Search Documents

By Howard Martens

HARDNESS behavior of commercial titanium alloys following various heat treating processes has been studied for some time. However, the hardness of such alloys following a definite measured cooling rate from the single phase region has not been reported. Therefore, a series of experiments was conducted on the three alloys: 150A, 130A, and 130B. The manufacturers gave the following compositions for these alloys: Ti 150A: 0.045 pct C, 0.069 pctN, 1.32 pct Fe, and 2.68 pct Cr; RC 130A: 0.13 pct C, and 7.9 pct Mn: RC 130B: 0.11 pct C, 3.5 pct Mn, and 3.2 pct Al. A method similar to that described by Greninger was used, and the cooling rate varied from 6" to 9200°F per sec. The cooling curves were recorded on a Speedomax or a recording oscillograph, and the hardness was measured on a Tukon hardness tester using a Knoop indentor with a 500 g load. The curves of Fig. 1 show the variation of the Knoop hardness with the cooling rate for these three alloys. The alloys 150A and 130B behave in a similar manner, as shown by the curves. In neither of these alloys was it; possible to retain the high temperature ß phases, even by the most rapid cooling rate. The slow cooling rates produced a typical ß structure in these two alloys. As the cooling was increased, these phalses became more finely dispersed and the hardness increased. This increase in hardness with cooling rate continued for the 150A alloy until a rate of approximately 1000°F per sec was reached. At this cooling rate, the structure showed the result of the dif-fusionless transformation of the ß solid solution to the supersaturated a solid solution which is referred as a'. At higher cooling rates, the structure showed no change and the hardness showed no great change, as indicated by the dotted portion of the curve in Fig. 1. The increase in hardness with cooling rate for the 130B alloy continued until a rate of approximately 300°F per sec was reached. At this rate the structure was produced and the maximum hardness was reached. Higher cooling rates caused no marked changes in hardness or structure. The alloy 130A behaved in a different manner, as shown by the curve of Fig. 1. The structure produced by the slow cooling rates was a typical a+ß structure, which became finely dispersed as the cooling rate increased. The hardness increased with cooling rate and reached a maximum at approximately 120°F per sec. At this maximum hardness, the structure showed the result of the decomposition of the ß phase into the ß + phase structure. As the cooling rate was increased, smaller amounts of the at phase were formed and the alloy became softer. For cooling rates of 3000°F per sec and above, the high temperature ß phase was retained and the hardness of the alloy did not change markedly. Acknowledgment This paper presents the results of one phase of research carried out at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-0rd 18, sponsored by the Dept. of the Army, Ordnance Corps.

Jan 1, 1957

By H. M. Chance

Jan 1, 1886

By Eli T. Conner

(Wilkes-Barre Meeting, June, 1911.) My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its vicinity, which have excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. 'Fortunately, there were no pupils in the building at the time; but the thought of the possible result, bad the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken tip and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Sep 1, 1911

By D. R. Cook, W. M. Shepard, H. T. Morris

The East Tintic district in central Utah has produced ores of gold, silver, copper, lead, and zinc valued at more than $120,000,000. All of this ore has been produced from blind ore bodies in Paleozoic sedimentary rocks that are concealed beneath hydrothermally altered volcanic rocks and cut by intrusive bodies of Eocene age. The Paleozoic rocks, which range in age from Early Cambrian to Mississippian form the core and limbs of a large, northtrending asymmetric anticline that is cut by low-angle thrust faults, high-angle transcurrent faults, mineralized fissures and faults, and normal faults that are both older and younger than the mineralized fissures. The ore bodies generally may be grouped into two classes: ( 1) massive replacement bodies that are rich in silver, lead, zinc and manganese and (2) fissure veins that are valuable primarily for their content of gold, copper, and silver. The replacement ore bodies are localized chiefly in the Middle Limestone Member of the Ophir Formation of Middle Cambrian age where it has been thrust-faulted against older or younger rocks and cut by northeast-trending mineralized fissure zones. The fissure veins primarily are productive only in the Lower Cambrian Tintic Quartzite. Extensive lowgrade deposits of lead-zinc-silver ore recently have been discovered in Devonian carbonate rocks in the Lower plate of the East Tintic thrust fault but as yet are unevaluated. The principal guides to ore include: ( 1) intersections of northeast-trending fissures and crossbreaking faults that brecciate the carbonate rocks; (2) zones of late-stage pyritic, calcitic, and sericitic alteration in the lavas; ( 3) primary geochemical anomalies in the altered rocks; and ( 4) mineral zoning patterns of the known ore bodies. The present development of the Burgin mine would seem to assure the continued productivity of the district for at least a decade.

Jan 1, 1968

By C. P. Sandberg

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

JAmes E. Howard, Watertown, Mass.:—In connection with this paper, it is the desire of the Watertown laboratory to receive suggestions as to the lines of work and the particular direction along which the examination of the ingot-metal should proceed, and any suggestions so offered will be noted with care, and the tests conducted so as to embrace such features as it is thought desirable to have investigated. To me the question of structural continuity seems of para-

Jan 1, 1909

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By Ralph W. Marsden

The natural iron ores of the Lake Superior Region in the United States are being replaced by iron-ore concentrates produced from magnetite- or hematite-rich horizons in the Precambrian cherty iron formations. The production of natural ores will soon be less than one-half of the total ore shipped annually. The tonnage of natural ore produced will continue to decline until it is a minor percentage of the ore shipped. The natural ores include (1) soft ore, (2) hard ore, ( 3) conglomerate ore and ( 4) siliceous ore. The soft ores are the important ore type and are sometimes termed "Lake Superior type ore". These ores are in situ deposits of hematite and limonite formed by the leaching of silica and other gangue materials in the iron formations. The leaching is believed to have been done by downward moving surface waters. In deep ore deposits, generally over 1000 feet below the present surface, circulation and leaching action may have been assisted by hydrothermal activity. Hard ore deposits occur on the Vermilion and Marquette ranges where hematite or magnetite has replaced the silica (and possibly some silicates) in cherty iron formation. These ores commonly occur in structural situations favorable for the movement of hydrothermal waters. The ores are believed to be the result of hydrothermal action with iron, possibly from the iron formation, transported by hydrothermal waters to areas favorable for the replacement of silica by iron oxides. Certain stratigraphic horizons of the Lake Superior Precambrian cherty iron formations contain sufficient iron as magnetite or hematite, with a grain size and texture that will give adequate mineral liberation, to yield an ore-quality product after grinding and concentration. The magnetite-rich deposits are termed magnetite taconites. These ores occur on the Mesabi, Gogebic, and Marquette ranges. Magnetite taconite ores are unenriched cherty iron formation and are the result of the sedimentary deposition of the iron formation and the metamorphic history of the rock. The commercial quality hematite-rich iron formations in Michigan are termed jasper ores. The jasper ores are being mined on the Marquette and Menominee ranges. These ores are composed of specular or granular hematite associated with quartz and iron silicates. The jasper ores appear to be recrystallized iron formations in which iron, prior to recrystallization, occurred as hematite.

Jan 1, 1968

By H. H. Campbell

MANY attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits-a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It may be urged that the microscopic structure must be taken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all test-pieces be made under the same conditions; and it is be¬lieved that the tests described in this paper satisfy that require¬ment. The investigations were made at the works of the Pennsylvania Steel Company,. Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham

Jan 1, 1905

The first discovery of gold in Montana is credited to François Finlay, a half-breed, from the Red River country, in Canada; he went to California during the early days and learned there how to wash the gold from placer deposits; then, on his return, he crossed Montana and found gold on the western slope of the Rocky Mountains, on Gold creek, a minor tributary of the Hell Gate river, in what is now Deer Lodge county. That was in 1852.* Finlay did not find enough gold to induce him to continue at work, but six years later a group of miners, led by the brothers James Stuart and Granville Stuart prospected on this same creek, obtaining about ten cents to the pan. They, however, were harassed by the Blackfeet Indians, and they were also handicapped by lack of proper tools; so they too desisted from further operations. Two years later, in 1860, Henry Thomas started to work on Gold creek with three sluice-boxes hewn out of green timber that he cut on the spot. With this simple apparatus he won from $1.50 to $2.00 per day. This may be considered the fist instance of systematic mining in Montana. Meanwhile the Stuarts went to Fort Bridger, in southwestern Wyoming, where they remained as traders until 1861, when, again lured by the gleam of gold, they returned to the valley of the Deer Lodge and resumed prospecting, using 10 sluice-boxes that were brought from Walla Walla, in Washington, 425 miles distant. In the summer of 1862 they were joined by many others, chiefly from Colorado, in consequence of an exchange of

Jan 1, 1932

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968

By John J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these .melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. In the early days, the process was thought of as a simple one. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. Using cryoscopic data, Rolin has determined the following composition for molten cryolite. Na2,AlF 3Na + 3F + AlF [1] He postulates the following equation for the ioniza-tion of alumina at low concentrations Al2O3 Al + AlO2 +O. [2] At concentrations above 0.025M he supposes the ionization of alumina to proceed as follows Al2O3 AlO + AlO2. [3] Rolin's mechanism of electrolysis for the more concentrated solution in Eq. 3 is as follows. The AlO' ion migrates to the cathode. where it is dis- charged, giving metallic aluminum and 0' ions which migrate to the anode. The AlO2- ion migrates to the anode, where it is discharged, giving Al ions and oxygen which reacts with carbon to form CO2 In the case of the extremely dilute solution in Eq. 2 the Al ion migrates to the cathode and the AlO2-and 0 migrate to the anode as before. Another possible mechanism for the electrolysis follows. Ionization of Cryolite Na3AlF4 = 2Na + 2F + NaAlF, Na + AlF-AlF+Na + F [4] Addition of Alumina 2Na2AlF+ 2AL2O4 6Na + 3A12O3F4 [5a] Al2O2F 2AlOF2 [5b] Cathode Process AlF, + 3e+ 4F + Al. [6] Anode Process AlOF2 + 2F AlF1 + 1/20, + 2e or A12O2F + 4F-2A1F; + 0, + 4e. [7] Although both Rolin's and the present mechanism of the Hall process may be qualitatively satisfactory, present data are not adequate for quantitative tests of the theories.

Jan 1, 1959

By P. H. Royster

On the Continent, ferromanganese has been produced in the blast furnace almost continuously since 1876, but little definite information concerning the practice is to be found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country, prior to 1904, but one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public..In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations; so the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Operating data were collected by the Bureau from eleven ferromangahese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P; the dimensions of seven of the furnaces are given in Table 1. The companies from whom this information was obtained, and to whom should go the credit for whatever value this information may possess, are the Bethlehem Steel CO.,

Jan 1, 1920

Jan 1, 1953

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

Elected Died 1895 *ABBOTT, AI ATTHUR 1908 1882 *ABBOTT, ARTHUR V 1906 1905 * ABE, MASAYOSHI 1909 1903 * ADAMS, CHARLES C. 1905 1906 * ADAMS, JOHN C. 1913 1905 * ADAMS, WILLAMS 1909 1903 * ADAMS, W. EDWARDS 1910 1884 *ADDY, MATTHEW 1896 1906 * AFFLECK, WILLIAM A. 1911 1889 * AKERS, WILLIAMS A. 1906 1905 * ALABASTER, RUPPERT C. 1911 1899 * ALBERGER, LOUIS R. 1911 1894 *ALLEN R B 1896 1905 * ALLEN, R. SCOTT 1906 1874 * AMIOT, H. 1892 1886 *AMSLER, CARL 1894 1898 ** ANDRSON, JOHN W 1905 1895 *ÅNGSTROM, CARL 1901 1887 * ARCHBALD, JAMES 1910 1900 * ARLETT, GEORGE H 1906 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885

Jan 1, 1917

By Charles W. Frey

COMPRESSED air is one of the most useful tools that the mine operator has at his disposal. It is clean, nontoxic, easily handled, and can be distributed anywhere that a man can drag a length of rubber hose. Without it a great deal of drilling would still be a laborious hand process, and although the John Henry of legendary fame could beat a mechanical drill, John Henrys are few and far between, and in the long run the air drill is the victor. As a general rule, horizontal compressors are lubricated by mechanical lubricators, which furnish oil to the cylinder walls, whereas vertical units are splash lubricated. In most horizontal machines oil is introduced at the top center of the piston, from which point it can run down and lubricate the rest of the piston. Some large units introduce oil at more than one point on the cylinder wall, the necessity for this and the number of points of introduction depending upon the size of the cylinder.

Jan 1, 1938

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949