551 East 115th St., Cleveland, Co. FRASER, EVERETT L., Mill Supt Tightner Mines Co., Alleghany, Cal. FRASER, WILLIAM L., Min. Engr North Star Mines, Grass Valley, Cal. FROLLI, ALBERT W. Min. Engr 216 North Main St., Salinas, Cal. GEARHART, FRANK B., Chief of Smelter Dept., N. J. Zinc Co., 405 Columbia Ave.. Palmerton, Pa.

Jan 3, 1914

By F. W. Glaser, W. Ivanick

A pressure-sintering method was used to produce binder-free and very dense TiC specimens. Some physical properties of these TIC bodies were determined and found to compare favorably with those of certain cemented Tic grades. It was also observed that the hot transverse rupture strength of TiC bodies remained substantially the same regardless of the amount or type of binder material used. STUDIES of the structure and physical properties of refractory materials have been intensified recently because of the urgent need for nonstrategic materials that retain their strength at high temperatures. Research aimed at determining and improving the physical properties of cemented carbides and borides has been accelerated with a view toward possible use of such materials in connection with turbine blades, rocket nozzles, and other high temperature applications. On the hypothesis that the strength requirements in connection with some of the above applications could be met only by proper choice of cementing agents for such refractory materials, the literature describing the physical properties of borides or carbides was reviewed. However, with a few exceptions,'-" references were found only to compositions containing at least one or more auxiliary binder metals. Cobalt and nickel are among the most frequently employed cementing agents. The melting point of Tic (approximately 3250°C) and therefore the sintering temperature, at which notable densification of a cold pressed Tic powder compact could be expected in the absence of a liquid binder phase, is relatively high. The present study makes use of a high temperature, pressure-sintering procedure, recently described by one of the authors in connection with the sintering of binder-free ZrB,," to produce dense bodies of sintered Tic—free of any cementing agent. During the course of this sintering study, some physical properties of dense Tic bodies produced by this method will be discussed. Materials, Preparation of Samples, Testing Methods The procedure for the forming of Tic powder consisted of mixing graphite and TiH, powders in stoi-chiometric proportions, and heating this mixture in a H, atmosphere and carbon crucible by high frequency, to temperatures ranging between 1900° and 2100°C (3452" and 3812°F). The powdered carbide was then comminuted and screened to the desired particle size. Table I shows the chemical analysis of the two grades that were employed for the production of samples during this work. Bodies of Tic, approximately 2.5xlx0.5 cm were produced in graphite molds that were heated by direct conduction. Sintering was carried out at temperatures for time intervals ranging from approximately 0 to 30 sec under a constant pressure of about 1.3 tons per sq in. An alternate method for the production of samples consisted in cold pressing the individual Tic grades at pressures ranging from 4 to 10 tons per sq in. and sintering in a hydrogen atmosphere in graphite crucibles heated by high frequency induction. Sintering temperatures ranged from 2600° to 2900°C (4715° to 5255°F). Electrical testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp at room temperature. Cross-sectional areas as well as densi-

Jan 1, 1953

By A. Faber du Faur

At the request of some of the members to whom I have shown a collection of specimens of sulphur from southern Utah, I herewith present some notes relating to the mines and the method of extracting the sulphur from the ore. In preparing these notes I have borrowed from a paper by Prof. G. vom Rath, published in the Neue Jahrbuch fur Mineralogie, vol. i., 1884, dated Salt Lake City, December, 1883. The Cove Creek sulphur-bed, now worked by the Dickert & Myers Sulphur Co., is in Beaver county, near the line of Millard county. It was first discovered by Mr. Ferdinand Dickert in 1869 ; other beds in the same neighborhood mere found by him from 1872 to 1875, making altogether 22 mining claims. The want of railroad communication prevented the early development of these claims; but in 1883 Mr. F. Dickert put up a plant for extracting sulphur from the ore, which proved a perfect success; and in 1885 the property was transferred to a stock company organized under the laws of Utah. The railroad station nearest to the Cove Creek mines is Black Rock, on the Utah Central Railroad, 204 miles south from Salt Lake City, and about 26 miles west of the mines. The road from Black Rock to the mines passes through desert and lava-bed, to the road leading from Kanosh to Beaver, which latter road it joins near Cove Creek fort, a square stone enclosure, erected by the Mormons for protection against the Indians. Cove Creek fort is situated near the eastern limit of a plain bounded on the west at a distance of about 12 miles by the Mineral range, and on the east by the Sulphur mountains, forming part of the Tushar mountains. To the northwest the plain runs into the Sandy desert. About 3 miles from the fort rises a solitary hill about 1000 feet above the

Jan 1, 1888

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

United Engineering Trustees, Inc. W. D. B. MOTTER, JR., '40 A. L. QUENEAU, '38 ALBERT ROBERTS, '39 The Engineering Foundation GEORGE D. BARRON, '40 F. F. COLCORD, '38 A. L. QUENEAU, '38

Jan 1, 1937

United Engineering Trustees, Inc. W. D. B. HOTTER, JR., '44 A. L. QUENEAU, '45 ALBERT ROBERTS, '43 The Engineering Foundation GEORGE D. BARRON, '44 F. F. COLCORD, '46 A. L. QUENEAU, '45

Jan 1, 1942

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By J. Chipman, G. G. Hatch

One of the important functions of the iron blast furnace is the desulphur-ization of pig iron before it enters the steelmaking furnaces. However, the increasing concentrations of sulphur in the metallurgical coke, source of approximately 90 pct of the sulphur present in the blast furnace charge, and demands for higher rates of production within recent years have increased the need for greater desulphurization within the iron blast furnace. Furnace operators are beginning to look for desulphurizing agents other than blast furnace slag to accomplish the desired degree of desulphurization. A considerable amount of work has been done on desulphurization outside the furnace with soda ash, calcium carbide and various synthetic slags. Whether the desulphurization of pig iron is accomplished wholly inside the furnace or partly inside and the remainder outside, will be determined by the economics involved. Regardless of which is the case, it is believed that it is necessary to have a better understanding of the physical chemistry of desulphurization by blast furnace slags. To this end, it is the object of the present investigation to attempt what is believed to be the first equilibrium study of the distribution of sulphur between liquid pig iron and a wide range of blast furnace slag compositions. Review of Literature There is a considerable amount of information in the literature concerning the desulphurizing power of iron blast furnace slags, the solubility of various sulphides in the slags, and the effect on desulphurization of temperature, of elements dissolved in the liquid iron, and of viscosity. However, there is nothing to indicate that the equilibrium distribution of sulphur between liquid iron saturated with carbon and iron blast furnace slags has been studied experimentally. Wentrupl has made probably the most detailed study of the desulphurization of pig iron to date. He considered that there are three distinct aspects involved, namely: 1. Desulphurization within the blast furnace (by lime and manganese). 2. Subsequent desulphurization by manganese. 3. The effect of subsidiary reactions on the desulphurization by manganese. The experimental work carried out by Wentrup was devoted mainly to obtaining a better understanding of how desulphurization by manganese was accomplished in the mixer and the ladle. Particular attention was given to the part played by carbon, silicon, and phosphorus associated with manganese in the iron, and the effect of temperature on desulphurization. The experimental results indicated that desulphurization by manganese is purely a process of crystallization of manganese sulphide. The addition of silicon to iron melts containing 3.5 pct carbon and less than 0.5 pct manganese had no noticeable effect on desulphurization, but with 1-2 pct manganese the silicon additions improved the desulphurization. Additions of phosphorus also resulted in improved desulphurizati011 by manganese, but the effect was not as marked as in the case of silicon. It was also found that desulphurization by manganese was further improved by lowering the temperature. In order to explain desulphurization inside the blast furnace, Wentrup considered the system iron, sulphur, calcium, oxygen, manganese. (silicon). The distribution of sulphur between the metal and slag was represented by the following equation: (SS) _ (S)Fe + (S)Ca + (S)Mn .... [S] = [s] [1] The parentheses and the brackets represent the equilibrium concentrations in weight per cent of the slag and metal constituents, respectively. Since FeS D (FeS) _ (FeS) (S)Fe LfeS - [FeS] [S] [2] (CaO) + S e (FeO) + (S)Ca _ (FeO)(S)Ca. (S)Ca _ (CaO) Kl = (CaO)[S] [S] ~K1(FeO) [3] Mn + S D (S)Mn (S)Mn (S)Mn K' = [MnpT "1ST = *lIMnJ !4) Substitution of Eq 2, 3, and 4 into Eq 1 resulted in if = L- + *> (Sol + K^ (S) [51 Eq 5 was used to calcu1;lte -f^j and [S] at 1480°C for slags containing 30-50 pct lime, 0.1-2.5 pct iron oxide, 0-26 pct silica, 2 pct sulphur and iron analyzing 1.5 pct manganese. The value for LFaB at 1480°C was found to be equal to 4.5, based on the experimental work of Bardenheuer and Geller.2 The results of the calculations are shown in Table 1. Although the slags are hypothetical and do not represent the range of compositions found in ordinary blast furnace practice, the calculations indicate that lime is effective in controlling desulphurization only if the iron oxide and silica contents of the slag are kept low. Schenck3 did not claim K1 to be a true equilibrium constant, but an empirical value which varied with the silica content of the slag.

Jan 1, 1950

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

By J. L. Humphrey

The origin of roof bolting is obscure, but is believed to have begun some 40 years ago in the mines of St. Joseph Lead Co. in southern Missouri. It was not until after World War II, and more particularly after 1949, as a result of the concentrated effort of the USBM, that roof bolting attracted widespread interest. It is estimated that at the end of 1954, 26 pct of all bituminous coal mining in the U. S. was being done under roof bolts. Those mines alone use nearly 2,000,000 roof bolts per month, according to USBM statistics. Uses in metal mines are increasing rapidly, as confidence and knowledge grow. The application has found equal success in other fields, such as tunneling work for dam and waterway construction and right of way maintenance on highways and railroads.

May 1, 1956

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By Noel Cunningham

MANY excellent descriptions of the mills of the, Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 2 ½ years' mill operation in the district-i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.-There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15? of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured .and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a ½ -in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling.' In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more-or less blocky at times, and with ref¬erence to Class B this is indicative or low gold content.

Jan 3, 1915