Search Documents

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By Paul S. Goodman

This report examines the feasibility of Employee Assistance Plans for the coal industry. Three issues are examined in detail. First, the prevalence of off-the-job factors such as alcoholism, drug abuse, and marital problems are examined in a sample of miners from the eastern, midwestern, and western underground coal fields. Then data were presented that examined the link between these off-the-job factors and behaviors critical to the mines such as absenteeism and turnover. Lastly, we examined the effectiveness of the major Employee Assistance Program in underground coal mining--the HELP Program. The report contains recommendations on whether coal mining companies should implement these programs and how these programs should be designed.

Jan 1, 1986

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By E. C. Lane

["_&apos;_-is is t`-e tenth in a series of retorts on proferties of cornmerci-al motor fuels, m,-_de in accord^nce ::ith a cooper: tine aSreement between the Cooperative Fuel scorch (C.F.R.) Committo e ^nd the. PPure__u of Mines of the United_ States De_nartr.ent of the Interior. Zee first report rave data. on motor gs.solir_es sold. during .e winter of 19,-"1-3b. e are ent report presents an^..lytico1 data f&apos;i&apos;r samples, rerrerentin_E, t:-.e products of apyroximately 90 conr.anies, hich, as in previous surveys, include both lame and stall surnliers. In ?_"dition, the Pacific coast is represented by data that were avera,;el ty the Pacific Coast Technical Group before bein submitted and are rublisi,ed exectly zis they were received. As in previous s?nrve,rs, the data r~Lre divided into the three groups of samples of regular-price, premiu::--trice, and third-grade gasolires, and each group has been averaged sel c~r~.tely. he number of nmtles, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as folio:;s: Reg<.~-lar price, 934 ca.^rnles, 2c0 i to s, and ~0 brands; premium price, 460 saris les, lPitems, an&apos;. -C` brat&apos; i _~ t__ rd grade gaseline, 360 samples, 177 i te.^..s, and of these terms as _ised in the surveys are a:: follows:]

Jan 1, 1941

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

The Bureau of Mines human factors research program is directed toward reducing accidents and improving the overall efficiency of the person-machine environment interface found in surface and underground mines. The focus of the hum factors program therefore, is to insure that sound knowledge is available concerning human capabilities and limitations, and that this knowledge is applied to the design, of mining equipment, work tasks, and management procedures. The papers presented in these proceedings summarize some of the recent Bureau research in hum factors. The papers focus on two broad areas, human resource issues and human engineering of equipment, tools, and work procedures found in mines.

Jan 1, 1987

By H. H. Dewing

The Bureau of Mines constructed a process research unit (PRU) to demonstrate new technology for extracting zinc from sphalerite concentrates. Up to 9 kg/hr of sphalerite (ZnS) concentrate was reacted at ambient pressure in the PRU with 80 pct sulfuric acid at 160° to 180° C to produce zinc sulfate and elemental sulfur. The PRU consisted of a three-stage glass reactor system: a 4-liter premix stage in which feed was slurried with 78 to 82 pct H2S04, a 40-liter stirred reactor, and a ISO-liter settling stage in which high reaction conversions were effected and excess H2S04 for recycle was separated from insoluble ZnS04 and sulfur. Evolution of sulfur-containing gases was minimized by sub-surface addition of acid feed slurry to the stirred reactor and by exclusion of air from the reactor to prevent the oxidation of elemental sulfur. Conversion of zinc to zinc sulfate averaged over 99 pct at the optimum acid concentration of 80 pct. Total sulfur losses (primarily S02) were less than 2 pct of the sulfur in the sphalerite. Elemental sulfur remained in the insoluble portion of the settled reactor product after leaching with simulated spent zinc electrolyte containing sulfuric acid. The sulfur residue contained 75 to 89 pct sulfur. Neutral zinc sulfate, required for zinc electrowinning processes, was separated from the sulfuric acid leach solution by crystallization at -15° C as zinc sulfate heptahydrate (ZnS04?7H20). The crystallization operation simultaneously effected a partial concentration of the recycled electrolyte solution by removing water.

Jan 1, 1982

By Parviz F. Rad

This Bureau of Mines report reviews laboratory and in-mine techniques for determining mechanical properties of coals, with special emphasis on the relationship between these properties and the minability of coal. An extensive bibliography is included.

Jan 1, 1973

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976