Search Documents

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By D. W. Gillmore

Numerous orphaned strip mines and old refuse piles scar the landscape, contributing to stream pollution and degradation of the natural environment. Field experiments to reclaim acidic surface-mined spoil and refuse banks with fly ash from bituminous coal-fired powerplants were conducted at several sites in West Virginia. Fly ash served as a neutralizing agent and soil amendment, permitting vegetation of waste lands and disposal of large quantities of ash. Reclamation of land by this method is estimated to cost about $300 per acre of leveled site, depending upon the topography of the land and quality and availability of the fly ash.

Jan 1, 1972

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By C. Y. Chen

Public Law 75-87, the Surface :mining Control and Reclamation Act of 1977 (SMCRA), Section 516(b) requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence causing material carnage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, except inn those instances where the mining technology used requires planned subsidence in a predictable and controlled manner . . .?. The Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a Federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features and also summarizes some of the measures which have been used to minimize the possibility of damage to surface structures as a result of subsidence due to underground coal mining.

Jan 1, 1981

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979

By X. F. Wang, K. B. Fu

"We investigated experimentally and theoretically the adhesion behavior of Acidithiobacillus ferrooxidans (At.f6) to different copper sulfides. The adsorption experiment showed cell densities of 10.74 × 106, 8.06 × 106, 3 × 106, 4.24 × 106 and 2.35 × 106 cells/cm2, respectively, on the surfaces of djurleite, bornite, covellite and chalcopyrite. The order was: djurleite > bornite > covellite > chalcopyrite. The results indicate that A. ferrooxidans has high affinity to adhering to the surfaces of djurleite and bornite in the acidic region. But the thermodynamic approach predicts that there will be no attachment of At.f6 to the surfaces of bornite, covellite and chalcopyrite. This discrepancy is due to the inadequate description of electrostatic interactions. The DLVO approach shows attachment of At.f6 to the surfaces of djurleite, bornite and covellite, and repulsion between At.f6 and chalcopyrite. The DLVO approach can explain the differences of the adhesion of At.f6 to different copper sulfides.IntroductionThe bioleaching of low-grade copper sulfides is a developing technology, and has been applied successfully to the extraction of copper from secondary sulfide minerals (Watling, 2006; Pradhan et al., 2008; Akcil and Deveci, 2010). The bioleaching of chalcopyrite is still a major challenge (Bosecker, 1997; Brierley and Brierley, 2001; Ehrlich, 2004). A study conducted at Billiton Process Research showed the following preferential order of sulfide minerals leached by mesophilic cultures: chalcocite > bornite > cubanite > covellite > pyrite > enargite > carrolite >> chalcopyrite (Dew et al., 1999). The bacteria can solubilize the valuable metals from the orebodies by the oxidation of minerals. Bacterial adhesion plays a critical role in the bioleaching processes (Chen et al., 2008; Harneit et al., 2006). Generally, bacterial adhesion can be explained by surface thermodynamics and the extended DLVO theory, in which the adhesion energy between the bacteria and mineral is calculated as a function of the separation distance (Sharma, 1999; Bos et al., 1999; Sharma and Hanumantha Rao, 2002). These methods take into account Lifshitz-van der Waals interactions, electrostatic interactions and acid-base interactions (Busscher et al., 2010). These interactions are very well understood and formulated in mathematical equations. The most important inputs in these calculations are surface energy, surface charge, electron donation and electron acceptance on the bacterial cell surface and mineral."

Jan 1, 2015

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By Nicholas Chlumecky

A practical method is described for determining or checking whether underground supports such as props, posts and mechanized longwall supports have bearing areas of proper size in relation to the type of ground or floor strata on which they are standing, It is felt that this information provides an approach to eliminate, as much as possible, a potential grave source of error during the selection of roof supports. This would also affect the choice of costly mechanized longwall equipment where it is possible that the size of the bearing area is not as carefully determined as, for instance, the design strength of structural components.

Jan 1, 1967

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By G. H. Lewis

This work was completed in a 440 KW pilot-scale combustor in preparation for a 50,000 Kg/hr industrial steam boiler limestone injection test program. The main objectives of the work were to: (1) identify the variables which affect sulfur capture, (2) determine the maximum sulfur removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. The variables which were identified as being important in sulfur capture were: Ca/S molar ratio, flue gas temperature at the limestone injection location, and limestone particle residence time. The maximum sulfur dioxide removal was 72%. The addition of limestone increased the particle deposition rate in the combustor; however, all deposits were easily removed by an air lance.

Jan 1, 1985

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By William Gleason

"Sluggish prices for commodities and a glut of oversupply of many commodities did not stop the world’s largest mining equipment makers from showing off their latest and greatest machines and technology starting with the world’s largest equipment trade show, bauma 2016 in Munich, Germany.From April 8-14, an estimated 580,000 visitors from 200 countries visited the show that featured 3,423 exhibitors from 58 countries. While primarily a show for construction equipment, the mining footprint has grown over the years. Among the largest exhibits was that of Liebherr, which brought more than 100 products, had an outdoor exhibition stand, a stand for the components division and a career stand under the motto “Be Part of Something Bigger.” One of the biggest aspects of the exhibit was its mining products where the company staged the first-ever professional table tennis match in the 130 m3 (170 cu yd) dump body of the T 264 mining truck. The top German players Timo Boll and Patrick Franziska with their trainer Jörg Robkopf faced Austria’s singles world champion from 2003, Werner Schlager, and the reigning Team Europe champions Chen Weixing and Stefan Fegerl.“Bauma 2016 was an absolute success for Liebherr. With this year’s appearance we were once again able to show our innovative strength, performance and technological diversity to a very large and international audience from the industry. We conducted interesting discussions with numerous customers and partners from various countries and discussed new projects,” said Stefan Heissler, Member of the board of directors of the Liebherr Group.Likewise, Caterpillar, the world’s largest maker of construction and mining equipment had a large presence at the show with more than 60 products and 12,000 m2 (129,000 sq ft)of exhibit space. Among the iconic yellow mining equipment that was on display was the 6015B hydraulic mining shovel."

Jun 1, 2016

By Timothy P. Smirnoff, Anthony Stirbys, Amanda Elioff

The construction of the continuing expansion of the Los Angeles Metro System has required the construction of eight new station structures. One contractor proposed, as a construction alternative for the support of excavation of the Hollywood/Vine Station, the use of soil-mix walls instead of the conventional soldier piles and wood lagging. Soldier piles and shotcrete or wood lagging support systems had been generally used on the other sub-way station excavations constructed to date throughout the system. Immediately east of that station and in almost exactly the same geology, the Hollywood/Western Station was being excavated at the same time using a conventional support system. This paper com-pares the performance of these two support systems in the alluvial soils of the Los Angeles Basin.

Jan 1, 1997