Search Documents

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

By M. Tapper

If one considers that prehistoric man's first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

By Jianping Zuo, Chunlei Zhang, Yong Zhang, Shouyang Gao

To study the fracture evolution of overlying strata for ascending mining in a short-distance coal seam group, a two-dimensional physical simulation model was designed based on a specific geological condition. The fracture development zone was divided into the compaction zone and active zone by monitoring and analyzing the macro fracture evolution of the surrounding rock mass during the excavation of multiple coal seams. The secondary fracture development process of the overlying strata was demonstrated with a physical model. The quantity, length, and inclination of the fracture were calculated with MATLAB software, and the results were verified by geological radar. The total number of fractures between two coal seams increased with a “parabola” shape during the excavation of the lower coal seam, the crack angle was mainly vertical and horizontal, and the number of horizontal cracks first increased and subsequently decreased; the excavation of the upper coal seam caused the secondary fracture development process of the overlying strata, and the relief range and its extent increased. The mining-induced cracks from the lower and upper coal seams connected with each other, especially the permanent vertical fracture in the cutting room side and face side. Finally, the three-dimensional gas fissure was formed.

Nov 24, 2020

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By J. Philip Bromberg

Any effectuation of a viable program of air pollution control will' require a basic understanding of the chemistry of atmospheric processes, the fate and migration of SO2, and the ultimate health effects of the sulfur oxides themselves. The migration and ultimate fate of Sop discharged into the atmosphere will be discussed with particular emphasis on the various conflicting views and how these relate to our present emission control regulations. Our present lack of knowledge is a severe detriment, and consideration will be given to those particular areas where future research may best be directed to provide the answers to a number of perplexing questions.

Jan 1, 1976

By P. R. Taylor

Three refractory gold concentrates have been tested to evaluate the effect of roasting with hydrated lime followed by cyanidation. The results indicate that it may be possible to roast in such a manner as to contain nearly all of the sulfur, arsenic and antimony in the roaster calcine. Cyanidation results indicate that the gold recoveries are greater than 80% for all three concentrates.

Jan 1, 1993

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

An incremental-analysis-based stope design and cutoff grade calculation method was developed for an underground metal mine project. Traditional stope design methods are typically very time consuming and lack consistency and accuracy by manually drawing stope shapes. For quick reserve calculation and economic analysis, a new method named "3D incremental analysis based stope design" was created for mine-wide stope designs. The key idea of this method is to replace engineers' manual checking of each incremental ring with one calculation of all the rings, and to build the final stope shape with the maximum values. This process was realized through a 3D ring grid setup and proper naming conventions for rapid calculations. With this unique but practical method, multiple options for a mine design were completed within a short time before the final selection of optimal cutoff grade and best stope designs for the project.

Jan 1, 2012

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By J. Platt

Debate over acid rain legislation has presented a moving target for coal and utility company planners attempting to figure out how legislation will affect their business environment. In spite of disagreement among experts, the prospect for continued change, and persistent --perhaps even growing --uncertainty, a great deal has been learned about coal market dynamics. This paper reviews progress and describes some of the major problems and controversies.

Jan 1, 1990

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended' to a greater variety' of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age' of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By S. Frimpong, E. Siami-Irdemoosa, S. R. Dindarloo

"Electric and hydraulic shovels are the dominant loading machinery in surface mining operations. Despite their critical role in production and their high capital and operating costs, no reliable and comprehensive quantitative performance metric is available. In this paper, a stochastic shovel effectiveness (SSE) measure is proposed for the purpose of quantifying the performance effectiveness of these shovels. The SSE is based on the widely used method of overall equipment effectiveness (OEE) in the manufacturing industry. The OEE measures the performance effectiveness of equipment by multiplying its mechanical availability, utilization and production quality. In manufacturing processes, quality rate is the ratio of the total number of products minus the number of defective products – equivalent to the number of acceptable products – to the total number of products. The SSE similarly uses the mechanical-availability and utilization terms, but instead of quality rate it uses a new parameter named bucket rate.The variability or randomness of the input data, that is, availability, utilization and bucket rate, are further incorporated into the SSE, and a final stochastic SSE distribution is derived in the form of a probability density function. One hydraulic and one electric shovel in a surface mining operation were selected to test the validity of the proposed method. The SSE scores for the two shovels, operating continuously for one year, were derived and compared. As with the OEE, the three-parameter SSE method yielded more representative results for overall performance measurement than a single-parameter approach. Using Monte Carlo simulation, a three-parameter Weibull and a normal distribution were derived for quantifying the overall effectiveness of hydraulic and electric shovels, respectively. As a decision aid, the proposed methodology promises to render a more informative tool than traditional metrics for mine equipment maintenance and management."

Jan 1, 2015

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.