Search Documents

By Thomas Mütze, Petya Atanasova, Kai Bachmann, Urs A. Peuker, Thomas Leißner

"A method is presented for the evaluation of mineral processing by liberation and upgrading. The method bases on the plot of recovery of valuables versus the recovery of gangue (Fuerstenau upgrading curve). The locking curve of a feed material was plotted together with the upgrading curve in a Fuerstenau diagram. The assessment of liberation and upgrading is done by a comparison of surfaces formed by the curves and some characteristic lines of the diagram. This plot allows the calculation of two new quantitative measures for liberation and upgrading. Both parameters can be combined to a third parameter describing the quality of the whole technical setup for mineral processing by subtracting the upgrading parameter from the liberation parameter. The third parameter shows a positive value in cases of upgrading determined processes, a negative value in cases of liberation affected processes and about zero for processes affected equally by liberation and upgrading. Thus it is easily possible to distinguish between poor results in the mineral processing caused by insufficient liberation or poor results caused by insufficient upgrading. Preliminary results from two case studies, performed on two different ore types, are very promising illustrating the practical use of such an approach."

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By M. Saghaeian, R. Hejazi, R. Barreiro, M. Tavousi, M. Ahadi, O. Asghari

"Banded iron formations are the major iron source for producing high grade concentrate. BIF are generally lower grade and more difficult to extract. In order to know how best to process BIF ore, it require comprehensive knowledge on ore bodies even in the early stages of the mining process. Geometallurgy combines geological and mineral processing information and allows for higher flexibility in response to changes in the plant feed when mining different parts of the ore. This can lead to economic benefits, owing to improved plant operation, yet is time consuming and correspondingly costly. The main focus of this paper work has been to develop a comprehensive geometallurgical testing framework for developing Yogi BIF low grade magnetite deposit located at Western Australia. In order to provide successful geometallurgical mapping, was collected data from several different disciplines (geology, chemistry, mineralogy) and parameters (physical properties, metallurgical response and geotechnical measurements) during drilling activities and test work. The investigation shown magnetic separation behavior of material had high variation and is most important element in the proper design of ore beneficiation plant. This paper provides an improved and efficient magnetic separation test methods used for the investigation of separation behavior and variability of the Yogi Ore deposit and evaluates their applicability and potential in the geometallurgical context. In this paper a small-scale magnetic separation has been developed that allows estimating from single pass separation test using small amounts of sample material. Verification of the evaluation method and validation was done with different mineral systems."

Jan 1, 2018

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By B. Peszko

There are many measuring methods of grain sizes. Taking into consideration the fine grained materials, one of the existing techniques is measurement of grain size by the Coulter Counter method. This method is based on the measuring the changes of electrolyte resistance during grains flow through the calibrated diaphragm. This method is relatively simple to apply, significantly precise and the results are given quickly. However, the problem is that the measurements are limited by the size of diaphragm. Because of this situation, measurement of grain sizes by this instrument is possible in range from 10% to 60% of diaphragm diameter. This limitation causes the necessity of re-placing diaphragm in case when the measured grain size distribution concerns the material of large size range. In purpose of determining the total grain size distribution, the synthesis of some partial distributions, given for individual grain fractions (with different diaphragm applied), is required. This is possible to do by calculating the mixture of distribution functions, created from the partial distribution functions. Two materials were selected to research: quartzite and glass, which were comminuted in cylindrical crusher, additionally grinded, screened and then analyzed by Coulter Counter for five grain fractions: 0~125 µm, 0~80 µm, 0~56 µm, 0~40 µm and 0~25 µm. For each fraction, five different partial distributions were given (in case of glass ? four), which are the basis for the creating the joined grain composition. To assure the adequacy of the given distribution function, it is necessary to obtain the possibly best approximation of partial distributions. In the work, both the parametric and non-parametric methods of density approximations of investigated random variable. For each grain fraction the approximations were done by three traditional distribution functions: RRB, GSA and log-norm distribution functions and three methods of non-parametric approximation: Gauss kernel, Epanechnikov kernel and orthogonal Fourier series method. As the criterion of the certain distribution function acceptance, the value of the residual deviation was assumed, given by the formulae:

Jan 1, 2014

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By T. Wajima

We tried to convert paper sludge ash (PSA) into zeolitic product with high cation exchange capacity (CEC) through acid leaching. Typically, PSA from incineration of paper sludge contains a high percentage of calcium in the form of anorthite (CaAl2Si2O8) and gehlenite (Ca2Al2SiO7). It is difficult to convert the ash with a high Ca content into zeolites, or at least into more desirable zeolite phases. Acid leaching with HCl was applied to reduce the Ca content to synthesize zeolitic product with high CEC. The raw ash was treated with 1 M, 3 M, and 5 M HCl solution for 0.5~24 hours (the ratio of the ash to volume of HCl solution was 1/4), and then zeolitic product was synthesized from leached ash through the reaction with 2.5 M NaOH solution at 80 oC for 24 hours. During acid leaching, gehlenite is readily dissolved in a lower HCl concentration solution than anorthite. With increasing HCl concentration, the amounts of Ca, Mg, Si, Al, Fe and Ti extracted from the ash increased. Ca and Mg contents were easily extracted from ash than other elements. The contents of Ca and Mg extracted rapidly at initial stage, and then levelled off. The saturation times of Mg and Ca are almost 0.5 h using all concentrations of HCl solutions. After the synthesis from leached ashes, zeolite-A and -P were synthesized from ash leached in 1 M HCl solution, and 3 M and 5 M HCl solutions, respectively, regardless of leaching time. With in-creasing HCl concentration, the Ca content eluted from the product decreased, due to the removal of Ca via acid leaching before the synthesis, while the Na content eluted from the product increased to 3 M HCl and then decreased, which was almost similar to the CEC of the product, due to the ion exchange of Na-type zeolitic phase in the product. The change of zeolite phases in the product and the CEC of the product depend on the concentrations of Si and Al in the solution during the synthesis. The highest CEC of the product is about 220 cmol/ kg, which was synthesized from the ash leached in 3 M HCl solution.

Jan 1, 2014

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012

By D. X. Chen

Comprehensive utilization of the copper associated with the complex lead and zinc sulphide ore is a recognized and difficult technical issue in ore dressing field. Qi Baoshan lead-zinc mine is a typical complex copper-lead-zinc polymetallic ore deposit and difficult to process. The application of the. traditional process is not able to make the substantive progress. According to its mineralogical characteristics, the association of copper minerals with lead minerals is very close, and their particle sizes are very fine, and the copper and lead minerals are partially oxidized. Based on the laboratory tests and comparison between different process flowsheets, preferential flotation of copper minerals, being suitable for this ore, was chosen to recover copper. The separation of copper from lead applies the following technology: regrinding middlings with cyclones to classify, which improves copper lead mineral liberation, and increases copper and lead recovery; using new high-efficient collector with good selectivity, which is able to float copper minerals; and non-toxic combined depressant which depresses lead minerals. The above technical innovation, optimizing the process flowsheet, overcoming the complex traditional process flow with high production cost, obtained good technical and economic indicator. The difficult technical problem of copper lead separation was solved smoothly. After successful performance of the bench-scale experiment, commercial-scale test was carried out. In industrial trial, a copper concentrate containing Cu18.60 %, Pb7.40 % and Zn2.50 % was obtained with copper recovery of 58.49%, lead concentrate quality improved largely. The process opened up an unique path for the comprehensive recovery of Cu from similar lead and zinc non-ferrous metals mineral to comprehensively recover copper.

Jan 1, 2014

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores whereas oxidized molybdenum ores, being finely disseminated and difficult to process, have not been exploited and utilized effectively. In this article the beneficiation process of a molybdenum ore occurred in an oxidized ore zone was investigated in order to provide a new way for the development and utilization of the oxidized molybdenum ores in China. The molybdenum mineral in the ore was mainly wulfenite and the associated minerals included barite, limonite, quartz and small amount of cerusite. Limonite in the ore occurred in a crust and honeycomb-like colloidal state and composed the framework for the formation of the other minerals in the ore, which filled the pores in the framework. Wulfenite was mainly fine-grained and occurred in the fine porous crust and honeycomb-like framework. The finely disseminated ore structure made the separation and recovery of the molybdenum mineral in the ore very difficult. On the basis of the mineralogical study of the ore, experiments were conducted to compare the various mineral processing methods for the beneficiation of the ore, including single gravity concentration, single magnetic separation, single flotation, and a combination of high intensity magnetic separation and gravity concentration. The results indicated that with single gravity concentration a molybdenum concentrate containing 5.85 % Mo with a yield of 11.76 % and a Mo recovery of 43.5 % was produced. With single high intensity magnetic separation it was very hard to obtain a molybdenum concentrate product. With single flotation process a molybdenum concentrate containing 7.06 % Mo with a yield of 15.14 % and a Mo recovery of 62.63 % was produced. With a combination of high intensity magnetic separation and gravity concentration a molybdenum concentrate containing 6.46 % Mo with a yield of 11.81 % and a Mo recovery of 42.11 % was produced. In conclusion, compared to the other methods the flotation process can produce more reasonable technological and economical results and is the best process for the exploitation and utilization of the finely disseminated oxidized molybdenum ore.

Jan 1, 2014

By J. A. Sweet

The issues facing graduate training in the mineral processing industry are not too different today from those that prompted the initiation of the Anglo American Platinum Graduate Development Programme (AGDP) in 2002. Graduate metallurgists in South Africa enter the industry from different undergraduate programmes at various tertiary institutions, and so the knowledge and skills of the young graduates varies. Further, the geographical expansion of the industry combined with the downsizing of business units means that there are fewer opportunities for young graduates to be mentored through their first few years on site. Anglo American Platinum chose to address these issues by implementing an intensive, structured graduate training programme for all their new metallurgical graduates, known as the AGDP. The first two years of experience of the AGDP, from the viewpoints of both graduates and lecturers, were presented to the mineral processing community at the IMPC in Turkey in 2006 (Sweet et al, 2006). From the beginning, the programme was structured in a modular fashion to include a basic technical ?toolbox? including statistics, the scientific method and sampling protocols, while the mineral processing content comprised advanced learning in comminution, classification and flotation (later extended to include hydrometallurgy). Technical communication ? both written and verbal ? was included from the start. The programme was focussed very strongly on site work (?learning by doing?), with a major integrated site campaign conducted and analysed by each cohort. In 2012 the AGDP will accept its ninth cohort into the programme. This paper describes how Anglo American Platinum and the University of Cape Town have developed and adapted the programme over the last few years, in response to the challenges of the global recession, skills retention, and the changing operational needs of the company. The programme, which was drawn up to accommodate around 15 concentrator-only graduates, now accommodates 35-40 concentrator, smelter and refinery graduates annually. The programme has also been modified to facilitate new graduates spending most of their first year on the operations. The benefits of the programme for Anglo American Platinum have been tangible, and will be discussed in the paper. Keywords: graduate training, technology transfer

Sep 1, 2012

By P. Coghill, P. Revell

"Geo-sensing is the ability to routinely measure or infer rock properties at a range of scales using non-destructive scanning devices. These devices can provide information and data flows to support integrated decision making across the minerals value chain. Geo-sensing has been used for many years in minerals exploration using technologies such as satellite imaging and airborne geophysics but to date the use of sensing technologies in between the mine and mill has been very limited. The aim of this research is to develop new mineral sensing technologies that can enable grade engineered ore streams through the rejection of low value gangue or deleterious elements either in the pit or during transfer to the mill. This paper focusses on the research and development being carried out by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and its associated members on new sensing technologies. At the start of their development these technologies were classified on the Technology Readiness Level scale at 3 (TRL3), equivalent to a proof of concept. Laboratory testing and design is aimed at progressing these sensing technologies to TRL5 which is ready for testing at an end users site. New data obtained during the laboratory testing and design phases are presented in the paper demonstrating performance specifications such as detection limits and measurement speed which can be used to infer the pod size of gangue that can be rejected at scale. Grade Engineering® and coarse gangue rejection are considered as key drivers for the mining industry to address the higher mining, processing and environmental costs associated with ore bodies with declining grades. This is an industry wide problem and the development of mineral sensors is seen as key enabling technologies for Grade Engineering® and coarse gangue rejection. The technologies presented in this paper enhance value through early decision making of ore quality and improve the overall resource value case through improved grade and throughput engineering."

Jan 1, 2018

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Y. B. Zhu

Soil reconstruction and improvement trials and vegetation experiment is carried out at Shuilong-shan acid rock waste dumps at Dexing Copper Mine in China. pH value, Cu2+, Pb2+, Zn2+, etc. concentration in acid rock drainage (ARD) is also monitored every month since 2005. The results of experiment show that: Lime and topsoil stripped from open-pit is appropriated soil improvement material. Full cover soil improvement method is suitable for flat area, contour soil improvement method and hole soil improvement method is appropriate for slope area. The optimal plant species is ligustrum lucidum Ait,Lespedeza bicolor, Paspalum notatum, Veti-veria zizanioides, Eragrostis pilos and Neyraudia reynaudian. It is the best for Arbor, shrub and grass to be arranged in pairs or groups in order to remold optimal landscape. Pilot sites, covering 3ha, is established. Vegetation coverage reaches 90% in platform area, 40% in slope area. pH value in ARD increased slightly, Cu2+, Pb2+ concentration in ARD decreased, Zn2+ concentration in ARD decreased and varied slightly.

Jan 1, 2014

Datun Concentrator currently processes complex sulfide ores in Gejiu Municipality, Yunnan Province, China. The ore contains much higher arsenic than other ores. The run of mine ore is fed to the concentrator to recover copper and tin by bulk flotation and gravity concentration, and then the other sulphides, such as pyrite, arsenopyrite, etc. didn?t get utilized and are discarded as tailings due to the high arsenic content. In order to utilize the pyrites in the tailings, a series of tests have been conducted for finding the solution of arsenic removal from high arsenic-bearing pyrite concentrates through simple flotation process. By means of orthogonal experimental design, the optimized levels and main factors have been found out for the roughing stage. Through selection of the effective in-organic depressants for the arsenic-bearing minerals, the arsenic in the pyrite concentrate can be removed to meet the requirement of sulfuric acid plant (As%=0.5%) by the open flotation process, i.e., one-time roughing and two-time cleaning.

Jan 1, 2014