Search Documents

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By Steven L. Anderson

A cut-off wall has been designed and is currently under construction along the Back Dam of the existing tailings impoundment at Red Dog Mine, Alaska. The cut-off wall, which will be in the order of 5,000 ft long and up to 150 ft deep, when complete, is being excavated using a 40 metric ton Bauer trench cutter head mounted on a Liebherr crawler crane, in combination with a closed loop slurry pumping and de-sanding system. The tailings impoundment is situated in an area of warm permafrost and high potential seismic activity. Design incorporated an assessment of rock jointing to define the final depth of the wall along the alignment requiring the use of plastic concrete backfill to address the concerns associated with potential cracking of the wall due to settlement and during seismic activity. The results of the geotechnical investigation program, particularly with respect to variation in rock hardness along the wall alignment are discussed, as are the design criteria for the plastic concrete backfill, the challenges faced during construction, including scheduling of the work with the on-going dam raise activities of the mine, and the lessons learned with respect to potential productivities and selection of cutter wheels and teeth. Also described are the requirements for and advantages of utilizing a slurry boosting system to meet pumping requirements, re-design of the plastic concrete mix to consider workability and optimization of cutter teeth configurations to reduce wear through highly varied rock hardness.

Jan 1, 2010

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By Mathew Janes

"Sheet piles remain an economic solution to many shoring problems. However, installation of sheet piling suffers high noise and vibration with conventional impact or vibratory methods or low production and high expense with push techniques. Many projects simply will not allow sheet piling due to vibration concerns.Installing sheet piles with a tunable, high frequency Resonant vibrator provides high production with imperceptible ground vibrations. Recent projects in Canada have proven the technique on production projects where vibration sensitive structures are present immediately adjacent to the sheet piling. A project in Whitehorse, Yukon required a Waterloo style impervious sheet pile barrier be driven immediately adjacent to a sensitive, large diameter sewer line. The 1800 m2 Waterloo barrier was driven to prevent hydrocarbon leachate from entering the Yukon River. Proposed driving of the sheet raised concerned as the sewer serviced downtown Whitehorse. Monitoring of the sewer during Resonant driving proved the ground vibrations to be imperceptible. Use of the Resonant Driver prevented all concern over ground borne vibration of the sewer and allowed the contractor to progress at conventional, high production while maintaining low cost to the owner.Subsequent projects continue to prove that Resonant driving of sheet piles achieves high production while eliminating ground vibration.IntroductionA complex environmental clean-up problem required a unique solution. A historic oil and fuel transfer station in Whitehorse, Yukon is located on the Yukon River. The facility has been in use since the Second World War and witnessed much careless activity. The sand and gravel site provided ease of transmission of hydrocarbon leachates directly into the Yukon River. Continued use of the site required a barrier wall be constructed to prevent hydrocarbon from leaching into the Yukon River. A short construction season and restrictive fisheries window made for a compressed schedule. Along the shoreline of the property and within the required clean up zone a large diameter sanitary sewer collector line was present that serviced the majority of downtown Whitehorse. The design called for a barrier wall to be constructed along the waterfront adjacent to the sewer with cofferdams constructed out into the Yukon River to recover contaminated riverbed soils. The coarse sands and gravels meant high hydraulic conductivity into any kind of excavation, including slurried or drilled shafts that may have been used to construct a low vibration shoring system. Conventional hammer or vibrator technology would result in high ground vibrations that risked damaging the sewer. The Resonant Driver method was selected for its ability to drive sheet piles with high production and zero ground borne vibrations."

Jan 1, 2014

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By Dean E. Harris

The realignment of U.S. Highway 95 in Sandpoint, Idaho, is being designed on a site underlain by glaciolacustrine soil that includes very thick deposits of soft, sensitive clay to estimated depths of greater than 200 m. The highway realignment will include construction of numerous embankments, mechanically stabilized earth (MSE) retaining walls, and pile-supported bridges. The area of the proposed new highway corridor also includes existing historic and commercial buildings, a railroad, sensitive environmental areas, and economically vital tourism/recreational assets. The evaluation of pile axial capacity included the use of a variety of methods, including total stress, effective stress, and empirical methods using the results of piezocone soundings and conventional borehole and laboratory tests. These methods were used along with the findings from an instrumented static loading test to design the piled foundations for the bridges. A critical factor throughout the design of the pile foundations was controlling settlements to levels that could be tolerated by the bridges. Also, because of the proximity of the pile foundations to the existing structures and the proposed new embankments, the project has required careful consideration of the potential interaction between these elements. The analysis of piles also considered the potential for settlement of embankments, drag loads on the piles, and downdrag.

Jan 1, 2003

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Roy H. Borde

The design of foundations to support overhead signs is primarily based on providing adequate resistance against horizontal wind loads. The typically used subgrade reaction model for the load-deflection analysis of laterally loaded piles and shafts has been found to underpredict the capacity of shafts with length to diameter ratios less than five. The general applicability of an improved model incorporating the influence of shear and moment resistance at the shaft base is demonstrated. The detrimental effect of ground surface slope angle on the ultimate capacity is discussed, and a design chart for estimating the magnitude of the reduction in capacity is presented. A comparison between the predicted and measured responses of nine full-scale load tests performed within this study and sixteen external tests is presented. The models described are implemented in the computer program "LTBASE".

Jan 1, 1988

Jan 1, 2002

By K. Rainer Massarsch

In some parts of the world, vibrators are used extensively for different types of foundation engineering projects. If used correctly and in suitable soils then vibratory pile driving for example is very efficient. However, soil conditions and the installation procedure have great significance for the driving resistance and affect the bearing capacity of vibrated piles. Also the intensity of ground vibrations which are transmitted to the surrounding soil is affected by the vibration process. In spite of the increasing use of vibrators and the rapid development of vibrator technology, many aspects of pile-soil interaction are not yet understood. In order to asses the importance of factors, which govern pile installation (and extraction), it is necessary to consider the entire chain of vibration energy transmission from the vibration source to the pile, the interaction between the vibrating pile and the soil and the wave propagation in the subsoil, Fig. 1. [ ] Fig. 1. Transfer of vibration energy from the vibrator through the pile into the ground In the present paper, some important aspects of vibratory driving and their significance for pile installation and soil compaction will be discussed.

Jan 1, 1995

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989