Search Documents

By Lawson F

A rotating disc geometry has been used to provide a uniformly accessible surface for a kinetic study of the cementation of the metals cadmium, lead and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu/Zn and Cu/Fe systems for which the rection rate was found to be completely solution-phase mass-transfer controlled. When the amount of material deposited was greater than 0.2 to 0.4 mg/cm2 there was an apparent enhancement in e which is attributed to the formation of a roughened deposit. This same phenomeon was obseived in the Cu/Zn Cu/Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass ,..~sfer controlled.

Jan 1, 1970

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

By Mitchell G, Clarke C

The high oas emissions which are associated with high production lonowall mining have provided a need to investigate the limitations and reouirements of the various gas control methods. The major relationships between oassiness and various other parameters are presented with computer analysis being adopted to assess the respective correlations. Some of the relationships are studied in detail with emphasis being placed on methods for overcomino the changes in conditions resulting from high production levels. The importance of the various drainage systems which can be adopted to combat high gassiness levels are analysed. Logical and necessary steps are also proposed for gassiness prediction and data monitoring as well as various combinations of gas drainage systems. The gassiness prediction methods which are discussed outline the need for a sound knowledge of the established worldwide methods together with a comprehensive study of the local mining and geological environment in order to develop a system which is adaptable to the changing conditions. This is particularly important in mines where high coal production levels are anticipated and the need for accurate gassiness relationships is essential.

Jan 1, 1988

The smelting operation associated with the production of aluminium has a voracious appetite for high grade carbon materials. Within the technical parameters of the Hall-Heroult process, the reduction of alumina to one tonne of aluminium results in the consumption of nearly 0.5 tonne of carbon at the anode of an electrolytic cell. This paper reviews the role of carbon and the basic quality requirements of carbon products in the production of aluminium, discusses the effects of certain physical and chemical specifications on smelting and related operations, and examines recent trends in the quality of these raw materials.

Jan 1, 1977

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

By Tonegato S, Wood M

The lack of objective data on roof bolting machines, bits, rods and overall system has created the need for an objective assessment of roof bolting. This work outlines a test rig for such objective assessment of component parts of the roof bolting system.

Jan 1, 1986

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

By Bearman R. A, Parkin R. M

Traditional quality control procedures for aggregates production within the quarry industry rely on off-line laboratory analysis, resulting in poor performance and inconsistent product quality. A high speed on-line aggregate classification system is described here. A product sampling system directs aggregate through an inspection chamber where a novel imaging system digitises the particle geometry. Data processing algorithms extract dimensional data and image features, while a neural network classifier assigns a qualitative shape descriptor to each rock particle. This system provides each sampled batch with a complete analysis of size and shape distributions, complementing a new generation of cone crusher technology to maximise product quality and plant efficiency.

Jan 1, 1995

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By Armstrong ME

The gas bubble energy generated by an explosive plays a major part. in the fragmentation, muckpile movement and damage produced. Previously, the interaction between gas pressure and the rock has been interpreted from a theoretical basis or a qualitative study of breakage mechanisms. A method to measure the fluctuations in gas pressure in rock adjacent to the blast has been developed. This peak pressure will vary with structure, as well as with distance and explosive type. The technique is simple to apply and can be used to observe the flow rate of gas at. varying distances. The apparent velocity of penetration is an indication of whether gas has travelled through pre-existing or blast induced cracks. The technique provides a ?n:eans of determining the suitability of an explosive for a given rock type, depending on the amount of displacement desired. The technique has application in optimir.irig throw blasting and predicting and controlling damage, particularly in highly structured rock masses.

Jan 1, 1986

By Martins V, Dunne R

A re-evaluation of the Hampton Boulder prospect in the early eighties resulted in a decision to proceed with mine development in December 1985. A 500 000 tpa gold treatment plant was commissioned in December 1986. The treatment facility was expanded to 1 600 000 tpa in July 1988. A tailings treatment plant to improve recoveries from harder gold bearing sulphide ores was built in December 1990. The development of an underground mine in 1991 meant that a source of sand for backfill was required. A sands plant to fulfil this requirement was commissioned during November 1991.As of June 1992 a total of 7 710 487 tonnes of ore have been treated through the New Celebration gold plant. Total gold production from inception of the new mine until June 1992 is 545 470 ounces obtained at an average recovery of 90.1 per cent from an average gold head grade of 2.4 g/t. The combined quoted ore reserves at the end of December 1991 was 14Mt grading 1.8 g/t gold

Jan 1, 1992

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

It is now 32 years since Walsh's classic publication (1) heralded the beginning of atomic absorption spectrophotometry (AA) as we know it today. During this time, AA has developed into the most widely used analytical techniques for the determination of the metallic elements. The years have seen progressive changes in instrumentation so that today it is a highly sophisticated technique. One area of development in AA that is experiencing renewed attention is in the area of electrothermal excitation. In this technique a flame is not used by the analyte solution is atomised by an electrically heated graphite furnace. For a large number of elements the graphite furnace atomic absorption spectrophotometer (GFAA) is considerably more sensitive than flame work. It is common to be able to detect concentrations one hundred times smaller than those possible by flame. Today's geochemists are finding that they can gain valuable information out of very low limits of detection. Electrothermal atomic absorption spectrophotometry (or GFAA) allows for low limits of detection and can be seen to be a valuable aid to geochemical prospecting Analysis.

Jan 1, 1987

By Y Gu

Based on the mode of occurrence, gold is classified into three categories: microscopic gold, submicroscopic gold and surface-bound gold. Microscopic gold, or visible gold, refers to gold minerals in which Au occurs in a substantial amount, such as native gold and electrum. Submicroscopic gold, ie invisible gold, refers to gold contained in the structure of other minerals (mainly sulfides) in minor to trace amounts. Surface gold is the gold that was adsorbed onto the surface of other minerals during mineralisation and subsequent oxidation or metallurgical processing. Gold mineralogy has a significant impact on its extractive metallurgy. Gold process mineralogy helps address problems related to gold ore processing. It is widely used as a predictive and troubleshooting tool in gold ore processing, and provides useful information on process selection, flow sheet development, recovery improvement and reagent consumption optimisation. This paper will begin with the classification of gold ores, and will focus on gold mineralogy and how it impacts extractive metallurgy through case studies.

Jan 1, 2008

Both safety and productivity in underground gassy coal mines can be improved substantially if an appropriate gas management system is introduced. A strong direct relationship exists between the gas emission rate, roof and floor strata relaxation zones characteristic, mining activities and gas drainage practices. Detailed knowledge of geological factors, gas and coal-rock properties, as well as mining systems are necessary for the methodology used in predicting overall underground gassiness, and planning gas capture and ventilation systems. Early gas emission calculations for various mining activities, particularly for the longwall mining system are essential. A reasonably accurate prediction of gas make as well as the design of ventilation, gas recovery (drainage holes) techniques can be made using 'Floorgas' and 'Roofgas' computer simulations, provided sufficient geological, mining, and gas data are made available.

Jan 1, 1998

By LaBrooy S. R, Ritchie I. M

Problems with the cyanidation of copper-gold ores Copper-rich gold ores are becoming increasingly important both within Australia and overseas (Dayton, 1982; Deng and Muir, 1994; Muir et al, 1993; Sceresini and Staunton, 1991; Solis, Hefter and May, 1995; Wall, Hornby and Sethi, 1987). In Australasia alone over 30 copper-gold deposits have been reported (Muir et al, 1993). Table 1 lists several of the deposits that have been processed. TABLE 1 Examples of copper-gold deposits in Australasia. Name

Jan 1, 1997