Search Documents

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By YONGQIONG YANG, Ning Wang, CHONGGUANG LUO, LI ZHU, Hanjie Wen, SHENGJIANG DU, Hannian Gu

Niobium in kaolin clay from the Late Permian sequences was reported in the range of several hundreds of micrograms per gram and was considered as a potential resource for its high concentrations and large areal distribution. Ti-bearing minerals associated with kaolin clay were identified as the main host phase for niobium in some case studies. However, the correlation between the concentration of niobium and titanium is poor, and the types of Ti-bearing minerals and modes of occurrence of niobium are not clear. Typical kaolin clay samples from the Late Permian sequences from southwest China were characterized, and the final products derived from kaolin clay sample were investigated using XRF, ICP-MS, XRD, SEM, and TEM (EDS). The results reveal that there were three types of TiO2 mineral phases in the clay samples: (a) massive TiO2 minerals and (b) aggregates of nano TiO2 minerals did not contain niobium while (c) granular TiO2 minerals were the source of niobium from the EDS analysis. The granular TiO2 minerals included anatase and rutile, both of which were the sources of niobium in kaolin clay in the current study. The findings are of great theoretical implication for source and origin study of Ti-bearing minerals and guidance for separation and recovery of niobium from kaolin clay.

Nov 30, 2020

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By M. Howe

This is a study of the impact of cyanide from mining waste on riparian communities, primarily vegetation, near Whitewood Creek, down-stream from Homestake Gold Mine in Lead, South Dakota. Cyanide is used in gold processing and the effluent, until fairly recently, was discharged directly into Gold Run Creek which empties into Whitewood Creek. Vegetation, soil, and water were collected from four different sites over a six month period, and samples tested for cyanide concentration. Data indicate a relationship between cyanide in soil and its uptake by certain plants, also, that the Homestake cleanup effort has made the stream viable again.

Jan 1, 1983

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By Kunzo Amano

Fully-bonded rock bolts have been widely used in construction sites and mines in recent years. The purpose of this investigation is to prove the effectiveness of rock bolt supports in unstable ground through in-situ tests and numerical analysis. 2. MEASUREMENTS AND PROCEDURES OF IN-SITU TESTS The fully-bonded rock bolts as the mine road¬way supports were tested in the Fukasawa mine which is located in the northeast district of Japan (Fig. 1). The Fukasawa mine (one of the Kuroko mines) started the production in 1973, and the present monthly production is slightly less than 20,000 tons. The ore deposit which exsists at about 400 m depth is divided into several small lenticular shaped bodies. They are distributed apporiximately 1500 m in NW-SE direction and 700 m in NE-SW direction. The hanging wall is basaltic lava and the footwall is tuff. The rocks surrounding the ore bodies are soft but relatively intact, so the trackless mining system has been adopted from the beginning of the development.

Jan 1, 1982

By B. Anameric

Considerable effort has been directed towards understanding the carbothermic reduction mechanisms of self-reducing, fluxing dried green balls to produce pig iron nuggets. Given the geometry of the situation, some investigators believed that the shrinking core model was applicable. Hence, this study involved investigation of the applicability of the shrinking core model to pig iron nugget production. The experiments involved heat treatment of dried green balls utilizing either a laboratory-scale resistance box furnace or a gas-fired muffle furnace at various furnace temperatures and residence times. The products were analyzed for the following: (i) preferred reaction pattern, (ii) distribution of the metallized areas, (iii) % iron content variation in the pig iron nuggets from surface to center, (iv) carburization pattern and (v) physical and chemical properties of the pig iron nuggets. It was determined that the reduction of iron oxide occurred simultaneously throughout the sample and not beginning at the surface and propagating inward; thus the shrinking-core model was not applicable. Heat transfer and gas diffusion from surface to center were not the rate-limiting steps for reduction and carburization reactions.

Jan 1, 2011

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

By S. J. Lefond

Most people, when Borates are mentioned, mentally visualize the famous twenty mule team (really eighteen mules and two horses), trudging across the Mojave Desert or "she burns green Rosie, we are rich." Actually, however, the first use of borax was prior to Babylonian times. Their emissaries had orders to bring borax Iron the Gobi desert for use as a flux by the Babylonian goldsmiths. The borate mineral imported for this is not known but probably was borax. The ancient Persians and Arabians knew about borax and the Arabic word "Baurach" appears in a two thousand year old manuscript. The Sanscrit word for borax was tincana which has been corrupted to tincal. The Chinese were using borax as a glaze in three-hundred B.C. Marco Polo brought the first borax, along with gunpowder and spaghetti, from Mongolia to Europe in the late 1300's. Borax from Tibet was imported to Europe for nearly 500 years. In 1772 boric acid (sassolite) was discovered around Tuscany, Italy as a precipitant from volcanic steam vents. Production of boric acid started there about 1815 and provided the sole competition to the borax from Tibet. Borate deposits in Turkey have been known and exploited on a small scale since the 13th century. It is only recently that the operations are being modernized and production increased. About 1836, borax minerals were found in Chile and Argentina with borax production starting in 1852 in Chile and in Argentina in 1886. During the latter half of the 19th Century, Chile was the principle world producer of borax.

Jan 1, 1980