Search Documents

By D O. Tan Sky

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1980

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By H. R. Aldrich

THIS paper is not a treatise on the theory and practice of magnetic surveying. It merely presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern Wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretations of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies.

Jan 1, 1928

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

The Morley Coal Measures (Upper Cretaceous) at Ohai Coalfield were deposited in an intermontane basin alluvial environment of entirely terrestrial aspect. Within this regional setting, three distinct types of depositional environment are recognised; these are: (i) a sand-dominated (South Saskatchewan type) braided river system characterized by channel-bed dunes and possibly compound bars; (ii) a well-drained floodplain environment frequently subject to crevasse-splay and overbank-flow sedimentation; and (iii) a poorly-drained, commonly peat-accumulating backswamp environment locally traversed by tributary drainage systems and occasionally inundated by crevasse splays and overbank flows. All major coal seams of the Morley Coal Measures originated within forest moors under predominantly telmatic (periodically inundated) conditions. The peat-forming vegetation comprised largely arborescent forms (dominantly conifers), in addition to pteridophytes and bryophytes. In-seam vertical variations in coal type indicate groundwater levels initially decreased and then increased during the lifetime of a particular peat swamp, possibly in response to a change in the migration direction of an adjacent fluvial system. The proposed depositional model for the Morley Coal Measures has the potential to be utilised during exploration programmes and mine development to impart greater objectivity to predictions concerning seam geometry and continuity, trends in coal type and quality, and likely roof and floor conditions.

Jan 1, 1985

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

The whole of the iron ore required by the Broken Hill Proprietary Company Limited at the Newcastle Steel Works, and Australian Iron and Steel Limited, at Hoskins' Kembla Works, is drawn from the Iron Knob, Iron Monarch, Iron Prince and Iron Baron deposits situated in the northern part of Eyre's Peninsula, South Australia.The Iron Knob and Iron Monarch deposits are near the township of Iron Knob, approximately 42 miles W.S.W. of Port Augusta, whilst the Iron Prince and Iron Baron deposits are some 18 miles due south from Iron Knob, in another group of leases, the adjacent township being known as Iron Baron.The ore mined at Iron Knob, Iron Monarch, Iron Prince and Iron Baron is conveyed on the Company's 3ft. 6-in. gauge tramway to Whyalla, on the western side of Spencer's Gulf, approximately 45 miles south by west of Port Augusta whence it is shipped to Newcastle and Port Kembla.SHORT HISTORY.The establishment in South Australia of the lead smelting industry at Port Pirie, Dry Creek and Port Adelaide in the...

Jan 1, 1937

With the post-war expansion of mmmg activities on its Western group of mines, the management of Lake View and Star Limited has commenced a project for the improvement of underground ventilation.The major part of this project is to provide adequate return airways for the ventilation of the deep levels. To this end, the Ivanhoe South Extended shaft is being enlarged, and ultimately an exhaust fan with a capacity of 180,000 cu. ft. of air per minute will be installed at the shaft collar.Prior to 1932, the shaft was used exclusively for baling water from the 800 and 2,000 ft. levels. These two levels are the only ones connected to workings from the Horseshoe lease. After the installation of pumping plant at the Horseshoe Main Shaft, baling was discontinued, and the water was graVitated from dams to the pumps on the 1,000 and 2,000 ft. levels.Water makes into the shaft, through a series of fault planes, between the 600 and 1,500 ft. horizons. The total flow is 16 gal. per minute, of which approximately 7 gal. per minute graVitates to the 800 ft. level. As a big proportion of the water dropped uncontrolled through the shaft, a downcast current of air approximating 20,000 c.f.m. was induced. This air ventilated a limited area of workings in the Horseshoe lease, between the 2,000 and 2,360 ft. levels.In 1938, it was decided to reverse the direction of the airflow in the shaft. Work was carried out to pipe the...

Jan 1, 1948

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By A. G. Pasamehmetoglu

The swelling process is an important problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from pedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the pedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By Joseph Pogue

OVER a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institu-tion, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles under-lying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. NATURE OF PRORATION Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By Aysan Molaei, Kristian E. Waters

"Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, it is not efficient in the extraction of low concentration metal ions from aqueous solutions. Predispersed solvent extraction (PDSE) is an alternative method for solvent extraction which implies colloidal liquid aphrons as extracting agents in order to reach higher interfacial area and lower reagent consumption. This work investigated important parameters in PDSE of nickel ions from dilute aqueous solutions by fractional factorial design of experiments. Four experimental parameters, the initial extractant concentration, initial surfactant concentration, equilibrium pH and phase volume ratio (organic to aqueous ratio) were investigated. The important parameters were determined as well as important interactions between these parameters. It was found that extractant concentration, phase volume ratio, and equilibrium pH are the most significant experimental parameters. However, the interaction between surfactant concentration and other parameters was determined as significant interactions.INTRODUCTIONNickel is one of the key components found in cars, mobile phones, rechargeable batteries, kitchen appliances, and steel industry (Anyadike, 2002). It is one of the most important metals produced by Canada which is in the five top nickel producers in the world. Despite a 24% decrease in the nickel prices from 2011 to 2014 the nickel global mine production increased by 36% between these years (U.S. Geological Survey, 2015; Nickel - Statista Dossier, 2015), which shows the increasing demand for nickel. This high demand leads producers to consider the production of nickel from low grade ores and other secondary sources such as process wastewaters. The removal of nickel ions from process wastewater is also important due to environmental considerations. Nickel is known to be a human carcinogen and it may cause serious lung and kidney problems, pulmonary fibrosis, gastrointestinal distress, and skin dermatitis if it exceeds the critical level (Borba et al., 2006; Fu & Wang, 2011)."

Jan 1, 2016

By Marc C. Bétournay

"Surface crown pillars, acting to safely protect underground workers and operations from surface elements, are recognized, herein, as distinct from conventional deeper underground pillars. Moreover, because of the variation in mining and geological conditions that exist from mine site to mine site, each case is viewed as unique. A review of numerous case studies and existing literature indicates that there is little general information or systematic problem-solving approach associated with them.A design process, not unlike that of other engineering disciplines, is presented to correct these deficiencies. As part of its purpose, it will inform operators of the key elements required for design and will address the problems of these appendages. The design, while taking into consideration possible surface crown pillar settings and inherent characteristics, is founded on a step-by-step procedure starting with site investigations through to monitoring or pillar recovery. The process is flexible, in that it incorporates decision making and changes in mining strategy. The purpose of each step is explained and each step is extensively described in terms of the required equipment and methods for field work, analysis and support measures. Analytical formulae and studies from several fields directly applicable to surface crown pillars are also given. Recommendations for future research studies are presented."

Jan 1, 1987