Search Documents

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By Kosta Fytas, Nour-Eddine Chaouai

"Selection of the appropriate kriging plan during indicator kriging estimations is of a paramount importance to the precision of ore reserve estimation. However, very little is known on the sensitivy of indicator kriging results when changing the kriging plan parameters (mainly search distance and number of samples). This paper evaluates the effect of the search distance and number of samples on indicator kriging results using a gold deposit as a case study.IntroductionBlock estimation using kriging is based on the autocorrelation function (variogram) on one hand and on the kriging plan on the other. As far as the variogram is concerned it is more or less subjectively adjusted and this is reflected on its parameters (range, sill, nugget effect and anisotropy). The effect of a poor estimation of these parameters on the kriging variance of ordinary kriging has been proven very important (Brooker, 1986). Choosing a kriging plan is generally a difficult matter depending on the estimation type (global or local). Generally there is not a unique kriging plan be cause there is not a unique structural analysis (variogram). There are no rules or dogmas in choosing a kriging plan but it is rather a function of the sampling pattern (David, 1982).Structural analysis requires the hypothesis of quasistationarity but very often either the data available within the zone of quasi-stationarity are too many so that the search distance is reduced during kriging or the data are too few to satisfy a stationary kriging system (Journel and Huijbregts 1978). As a rule, the larger the neighbourhood, the more precise the estimates should be , but for large neighbourhoods the hypothesis of stationarity does not always hold (Rivoirard 1987; Armstrong and Champigny 1989)."

Jan 1, 1991

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By W. Kuckshinrichs

Metallic raw material flows are characterized by a complex global network of producers and consumers, as well as by a multitude of ecological, economic and social impacts across national boundaries and on different scales. This leads to the need to develop methodologies, which allow identifying obstacles that prevent metallic raw material flows to contribute to sustainable development. From a scientific point of view CRC 525 (Martens 2003) has developed an holistic indicator set consisting of approximately 80 different indicators. This set is taking into account the multi-dimensional character of sustainable development. Moreover the indicators reflect different system boundaries according to different actor levels and decision contexts. The full indicator set is important in scientific considerations and suitable for scientific awareness creation. However, to fulfil the function of a decision support approach for political and economic decision-makers some modifications are of central concern. At first a reduction of the full indicator set by selection of core indicators enables decision-makers to deal with complex issues of contrary economic and societal protection targets. Secondly, as thresholds of indicators justify societal call for action, they are discussed against its political or scientific origin. The proposed methodology is exemplified by indicator-based studies of the material flow of aluminium.

Jan 1, 2003

By Nicholas Macrae Steven

Abstract - The Shaba-type Luamata Cu-Co(-Ni) deposit (11°50_S, 24°28_E) is located in a tectonic slice of Katangan Roan Supergroup (Mines Group) sedimentary rocks, surrounded by younger Kundelungu Supergroup lithologies in the external fold and thrust belt of the Lufilian Arc. Luamata is a classic central African copper clearing in dense woodland, visible as a tonal botanical anomaly on Landsat imagery. Supergene Cu-Co mineralization (especially malachite and subordinate chalcocite, digenite, covellite, and copper and cobalt oxides) and, probably hypogene, bornite, and chalcopyrite are hosted by altered, but essentially unmetamorphosed, moderately dipping, dolostones and dolomitic shales. Alteration products include talcose dolomite, sericite rocks and intense silicification and brecciation. Friable yellow shale is best mineralized with cobalt (up to 0.43 wt%), whereas, highest copper grades occur in brecciated, silicified shale (up to 13.5 wt% CuO). Soil copper and cobalt contents are up to 2.2 and 0.6 wt%, respectively. A newly identified nickel zone (where soil contents exceed 0.1 wt% Ni) fringes the Cu-Co deposit. Polymictic, matrix-supported breccias with a calcareous matrix that underlie the Cu-Co deposit are interpreted to be fluidization breccias related to thrust tectonics and the emplacement of the Mines Group slice. Although small compared to the Kolwezi district Shaba deposits in the Democratic Republic of the Congo, Luamata exhibits all the classic features of an ore deposit type (with low calcite contents), whose high metal concentrations could potentially be very profitably exploited by low-cost opencast mining and hydrometallurgical recovery methods.

Jan 1, 2000

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By Pawan Bharadwaj, Wim Mulder, Thomas Tscharner, Guy Drijkoningen, Rob Jenneskens

"The Earth’s properties, composition and structure ahead of a tunnel boring machine (TBM) should be mapped for hazard assessment during excavation. We study the use of seismic-exploration techniques for this purpose. We focus on a seismic system for soft soils, where shear waves are better and easier to interpret than compressional waves, as has been shown over the last decade. The system is intended to be deployed on the machine’s cutter head, with a few seismic sources and sufficiently many seismic sensors to tackle spatial variability and noise characteristics. An important property of the newly developed system is its ability to process data with very little human interaction. Images need to be available in near real time, without human interactions slowing down the imaging process. This can be achieved by employing Full Waveform Inversion, which minimizes the difference between modeled and observed data. Because this method may suffer from local minima in the cost function if the data lack low-frequency information, we employ a dedicated seismic source that can generate sufficiently low frequencies for the relevant length scales. With data acquired in a number of field settings that mimic realistic TBM configurations, we show that the designed seismic system can successfully look ahead of the TBM and offers a valuable capability to support decision-making during tunnel excavation. INTRODUCTION While excavating a tunnel with a Tunnel Boring Machine (TBM), the geology and the ground conditions along the planned tunnel trajectory need to be investigated in order to safely and efficiently carry out the underground operations. This entails detecting the occurrence of boulders, foundations, pipes and faults, necessary to prevent hazards and time-consuming delays in the tunnel boring operations. In order to facilitate ground prediction ahead of a TBM, techniques as used in seismic exploration can be deployed. Two components common to seismic-exploration techniques are data acquisition and processing, the latter including inversion. We will discuss each of these for the application to tunnel excavation with TBM, in particular for soft soils."

Jan 1, 2016

By S. Beitler

The availability of renewable energy does not meet the demands of consumption. Hence, fossil fuels will continue to be an important energy source, and coal promises to cover the requirements for the coming decades. Because of its high energy content, deep lying bituminous coal and anthracite are important for energy generation. One trend in the future of coal mining is thin seam mining, because thick seams more and more have been exploited. A well-known and approved longwall mining method for thin seams is plowing which has big advantages compared to a shearer because of its compact design. The extraction of those thinner coal seams will become more and more important in coal industry and therefore the plow will receive more attention in future. Most approaches in longwall automation are focused on the shearer and need a more or less intelligent exploitation machine. Therefore those approaches cannot be used for the plow technology. The authors introduce a shield-data-based horizon control (SDHC). The developed approach integrates the shield data provided by the roof support and process monitoring into the horizon control process to keep the plow in seam even if the seam trend changes. This control concept can be used for the shearer as well as for the plow. The basic idea of SDHC for plow application will be introduced in this paper and first simulation results will be shown.

Aug 1, 2013

By William A. Vogely

Mining employment in the United States declined from 986,000 employees in 1948 to about 600,000 employees today. This has occurred even though the Index of Physical Volume of Mineral Production (1957-59=100) has increased from 88 to 111 and the value of mineral production measured in constant(1957-59) dollars has increased from $14.7 billion to approximately $19.3 billion. Average unit mine value has increased 24% as compared with a 34% increase in prices in general. Apparent consumption has increased more than domestic production, indicating an increased dependence on imports. The mineral economy presents a complex pattern of development factors in the post-war period. This article presents a technique by which the various forces that have been acting on the market for a mineral commodity may be sorted out and by which the extent of the impact of technological change in use as well as the technological change in production can be measured. If one is interested in delineating fully and completely the impact of technological change upon the mining industries, it is not sufficient to describe the increase in productivity reflected by the above employment and production figures. What is reflected there is only the effect of technological change in the production function of the commodities under concern. These effects are obviously very substantial and have major implications for labor, capital and supplying industries. However, they are not the only effects of technological change and, in fact, may be relatively minor when the impact which arises because of changing technology in the using or consuming industries is considered.

Jan 4, 1965

By John Birkinbine

FOR two years past the Warwick Furnace, at Pottstown, Pa., has attracted attention by the remarkable work done in it, and a statement giving details of its operation and the unexpectedly short blast of 1880 will be acceptable to every member who studies blast-furnace practice. There are so many interesting features in con¬nection with this blast, and so much to be learned from investigating it, that the results of a thorough examination are offered to the Institute sans theories. In collecting the information, the courtesy of the various officers of the Warwick Iron Company was of material advantage, every facility for investigation being extended and an inspection of records being kindly permitted. In the following description these authoritative data are given in full where practicable, without making the paper too prolix, and the

Jan 1, 1881

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By A. Dienenthal

"The casthouse floor has always been one of the most dangerous working places on a blast furnace or a ferro-alloy/nonferrous furnace. Apart from working in an atmosphere including toxic gases, fumes, and dust, the workers have to perform hard and heavy manual work close to runners and ladles filled with hot liquid metal and slag.Before the invention and installation of tapping equipment the tap-holes were opened and closed manually. Opening was done by means of steel bars and sledgehammers, whereas the tap-hole was closed by repeatedly ramming small amounts of clay or refractory material into the tap-hole, again with the help of long, heavy bars. In addition, on blast furnaces the blast had to be stopped, since it was impossible to close the tap-hole properly against the blast furnace pressure. This stoppage of the blast resulted in regular losses of production. Around 1900 a major change in technology occurred. Samuel W. Vaughen, superintendent of the blast furnace department of the Cambria Iron company at Johnstown, Pennsylvania (USA), invented the first clay gun in 1895 (Wiley, 1896) (Figure 1)."

Jan 1, 2014

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By M. P. Oommen

This paper provides a brief look at a proposed short-longwall for coal, development. The proposed method is an attempt to realize the advantages of longwall mining in deposits that, historically, would only be minable by continuous mining methods. An overview of the proposed layout, development requirements, production rate, ventilation scheme and other associated features is provided. This mining method could help operators in above-drainage seams where minable areas are smaller. It may also have application in areas that are peppered with gas wells and in environmentally sensitive areas which preclude the use of conventional longwalls.

Jan 1, 1993

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012