Search Documents

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL

The steepness of an openpit mine’s slopes has a substantial influence on the mine’s financial return. This paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross section within each rock layer: that is, the profile inclination across each layer tends to be constant. Here, instead, a new geotechnical software, OptimalSlope, is used to determine optimal pitwall profiles of depth-varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and factor of safety (FoS).

By Steve Skelhorn, Dan Ifrim

"A tunnel project poses many challenges; the operation of the Tunnel Boring Machine (TBM) being one of them. Mechanized tunneling is known as a safe and effective alternative to other methods in terms of schedule and cost; however, efficiency can be severely affected by a bad TBM selection and qualification and employment of inexperienced operators. The success of a mechanized tunneling project involves a comprehensive and interdisciplinary consideration of all contributing factors such as TBM technical specification and selection, TBM design and procurement including ancillary equipment and tunnel linings. The tunnel equipment selection along with the operation can make or break the project. The objective of this paper is to address the importance of the skills and qualifications of the TBM crew with particularity to the TBM Operator. The study includes the Owner and Consultant involvement in the selection and pre-qualification of the TBM crew and specifically the TBM operator as well as the role of Contractor and TBM manufacturer in TBM operator training. This paper also analyzes the possibility of issuing a TBM operator certification, and discusses the benefits and significance of periodic training and certification programs. INTRODUCTION Training in the tunneling industry is not a new topic. The industry continues to evolve and become more complex with technology advances and expansion of mechanical tunnelling to mechanized shaft construction, large diameter drilling and mining industry applications. The need for professionals trained to operate mechanized tunnelling equipment is ever increasing, while there is a significant number of veterans who will be ageing out in the next 5 years. Consequently attracting young professional is a very important aspect of sustaining a qualified pool of professionals. For any given tunnel project, the owner and the engineer spend up to several years, studying the ground conditions during preliminary and final design. Post contract award the contractor spend additional months studying the ground again to develop the optimum means and methods for construction. All this time and money spent at the beginning of the project has the purpose of developing the optimum tunnel design, assessing the risk associated and implementing mitigation measures to reduce risks to acceptable levels. Following the tunnel design process, sophisticated TBMs are being specified and sourced to ensure the best tool for the job. The question raises here: Are there available experienced/trained professionals capable of operating these sophisticated machines?"

Jan 1, 2016

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By Peter Kowalczyk

Magnetic surveying and map production is well established in land based mineral exploration. Magnetic data are routinely used to map geology in covered terrains, to estimate the depth to basement in overburden covered areas, and to identify altered zones, mineralization, bedding attitudes, and fault networks both regionally in map view, and through interpretation to depth in 3D. Best practices for magnetic survey methods and magnetic interpretation exist in all areas of land based geophysical survey methodology - mineral exploration, hydrocarbon exploration, geological mapping, archeological mapping, and in military applications. At sea, and particularly under the sea, sophisticated magnetic surveys are being done, but it can be argued that these are primarily in niche applications, for example in naval mine-hunting and UXO applications. Magnetic data is not normally collected on AUVs and ROVs conducting mapping and hydrographic survey operations. OFG has developed physical and mathematical calibration routines so that magnetometers can be mounted directly onto AUV and ROV bodies where significant heading errors and magnetic gradients exist. This simplifies the routine deployment of magnetometers on AUVs and ROVs for mineral exploration and other magnetic survey applications without the need for towed bodies, ungainly mounting frames, or degaussing of the survey equipment. Our experience shows that magnetometers can be operated routinely on AUVs and ROVs and that with careful processing useful maps can be produced routinely at low cost.

Sep 1, 2014

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By Robert C. Freas

While on the surface limestone marketing may appear mundane, it has continued to provide a series of challenges beyond the realm normally envisioned with this industry. This paper presents a case history of a mature and well-established quarry company that has attempted to keep pace with an ever-changing economy. It examines the impact of socio- economic and technological factors on the company's marketing efforts, and looks at the role of both short and long range planning. The realities which have had to be faced and how product requirements have been kept in balance with production restrictions are also discussed.

Jan 1, 1981

By Irving D. Cohen

In order to overcome our reliance upon foreign energy sources for both crude supply and finished products, we must realize the goals proposed by Project Independence. In general this involves expanding production of existing and new oil, gas, and coal resources, utilizing and improving nuclear technology and the developing of new energy sources such as solar, geothermal, oil shale, tidal, wind and stimulation techniques. There is a continuing debate, both in the scientific community and the consuming public as to the potentiality of nuclear power generation being cost effective and environmentally and safety conscious. The development of new sources of energy does not occur overnight; it is rather a continuing effort in time and money to achieve the goal of providing energy to an ever increasing demand. The public has been accustomed to the availability of energy whenever and wherever it was needed. The era of "energy gluttony" has begun to fade into the realm of "energy awareness". Unfortunately, it required the action of another country to bring the picture that has been discussed many times in the past by energy suppliers into correct focus. Nevertheless, the public responded by conservation efforts to reduce energy wastefulness. Still, the demand for foreign importation of energy supplies is on the rise. What is our recourse? The largest known unexploited energy resource available in the United States is our coal resources. Moreover, the Department of the Interior has noted that 63 counties in Montana, Wyoming, and the Dakotas hold 60% of the nation's least expensive strip minable coal. This western coal is the most abundant and least costly Fossil Fuel in the United States. It is acknowledged that western coal is an important input in meeting the energy needs of our nation.

Jan 1, 1976

The Coeur Rochester Mine is one of the largest and lowest cost primary silver mines in the United States. In January, the mine surpassed 3.1 kt (100 million oz) of historic silver production. Rochester is owned and operated by Coeur d’Alene Mines, the world’s largest primary silver producer. Rochester is the world’s seventh largest silver mine. It also produces gold — more than 31.1 t (1 million oz) in historic production. Cash operating costs have averaged 8 cents/g ($2.58/oz) of silver since operations began in 1986.

Jan 1, 2004

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008