Search Documents

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By Wei Qu, Yongsheng Song, Xingyu Liu, Wenjuan Li, Shuang Liu, Guiying Zhou, Bowei Chen

The Pb,Sb,Zn multi-metal sulphide ore is processed in sequence of beneficiation of jamesonite, sphalerite . Due to relative large amount of collector (xanthate), activator (CuSO4) and regulator (lime) during different flotation stage, the flotation wastewater from sphalerite beneficiation stage can’t be directly recycled to the first lead flotation stage. In this paper, the flotation wastewater from sphalerite beneficiation stage was treated by Ozone and BAC technology, results showed that when the influent concentation of COD and copper ion were 850 mg/L, 10.48mg/L respectively, the Ozone and BAC technology could effectively treat such type of water. In the treated wastewater, the COD is 60mg/L, copper ion concentration is 0.023mg/L, pH is 7.0, which satisfy the need of Pb,Sb-Zn preferential floatation separation process. After recycle of the treated wastewater to Pb,Sb floatation circuit, qualified Pb,Sb concentrate and Zn concentrate were obtained.

Jan 1, 2014

By H. R. Manouchehri

"In mining and minerals industry, except profitability, there are some crucial factors that represent components in economic machinery of a mine and related activities. These are sustainability and minimizing environmental impact factor. Environmental concerns combined with the water and energy availability and related costs, as well as public license to operate all contrive to demand for more efforts targeting sustainability. Mining industry is highly energy-intensive (estimated to consume 6-7% of total world’s energy), with varying the energy efficiency across the industry resulting in significant costs. Size reduction is the main energy consumer contributing to almost 50% of the total energy used in mining. That means efforts must be made to introduce energy efficient comminution flow-sheets and machineries for sustainable development. Since the crushers are more energy efficient than mills, it is logic to push down-sizing in crushing stage(s) as far as technically possible. That has been strategy for Sandvik Mining and Rock Technology in supplying advanced and effective crushers to provide fine crushed product for subsequent milling stage. Lowering the energy consumption and related costs as well as increasing throughput have been the main objectives in design and development of comminution circuits and related machineries. Inefficiency in comminution technology, particularly in grinding, has long been regarded as a major area for investigation and development, especially when production of fines and ultra-fines are considered. In an attempt to explore the potential of fine crushing and its effects on subsequent milling process the fine crushing performance of Sandvik’s conventional cone crusher and Vertical Shaft Impactor (VSI) in pilot scale to define the energy consumption and circulating load in fine crushing. Tests were conducted to obtain fine crushed products at P = 2 mm in a close circuit. Furthermore, the crushed products were characterized and compared by grind-ability, morphology, and surface area measurement tests. Finally, the energy consumption to grind the crushed products to specific grind size was calculated."

Jan 1, 2018

By R. Sakthivel

Blue dust is a high grade soft haematite material containing 96.14% Fe2O3 transformed into magnetite (Fe3O4), when it is subjected to planetary ball milling in the presence of iron powder as reducing reagent. X-ray diffraction (XRD), Field emission scanning electron microscope (FESEM) and Laser particle size analyser have been employed to characterize various samples collected at various milling times to know the phase evolution, particle size distribution and morphology of particles. X-ray diffraction studies reveal the formation of magnetite phase at the optimum milling time of 40 hours. Vibrating sample magnetometry (VSM) study demonstrates, that sample obtained at 40 hours of milling time exhibits saturation magnetisation of 14.757 emu/g whereas the starting material used in this study shows only 1.0425 emu/g. Keywords: Blue dust, reaction milling, magnetite, saturation magnetization

Sep 1, 2012

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By Lj. D. Andric

Development of modern devices for mechanical and mechanochemical materials activation has been dated since the beginning of last century. Rapid development of high-energy mills that are different in type, size, design and performances, has been occurred during the last four decades. Because of complete understanding of mechanical processing, entire knowledge of theoretical principles of high-energy mills is necessary. These principles are main causales of process that are happened in materials during the mechanical activation. This paper is occupied by theoretical principles of operation of high-energy mills. Conventional high energy mills with balls, high-energy planetary mills and high-energy vibrational mills are particularly considered in the paper.

Jan 1, 2014

By Sirish L. Shah

It is now common to have archival history of thousands of sensors sampled every second over long time. Yet we frequently have process engineers complain:??.We are drowning in data but starving for information??. How can these rich data sets be put to use? This paper addresses the issue of information and knowledge extraction from data with emphasis on process and performance monitoring including fault detection and isolation. Most of the major plant, factory, process, equipment and tool disruptions are avoidable, and yet preventable fault detection and diagnosis strategies are not the norm in most industries. It is not uncommon to see simple and preventable faults disrupt the operation of an entire integrated manufacturing facility. For example, faults such as malfunctioning sensors or actuators, inoperative alarm systems, poor controller tuning or configuration can render the most sophisticated control systems useless. Such disruptions can cost in the excess of $1 million per day and on the average they rob the plant of 7% of its annual capacity. Over the last decade the fields of multivariate statistics and data visualization and analysis methods have merged to develop powerful sensing and condition-based monitoring systems for predictive fault detection and diagnosis.These methods rely on the notion of sensor fusion whereby data from many sensors or units are combined with process information, such as physical connectivity of process units, to give a holistic picture of health of an integrated plant. Such methods are at a stage where these strategies are being implemented for off-line and on-line deployment. This article attempts to outline the field of sensor fusion - the application of signal processing methods, in the temporal as well as spectral domains, on a multitude and NOT singular sensor signals to detect incipient process abnormality before a catastrophic breakdown is likely to occur Keywords: Process analytics, process and performance monitoring, multivariate statistical analysis, sensor-fusion

Sep 1, 2012

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By Jonas Addai-Mensah

Despite the fact that nickel (Ni) laterites accounts for about 60 % of the world?s nickel mineralization, commercial processing of complex, low grade Ni laterite ores by conventional beneficiation (e.g. magnetic, electrostatic and flotation separation) still presents intractable challenges, particularly in heap leaching. Invariably, low grade laterite ores require aggressive hydrometallurgical techniques (e.g., highly acidic lixiviant leaching at ambient or elevated temperatures) for Ni and cobalt (Co) extraction. As a precursor to heap leaching, agglomeration of the multi-mineral phase feed particles into robust and porous granules of 4-10 m permeable bed, is essential. In the present work, several basic and applied studies of the agglomeration behavior of real Ni laterite ores and selected oxides and clay minerals (hematite, quartz smectite and kaolinite) which constitute the predominant host gangue phases of typical laterite ores are performed. Isothermal, batch agglomeration tests involving sulphuric acid solution as a binder were carried out to produce coarse, narrow-sized (5 ? 40 mm) granules which were well characterized. The influential role of feed ore characteristics (e.g., mineralogy/chemistry and primary particle size distribution) and binder composition (30 vs. 44% w/w H2SO4) and dosage (15-25 wt.%) in agglomeration behavior and granule properties were examined through several characterization techniques including granule size, compressive strength, bed percolation and re-wetting stability and 3-dimensional micro-structure analyses. Links between feed mineralogy/chemistry and size, binder formulation, agglomeration behavior, curing conditions and final granule properties and structural characteristics are established. The implications of the findings to Ni laterite plant agglomeration for enhanced heap leaching are discussed. Keywords: nickel laterite, complex low-grade ores, agglomeration, heap leaching, micro-structure

Sep 1, 2012

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By F. Burat

The present research covers the results of experiments carried out with high frequency vibration screen on dewatering of coal fines. In the tests, the addition of surface active reagents was studied employing a high frequency vibrating screen. To increase the efficiency of mechanical dewatering processes, ultrasonic treatment was applied along with surfactants and optimum dewatering conditions were obtained. The moisture content of the feed material was from 82.5% to 41% by the optimization of operation parameters including the angle of the screen, vibration frequency, feed rate and screen opening size. Optimum parameters obtained in dewatering processes carried out with the vibrating screen were kept constant and the effects of surface active reagents and ultrasonic treatment on dewatering were investigated. Finally, the moisture level of the material was further reduced from 41.0% to 37.66%.

Sep 1, 2012

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, S. Aliferova, T. Gurkova, T. Chumakova

Cationic flotation using alkylamines and their derivatives as collectors, and characterized by high selectivity of mineral particle separation, is finding ever growing industrial application. In recent years the industrial application has been initiated of new cationic collectors - alkylmorpholines. Efficiency of cationic surfactants operation as collectors is dependent upon their colloid and sorption properties and the availability of silicate .carbonate rock-forming mineral impurities in the ore, which sorb the cationic collector. Investigations have been carried out on the influence of frothers and organic depressors with various compositions upon physical-chemical and flotation properties of alkylamines and alkylmorpholines. On the basis of these investigations requirements for organic depressor were developed and new flotation reagents were proposed (V-1 frother and KS-MF depressor). The use of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles. Data of new reagents industrial application is presented. The reagents developed can be used for flotation processing of other ores.

Jan 1, 2003

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014