Search Documents

King Island is situated at the western approach of Bass Strait and approximately mid way between Victoria and Tasmania. The scheelite orebodies lie within the south east of the island. Ore bearing horizons from 10 m to 40 m thick occur in south and east dipping stratiform deposits. The orebodies occur in skarn formed by contact metasomatic replacement of carbonate rocks by granite intrusives. The scheelite is deposited as fine disseminated grains in and along the margins of andradite garnets in the skarn. King Island Scheelite operates two under- ground mines from which 350 000 tonnes per year are obtained. The Dolphin mine produces almost two-thirds of the total. See Figure 1. The Dolphin orebody lies beneath the sea and an area of reclamation. The orebody is inter- sected by zones of major dislocation. A chequerboard post pillar cut and fill stoping system has been chosen to provide the necessary support to the hanging wall. Because the stability of the pillars is critical to the economic welfare of the mine, considerable attention is given to the reduction of overbreak.

Jan 1, 1977

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

By D J. Cronin

Alcoa World Alumina AustraliaÆs Huntly and Willowdale bauxite mines are located in the Darling Range of South Western Australia, which places their operations within PerthÆs surface water supply catchments. These catchments supply Perth with its highest quality drinking water. With the decreasing rainfall trend of recent years catchment yields to water supply reservoirs have reduced to such an extent that water use restrictions were necessary in Perth for 2001, 2002 and 2003. Protection of catchment water quality and water use conservation are crucial issues for AlcoaÆs operations within the Darling Range. Alcoa has been conducting bauxite mining activities in water supply catchments since the mid-1960s. During that time Alcoa has worked closely with the relevant State Government water and environmental agencies to ensure that its operations do not adversely impact catchment water yield and water quality. Monitoring and research have shown that Alcoa has the necessary environmental management systems in place to ensure it can continue to operate in a sustainable manner within water supply catchments. AlcoaÆs mines reduced the volume of water taken from public water supply catchments by 24 per cent in 2002, compared with 2000. This success has had an added benefit; Alcoa does not need to develop a new water source for its Huntly Mine. The conservation measures implemented to reduce water use include: increasing water recycling, using chemical additives for haul road dust suppression, conducting water audits, reducing water demand, monitoring water use, promoting water use targets and training staff in water conservation.

Jan 1, 2003

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By Reeves T. J, Hansen J. Y

Dense medium cyclone theory, supported by extensive experimental and plant-scale evidence, demonstrates that medium rheology (stability and viscosity) substantially affects cyclone performance in mineral applications.Two instruments have therefore been developed to allow medium stability and viscosity to be-monitored in the plant environment. The instruments are described, and examples are given of their application in full-scale plants.

Jan 1, 1989

By Dif A. E N, Abdalla MH

The effect of multiple tunnels /cavities on the stress and deformation field of the soil media was investigated by using a two dimen- sional plane strain boundary element model. The soil was considered as an elastic, isot- ropic and homogenous media. The interaction of two circular and parallel tunnels/cavities was investigated. Depth of burial, tunnel spacing and surface load width were the system variables considered. The results of this study indicated that the vertical displacements of the soil media increases by decreasing the distance between the adjacent openings, the interaction between the two tunnels/cavities can be neglected for K/D > 5, while the load width has a minor effect except in the dis- tance of D from the center line of the load and for a depth of 2D.

Jan 1, 1987

By S La Brooy, C Fountain

Throughout its history the mining industry has focused on the highest-grade deposits sited in the most convenient locations. The burgeoning global population and higher standards of living not only increase the demand for mineral products but also make it harder to mine and process them. The future will include the development of lower-grade, more complex orebodies, and orebodies in difficult locations. The industry will be expected to provide for humanityÆs needs while reducing its environmental footprint and maintaining profitability. This paper reviews some of the likely adaptations in mineral processing that will occur over the next 20 years. The challenges inherent in adapting to lower grade and more complex materials might be exacerbated by such factors as the availability of water and low-cost energy. In underground mining, higher energy costs are likely to foster further developments in underground preconcentration, especially for ores that can be upgraded at relatively coarse sizes. The adoption of underground crushing could also render material amenable to semi-dry preconcentration options such as might be achieved by the rotary classifier developed by CSIRO and being commercialised by RCR Tomlinson, or more modern versions of the hand-sorting of ore that use sensors based on colour or other suitable rock properties. The cement industry and some gold roasters have used the alternative of dry grinding and classification, which might also have a part to play in dry processing. There is also likely to be increased interest in options such as in situ leaching that further minimise the surface disturbance. Underground operations will have to balance the energy savings from reducing the amount of material brought to the surface and reduced surface disturbance against the practical limitations of installing and maintaining processing equipment underground. On the other hand, surface disturbance and energy issues in open cut operations will be balanced by potentially lower mining costs and higher overall recovery from the deposit.

Jan 1, 2008

By O Pasca, B Hogg

Consistent slag blow end point detection remains one of the challenges in the Peirce-Smith converters at Mount Isa MinesÆ Copper Smelter. Under blowing results in foaming on copper blow and carry forward of oxide skims to the anode furnace. Over blowing results in high copper losses to the slag. Both present safety issues and contribute to lower copper production. The end points of the slag making phases are assessed by inspection of a bar sample. A bar sample is a thin accretion layer that adheres to a steel bar when it is inserted into the tuyere while the converter is blowing. This method is biased and subjective, so there is heavy reliance on operator experience. The Semtech Optical Process Control (OPC) system was installed in early 2002 for converter slag blow end point detection. Initial plant trials did not improve all aspects of converter operations, and uptake by operators was poor, so the system was not used. In early 2005, the Semtech OPC system was re-visited and another short trial was conducted to evaluate the permanent use of the system for slag and copper blow end point detection. During this trial, the Semtech OPC method was found to be superior to bar sampling for slag blow end point detection. The implementation and refurbishment of the Semtech OPC system has resulted in plant improvements and given a better insight into converter operation during blowing. Oxide skim generation carried forward to the anode furnace has been shown to decrease with increasing compliance with Semtech OPC. Some of the expected improvements to converter operation were not found to be significant. Semtech OPC is now well received and utilised by converter operators. Individual paper available only. Not included in book or CD ROM Proceedings.

Jan 1, 2005

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

By J Davidson

Ion exchange using strong base resins is a well established technology for the recovery and purification of uranium from sulfuric acid leach liquors. Production of uranium at the Beverley Mine in South Australia includes acidic in situ leaching, ion exchange and uranium precipitation. The salinity present in the groundwater results in a relatively high concentration of chloride in the leach liquor reporting to the ion exchange plant. The impact of chloride on the ion exchange process is discussed in this paper. The results presented show that an increased chloride concentration in the lixiviant solution feeding the ion exchange plant leads to increased uptake of chloride by the resin during the loading cycle. At the highest chloride concentration studied (7.5 g/L Cl) chloride took up to 60 per cent of the resin loading sites. The impact of the chloride can be summarised as follows: for a given uranium concentration in the lixiviant feed solution, the uranium loading decreased with increasing chloride concentration; a consequence of decreased uranium loading is an increase in the frequency of elution, with an associated increase in elution reagent costs; and for a given elution efficiency, the uranium concentration in the barrens is expected to increase with increasing chloride concentration.A few options were examined to counteract the impact of chloride: an increase in elution efficiency was targeted to reduce the amount of uranium returning to the loading circuit; increasing the pH improved uranium loading, but this was found to also increase iron extraction; and preliminary screening of alternative resins showed that the higher the theoretical ion exchange capacity of the strong base resin, the higher the uranium loading.Work is continuing on uranium recovery from saline leach liquors, specifically investigating the performance of alternative resins.

Jan 1, 2005

Statistical frequency distributions may be used to characterize the overall variation of grade in orebodies. Special types of distribution (e.g. lognormal, log-type A) are necessary to describe skewness inthe case of rare metals. Also needed (but for the most part hitherto neglected) is the serial correlation function which describes the tendency for grades near together in an orebody to be closer together than grades at points relatively far apart.The sampling problem for orebodies is interpreted in statistical terms. Different methods are reviewed, and the effect of serial correlation discussed.A discussion is given, based on experiments and observations made by the author, of biases arising in the minei:l material by such methods as chip sampling and grab sampling due to such causes as nonrepresentative selection by the sampler.INTRODUCTIONMiners have always recognized the large element of chance in their operations. Chance is the raw material of statistical theory and, provided there is some recognizable pattern or underlying regularity in a set of data arising from the operation of chance events, statisticians are able to formulate mathematical models to study them. Mining engineers, geologists, and statisticians have gone a long way between them towards finding general statistical rules which describe the distribution of minerals and metals in orebodies, and even the distribution of orebodies over the earth's surface.These rules do not have the force of physical laws, though they obviously derive from them and have been used to throw light on them. From statistical theory it is possible to find methods of estimating from sampling some of the characteristics of orebodies which are of importance to...

Jan 1, 1962

In order to maintain an accurate survey underground, it is first necessary to connect all shafts used for the transferring of the survey to the levels below by a precise surface survey.This has been achieved at Mount Isa by a careful triangulation survey with stations adjacent to those shafts most suitably located for transferring the survey below.The precedure used is described herein.The Weisbach triangle commonly used is obtained by reading to swingirig wires, the theodolite being placed in line with them as nearly as is possible. The surveyor at the surface places the wires in the shaft as far apart as the size of the shaft will permit, with sufficient space between the wires and walls to ensure their swinging freely. The far wire is fixed in position, while the near one is movable by means of fine adjusting screws to facilitate its being brought into line with the fixed wire and the theodolite. When this is done the surveyor at the lower level is advised by pre-arranged signals and the survey can then commence.The surface portion of the survey is simple; all that is necessary being to read the angle from the backsight to the wires, measure their distance from the theodolite, and keep a check on them throughout the survey to make sure that no movement takes place.The lower portion of the survey is more difficult, the surveyor first qf all having to place his theodolite as nearly as possible in line with the wires.

Jan 1, 1953

By D R. Swinbourne, Y H. Yang

Calcium ferrite slag has gained prominence in the copper smelting industry over the last decade due to the emergence of continuous converting as an established technology. As smelters move towards processing which is higher in intensity, more efficient and more environmentally acceptable, its use is likely to increase because it has technical advantages over conventional iron silicate slag, which include a higher magnetite-holding capacity, lower copper losses to slag and a lower viscosity. Calcium ferrite is currently the converting slag of choice in the Mitsubishi process at operations in Japan, South Korea, Indonesia, Canada and Australia, and in the Kennecott/Outokumpu flash converting process in USA. However, users of this slag have experienced problems in containment due to its highly corrosive nature and low viscosity. As use of this slag becomes more widespread the containment problem will assume greater importance. Consequently, work has recently been carried out to establish the mechanism of refractory attack and devise means to retard it. This work will be critically reviewed in this paper.

Jan 1, 2000

By Liu X

The solubility of cobalt oxide in iron silicate slags has been measured at 1573 K by equilibration of silica and alumina saturated slags with liquid Co-Au-Fe alloys, and by equilibration of silica unsaturated slag with solid Co-Fe alloys, at oxygen pressures of either 10-9 or 10-10 atm (1 atm = 1.013 x 105 Pa). The activity coefficient of cobalt oxide has been calculated and compared with previous studies.

Jan 1, 1991

By Stuedel J

Starting from comprehensive programme systems for monitoring tasks of any kind, this paper follows the steps of the programme system hierarchy from top to bottom. The monitoring and control centres for entire production units, the subordinate centres, i.e. district control centres, the microcomputer based autonomous control systems, and data input by mobile terminals are discussed. To an increasing extent, the main emphasis is shifted from monitoring and control of individual machinery to optimized operation of extremely complex comprehensive systems. Network displays, for instance displays of production, transport, supply- and evacuation-networks as well as of safety systems, gain increasing importance. Personnel deployment systemsand planning networks as well as stocktaking and accounting are more and more closely linked with the above-mentioned networks. In order to keep development and application (purchasing) costs low, and to assure compatibility, the use of standard modules is to be assigned particular importance. New module developments are introduced, and the design of standard interfaces for computer and module coupling are discussed.For conclusion, a short view is given on the opinion of the line manage-ments on how future hierarchic systems should be featured in terms of individual units and overall systems, and used.

Jan 1, 1985

Mining companies around the world are seeking methods to coordinate operations between the mine and the concentrator to achieve an overall improvement in enterprise performance. In several instances very significant increases in productivity (more than 20 per cent) and profitability (more than $US 10M per annum) have resulted from such efforts. The key to realising these large benefits has for the most part arisen from improved communication between mining operations and plant operations personnel and the judicious use of new tools to evaluate alternatives for improvement and to minimise the risk of implementation. This paper presents a systematic approach to mine-to-mill optimisation . The importance of systemic thinking and systems optimisation methodologies is emphasised. New tools for evaluating operational performance are discussed. Recently reported benefits are summarised. Finally current research is discussed and projections for the future are given.

Jan 1, 2000

By Gillies A. D S, Lee A. H

Water is an integral component of a mining operation. To-date water management has received a low profile in the overall management of mining operations. To cost effectively meet the requirements of government environmental legislation the man

Jan 1, 1994

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

During the past eight years a vigorous drilling campaign resulted in large increases in the reserves of both copper and silver-lead-zinc ores.As a result the Company initiated an increased production programme.Some major capital works have been completed, others are in progress and more are needed to achieve the proposed daily throughput of 14,400 tons. The increased ore potential justified a copper refinery which has been constructed at Townsville. The increased production rate achieved to date, combined with improved techniques and greater mechanization, is assisting the Company to combat the general inflationary trends caused by increased costs for labour and materials.INTRODUCTION"Today we are armed with better weapons in our fight for lowered costs and greater efficiency, but we must not flag in our efforts to improve." Such was the resolution expressed by Mr. K. B. Gross, then General Manager of the Company, in his review lecture delivered to the First Ordinary Meeting of The Australasian Institute of Mining and Metallurgy at Mount Isa on 18th August, 1952. This present review of the period 1952 to 1960 records our efforts to fulfil this resolution. At the th:ne of Mr. Gross's statement,copper production was commencing in earnest. Although the importance of Mount Isa's copper orebodies was well recognized, the major discoveries which led to Mount Isa's emergence as Australia's premier copper mining and smelting operation were not known. These ore discoveries and their subsequent development are the major factors which warrant a further review of the Company's progress.The increased magnitude of the Company's operations is illustrated on graphs of Tons of Ore Treated (Fig. 1), Metals in Products (Fig. 2), Water Consumption (Fig. 3)...

Jan 1, 1961