Search Documents

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By C. W. Smith

The Bureau of Mines conducted physical and chemical beneficiation studies on three samples of waste investment casting molds to devise a method to liberate and recover zircon. Rod mill grinding, autogenous attrition grinding, and caustic leaching were liberation methods inves-tigated. Flotation, gravity separation, and caustic leaching and sizing were recovery methods investigated. Flotation techniques produced con-centrates containing up to 74.2 pct zircon with a zircon recovery of 53.4 pct. Gravity concentration produced concentrates containing up to 98.6 pct zircon; however, recovery of the zircon was only 57 pct. Caustic leaching and sizing produced concentrates containing up to 98 pct zircon with attendant recoveries of 81 pct.

Jan 1, 1985

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By L. A. Stewart

This is one of a series of reports prepared by the Federal Bureau of Mines on mining methods, performance, and costs at individual mines in the United States. The primary purpose of these papers is to promote development and conservation of our mineral resources by disseminating technological information on methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. This report discusses the highly selective mining methods of the Jaquays Mining Corp. at the Regal asbestos mine, 45 road miles northeast of Globe, Ariz. The milling method at the Globe plant is discussed briefly, and the extraction ratios of the various grades of fiber are tabulated. The proposed flowsheet of a new mill under construction is shown.

Jan 1, 1961

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By D. E. Welcome, T. W. McDowell, R. G. Dong, S. F. Wiker

Workers using vibrating hand tools have the potential for developing health problems associated with repeated forceful actions and exposures to hand-transmitted vibration. Hand-arm vibration syndrome (HAVS) and other hand-arm system disorders have been associated with such exposures.1-2 To better assess health risks, comprehensive evaluations of these exposures must include quantitative assessments of hand-tool coupling forces; unfortunately, no standardized method for quantifying hand forces exists. Handle instrumentation may be ill-suited for some field environments. Psychophysical force-recall techniques may provide alternatives to handle instrumentation. A thorough understanding of the effects of vibration and other factors on force-recall accuracy and reliability is important before such methods are applied in risk assessments. Methods In this study, the effects of vibration and other factors on the accuracy of psychophysical force-recall were explored in two experiments. Twelve male subjects participated in the first experiment. The second experiment employed 20 participants (10 female, 10 male). In each experiment, participants applied specific grip and push forces to an instrumented handle mounted on a shaker system. Participants were exposed to sinusoidal vibration at frequencies that ranged from 0 Hz to 250 Hz. Three levels of applied force (low: grip = 15 N/push = 25 N, medium: grip = 30 N/push = 50 N, and high: grip = 45 N/push = 75 N ) and two levels of vibration magnitude (low: ANSI 4-8-hr limit and high: ANSI <0.5-hr limit)3 were examined. During the vibration exposure period, participants were provided with visual feedback while they attempted to “memorize” the applied grip and push forces. At the conclusion of the vibration exposure/force memorization period and a controlled rest period, the participants tried to duplicate the grip and push forces on a non-vibrating handle without the aid of visual feedback. The effects of different vibration frequencies, vibration magnitudes, and grip and push force levels were tested in a random order from trial to trial. Results Participants tended to overestimate grip and push forces. Depending on exposure conditions, error means ranged from 2 N to 10 N. The ANOVA revealed that force-recall errors for exposures between 31.5 Hz and 63 Hz were significantly higher than those at other vibration frequencies (p < 0.05). The frequency effect is depicted in Figure 1. Error means were greater when participants were exposed to the higher vibration magnitude (mean = 9.1 N, 95% CI = 8.2-10.1 N) when compared with the lower vibration magnitude (mean = 4.9 N, 95% CI = 3.9-5.8 N) (p < 0.05). The effect of vibration magnitude is shown in Figure 2. The average error for

Jan 6, 2006

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Kathleen M. Kowalski-Trako?er

National Institute for Occupational Safety and Health re­searchers conducted a study to investigate the human response issues related to wearing a self-contained self-rescuer (SCSR). The goal was to develop training to educate miners on what they could expect from their units during an escape. Subjects included miners who had experience wearing SCSRs, manu­facturers, and researchers. Results identified nine key areas of concern: (1) starting the unit, (2) unit heat, (3) induction of coughing, (4) unit taste, (5) difficulty in breathing while wearing the unit, (6) quality of the air supplied, (7) nose clips, (8) goggles, and (9) the behavior of the breathing bag. In addition, researchers reviewed the literature on human response under duress. This article describes the expectations training program, which comprises the findings of the SCSR study and what is known about the normal human response in an emergency. The authors present background on SCSRs and the SCSR switchover procedure mandated in the recent federal Mine Improvement and New Emergency Response Act of 2006, which provided the impetus for the expectations training. Keywords disaster, escape, mining, self-contained self-rescuer, training

Jan 1, 2008

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By Gerald T. Homce, James C. Cawley

Problem: CFOI and SOII data show that 2,287 U.S. workers died and 32,807 workers sustained days away from work due to electrical shock or electrical burn injuries between 1992 and 1998. Method: The narrative, work activity, job title, source of injury, location, and industry for each fatal electrical accident were examined. A primary causal factor was identified for each fatality. Results: Electrical fatalities were categorized into five major groups. Overall, 44% of electrical fatalities occurred in the construction industry. Contact with overhead power lines caused 41 % of all electrical fatalities. Discussion: Electrical shock caused 99% of fatal and 62% of nonfatal electrical accidents. Comprising about 7% of the U.S. workforce, construction workers sustain 44% of electrical fatalities. Power line contact by mobile equipment occurs in many industries and should be the subject of focused research. Other problem areas are identified and opportunities for research are proposed. Impact on Industry: Improvements in electrical safety in one industry often have application in other industries.

By Paul C. Turner

The U.S. Bureau of Mines, through an Interagency Agreement with the U.S. Army Tank-Automotive Command (TACOM), has successfully developed a steel expendable pattern casting process (EPC) for the manufacture of armorplate. The new armor is lighter and more ballistically effective than conventional rolled homogeneous armor (RHA), and costs less. An applique armor spinoff from the program was field-tested during the Gulf War. The applique armor withstood direct impacts from enemy munitions without failure.

Jan 1, 2010

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963