Search Documents

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By T. Kessler

As part of a respirable mine-dust research program at the U.S. Bureau of Mines, spark-source mass spectrometry has been used for the semiquantitative determination of trace elements (200 ppm weight or less) in raw coals. In addition, several minor and major elements have been determined using this technique. Sixty-four elements ranging in concentration from 0.01 to 41,000 ppm weight were determined in one anthracite, two mvb, four lvb, and six hvab raw coal samples. The samples represented 10 coal seams located in Pennsylvania, West Virginia, Virginia, Utah, and Colorado.

Jan 1, 1973

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

By A. B. Coates

During the last three years the use of ethylene glycol dinitrate4 (E.G.D.) as at low-freeze (L.F.) agent in place of nitropolyglycerin has become common in the manufacture of explosives of the dynamite type. The usual proportion of D. G. D. in the explosive "oil" is 25 per cent; the remainder, 75 per cant, is regular nitroglycerin. These proportions were probably selected as a continuation of the practice of 25 per cent nitropolyglycerin and 75 per cent regular nitroglycerin.

Jan 1, 1929

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By M. J. Ferrante

Relative enthalpies of CuBr from 298.15 to 1,301 K were measured at the Bureau of Mines to provide thermodynamic data needed for the advancement of mineral technology. The temperatures of transition were measured by differential scanning calorimetry (DSC) and the standard enthalpies of transition[ (IlH~r) by drop calorimetry. The combined results gave reversible transitions at 657 K with llH~r= 1.10 kcal/mol, at 741 K with lm~r == 0.51 kcal/mol, and at 759 K with an enthalpy of fusion (AH~) of 1.22 kcal/moL ] An anomalous increase in heat capacity preceded the first crystal transition at 657 K. Tabulated values are listed for the standard relative enthalpy, heat capacity, entropy, and Gibbs energy function from 298.15 to 1,500 K. Standard relative enthalpies are also given in equation form and combined with thermodynamic data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1984

By Roy S. Nutter

An expert system advisor consultant to assist a coal mine section foreman is described in this report. The system is designed for an underground continuous miner section that is being specifically used for longwall development. The system provides three methods of operation that include normal operational mode for use underground, a training mode for use in training section foremen under controlled classroom conditions, and a demonstration mode that is free running. The Face Decision Support System or FDSS, is designed to interface with section environmental monitoring equipment and section production monitoring equipment that may appear in the future. This provides automated reprioritzation of the section foreman's job list from the system. The system 1S written in LASER which is written in C and is operated under the UNIX operating system. The objective of the entire FOSS system is to ensure that no job or piece of information important to safety or to production is forgotten because of the immediate problems confronting the section foreman.

Jan 1, 1988

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By Wilbur I. Duvall

Twelve millisecond delayed blasts in four limestone quarries in Iowa were instrumented with arrays of vertical velocity gages to determine if the direction of propagation through the rock or the method of initiation of the blast had any effect upon the level of vibration. Two gage arrays approximately 90° apart were used to test the effect of direction of propagation. The vibrations from blasts initiated by three methods were recorded. Vibration records from these tests were analyzed for peak particle velocity as a function of distance from the blast. The data are shown to fit a power Law equation. Direction of propagation is shown to affect the value of the exponent n. The effect of charge size per delay interval on the level of vibration is removed from the data by scaling the travel distance by the square root of the charge weight per delay period. The method of initiating the blasts is shown to have a strong effect upon the level of vibration and the spread in the data from one shot to another.

Jan 1, 1963

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By Paul M. Tyler

The colony of French Guiana ( or Cayenne ) is administered by a governor , assisted by a privy council of five members . A council - general of 16 members is elected by French citizens resident in Guiana, and the colony is represented 3 in the French parliament by one deputy . The area is about 34,740 square miles . French Guiana is the largest gold producer of the French colonies , producing nearly $ 1,000,000 worth annually . Considerable prospecting has been done on the bauxite deposits , which are extensive . Copper , iron , lead , and 4 mercury deposits are also reported . In 1931 , 10,000 prospectors for gold were reported as working . The French Government is taking an active interest and has sent a committee of mining experts to explore the region ; no permits are to be issued to individual prospectors while the committee is in the colony . Plans for development of mining industry include consideration of 4,500 convicts and 2,500 natives already in the colony and available for labor .

Apr 1, 1933

By E. J. HOFFMAN, J. c. W. FRAZER

The apparatus and methods described in the following pages were devised and used by the writers in connection with certain investiga- tions of the technologic branch of the United States Geological Sur- vey, especially those bearing on the improvement of furnace condi- tions and on efficiency in the use of fuel. The Bureau of Mines, which has charge of such analyses and tests of fuels as were formerly made by the technologic branch of the Sur- vey, is using the same apparatus and methods in connection with similar investigations that are being carried on at the testing plant of the bureau at Pittsburg, Pa. The furnace conditions prevailing both in small plants and in large industrial establishments in this country are frequently far from satisfactory. If such conditions are to be improved, they must be more thoroughly understood, and means must be found to insure complete combustion of the fuel, and yet to permit operation with such an excess of air as will result in the greatest efficiency. In this work the services of the chemist are indispensable. A very important problem is the determination of the small percentage of unburned combustible matter that escapes from the furnace in the flue gases. Under ordinary circumstances so little as 0.1 per cent of unburned combustible matter in a furnace gas is equivalent to about 1 per cent of the fuel used; and for the determination of such small percentages of gas more accurate and refined methods are required than have ordinarily been available heretofore. It is the purpose of this paper to describe some apparatus and methods which have proved satisfactory to those engaged in the chemical work of the investigations mentioned. While these methods and apparatus have been designed more particularly with regard to analysis of furnace gases, their use is by no means limited to that purpose. The reader will readily see their applicability to other uses in which the sampling and analysis of gases are involved.

Jan 1, 1911

By R. L. Marek

[An important problem in the efficient conduct of industry is that of helping the individual employee to formulate in attitude toward his work which will result in the reduction of accidents and the promotion of safety. Perhaps nowhere is the need greater for this type of psychological training of carefully selected men than at oil refineries whore both the raw materials and the finished products are highly inflammable and explosive in nature. However, the refinery organization usually is well adapted to educational safety activities -- much more so than in the producing, pipe line, and marketing departments where the personnel are more or less scattered; but the sore general principles of conduct hold true in any industrial organization. This problem of directing the attention of tie employees to their specific tasks or helping them to control and frequently eliminate hazards engendered by adverse mental attitude or emotion is met most satisfactorily by carefully selecting applicants and placing theta at jobs for which their ability best fits them. The subsequent training of these carefully selected employees to assure their Most effective work in accident prevention may be accomplished in a variety of gays, ouch as by personal supervision and instruction, inspections, drills, and by the studied use of well thought out safety pamphlets and posters.]

Jan 1, 1932

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By A. C. Fieldner, S. H. Katz

"Introduction.Recent experiments (Fieldner, A.C., Katz, S.H., Kinney, S.P., and Longfellow, E.S., Poisonous gas from carbon tetrachloride fire extinguishers, Jour. Franklin Institute, October, 1920, pp. 543-565), by the Bureau of Mines have shown that carbon tetrachloride extinguisher liquids when applied to fires produce small quantities of irritating and poisonous gases which may be dangerous in very closely confined spaces where conditions are such that the user can not escape without breathing the fumes. The results of the experiments have been confirmed in an independent investigation by the Underwriters Laboratories (Nuckalls, A.H., Corrosive action and products formed when carbon tetrachloride extinguisher liquids are applied to fires, Nat. Fire Protection Assoc. Quarterly, vol. 14, January, 1921, pp. 221-236) who conducted similar experiments for the purpose of determining the corrosive action of these fumes on metals. Both investigations showed that carbon tetrachloride vapor, hydrochloric acid gas, and phosgene were produced in addition to the ordinary products of combustion, such as smoke, carbon monoxide and carbon dioxide. The Bureau of Mines' tests were made by applying a one-quart extinguisher to a wood fire of excelsior in a gas-tight room of 1000 cubic foot capacity. The glass and metal construction of this chamber limited the experimental fire to very small dimensions. It was, therefore, deemed desirable to make a test on a larger scale in the entry of the Bureau's experimental mine in order to similate more nearly the practical use of carbon tetrachloride and other types of extinguishers in mines.Description of extinguishers.Two series of tests were made under identical conditions on different days. Commercial carbon tetrachloride extinguishers were used in the first series of tests and ""foamite firefoam"" extinguishers in the second series of tests."

Jun 1, 1921

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970