Search Documents

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

"IntroductionIn the 1970s, environmental concerns and associated liabilities were a new and unknown aspect of corporate risk. Today, social concerns and the associated conflicts that they can generate constitute a rapidly expanding aspect of risk. Although not a new phenomena — the Bougainville copper mine was forced into closure in 1988 — social risk has emerged as considerably more important, and increasingly visible, in the last few years. Social risk is now an aspect of all mining activities which needs to be calculated into project assessments, and to be managed throughout the life of a project. While social risk has a number of aspects at the corporate level, such as company image and shareholder relations, at the level of the individual project, its primary component is social acceptability, and the principal tool for managing it is the Social Licence to Operate.Social Risk in Latin AmericaThroughout Latin America there are newly modernized mineral codes and economic systems introduced over the last ten years which, together with new environmental legislation, look very much like regulations in developed countries. To the corporations, the existence of these instruments means that the risks from the environmental issues associated with the project are known; they are legislated, defined, quantifiable and hence manageable.It seems ironic that, just when comprehensive regulations for the environmental management of mining have been put in place throughout Latin America, there arise an increasing number of challenges to mining activities. For, in spite of the apparent guarantees provided by these new legislative reforms, communities in Latin America today are more frequently standing up and taking exception to the presence of mining companies, or the ways in which the companies are conducting themselves. The viability of projects becomes threatened because they are considered socially unacceptable, a phenomenon that we describe as social risk. These challenges are less about opposing mining activities than many people would think. Rather, they are based on an increasing desire on the part of the local population to have some measure of control over their own future, and to participate in the development process from the earliest stages."

Jan 1, 2000

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By Lin-fang Shen, Shao-jun Li, Zhi-liang Wang

"The meso-structure of real soil consists of numerous particles with different sizes, while the traditional reconstruction method of quartet structure generation set (QSGS) produce relatively uniform soil particles resulting in significant discrepancy between the actual structure and reconfiguration model. In order to remedy the deficiency, the QSGS is improved by considering the influence of porosity and autocorrelative function of soil, which make the models closer to the real soil. Based on the reconfiguration model, Lattice Boltzmann method is combined in the algorithm to conduct further simulation of fluid flow in soil pores. The D2Q9 model is applied to construct the two dimensional model for simulating mesoscopic seepage field of saturated soil by setting the non-equilibrium extrapolation scheme at the inlet and outlet boundary, and the bounce-back scheme at the soil particles boundary as well as the left and right boundary. According to the case study, the proposed program is realized to simulate mesoscopic seepage field of reconstructed soil with constant inlet seepage velocity. The results show that the seepage direction of soil is along the passage with good connectivity, therefore the permeability is controlled by these passages. The seepage velocity in such channels is faster than in bad connectivity channels. Even if the channel has larger pores, the seepage velocity is still small. INTRODUCTIONUnderstanding the seepage mechanism in porous materials is significant in both theoretical and engineering problems. As a typical porous media, soil consists of solid particles and voids, which form connected channels allowing water to flow through. Such seepage in soil exists widely among geotechnical project of slope, foundation pit, and tunnel, etc. Meanwhile, a number of engineering accidents are caused by limited knowledge of seepage characters in soil (Huang, 2006; Liu, 2013). The conventional method in describing seepage features mostly based on the parameter of permeability, which is a macro statistic mean evaluating the whole connectivity of soil. Obviously, this parameter cannot exactly reflect the details of how water flows through the inner soil structure, especially the flow velocity in local mesoscopic area, hence is unable to represent the actual seepage properties. Therefore, it is necessary to develop mesoscopic approaches to fully study the seepage mechanisms."

Jan 1, 2015

By T. Yalcin, S. Brunet

The flocculant-assisted hydrocyclone involves the addition of a flocculant to the cyclone feed for the purpose of obtaining a clear cyclone overflow, and thereby eliminating or reducing thickener requirements in tailings disposal operations. This paper describes the testing of this concept on the iron ore tailings of Quebec Cartier Mining Company's Mount Wright Concentrator. The current practice at Mount Wright makes use of conventional hydrocyclones and thickeners for the disposal of their tailings, which are generated in a spiral gravity separation circuit. The test work was conducted primarily on their cyclone overflow product which becomes the feed to the thickeners. A detailed study was carried out to determine the sedimentation properties of these tailings in terms of their response to a variety of flocculating reagents, and to varying conditions of pH, pulp density and flocculant dosage. The tailings were then processed in a laboratory hydrocyclone with the aid of flocculants. The use of a shear resistant flocculant, in particular, was found to yield cyclone overflows with low solids contents. Based on the test results obtained, a conceptual flow sheet has been proposed for the treatment of the iron ore tailings at the Mount Wright Concentrator.

Jan 1, 2004

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By W. A. Green

To those who may not be familiar with the history and organization of the Flin Flon mining property from the rime of its examination and option by the Harry Payne Whitney interests until the present start of operations by the Hudson Bay Mining and Smelting Company, Limited, this paper may give a better understanding of the property. More technical discussions are being presented to you by the men most closely connected with the various operations of the property. Location The Flin Flon mine is situated along the boundary line between the Provinces of Manitoba and Saskatchewan at approximately. 54° 45? north latitude, but largely in Manitoba. Prior to the advent of the railway, the property was quite isolated. The summer route was over a course of some 175 miles, consisting of a 125-mile boat trip from The Pas, first up the Saskatchewan river, then across Cumberland and Sturgeon lakes to Sturgeon? Landing. From Sturgeon Landing, a .16-mile portage was necessary to Camp 2 on lake Athapapaskow. From Camp 2 the route consisted of a canoe trip of 32 miles across lake Athapapaskow, up the northwest arm of Schist lake, then up Ross creek to the Company's docks, and finally a 2-mile walk to the property. The winter route was just under 100 miles in length, the difference being due to the fact that a more direct route could be followed over the frozen lakes. It went up the Saskatchewan river for a short distance above The Pas and then, leaving the river, the road followed Reeder, Rocky, and Sturgeon lakes to Sturgeon Landing, and from there over the same route as the summer one, only across the frozen lakes.

Jan 1, 1930

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By A. Khan

The purpose of this paper is to demonstrate the value of identifying and optimizing throughput constraints by utilizing a Constraint Model. This will be achieved by first understanding the overall concept of Operational Excellence, Continuous Improvement and Theory of Constraints as practiced within Vale Canada Limited. Next, the value of utilizing a Constraint Model is demonstrated by primarily identifying constraints. The applications in utilizing Constraint Models will be demonstrated, including the primary benefit of identifying constraints. The remainder of the paper will focus on how to properly setup a Constraint Model using discrete simulation (regardless of simulation software). Benefits of understanding the severity of constraints and movement of the bottleneck will be recognized. The paper will conclude with the summary of real applications within Vale Canada Limited.

Aug 1, 2013

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By S. C. Robinson

"IntroductionALTHOUGH most uranium deposits of the Canadian Shield lie along its western and southern margins, those of the Lake Athabasca region extend easterly along the north shore of the lake and beyond to Charlebois lake. The western end of this belt of deposits, in the vicinity of Goldfields, is 80 miles from the Palaeozoic contact, and its eastern end, at Charlebois lake, is 240 miles from the nearest Palaeozoic rocks.Deposits in this belt may be grouped in four districts, which are, from west to east:(1) The Goldfields district, an area approximately 20 miles square, centred on Beaverlodge lake and extending eastward from St. Joseph's point to Moose channel.(2) A small area in the vicinity of Sucker bay, which is about l0 miles east of Fond du Lac.(3) An area including Middle lake to the northwest shore of Black lake at the Nisto mine.(4) A fairly large area extending northward from the eastern end of Black lake, through Charlebois lake to Spreckley lake.HistoryThe region has stimulated interest in mining circles since the reconnaissance survey of J. B. Tyrrell of the Geological Survey of Canada in l893, who reported concentrations of iron along the north shore of lake Athabasca. The deposits were staked and re-staked up to the early 'twenties' but are too lean to form ore."

Jan 1, 1952

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932