Search Documents

By R G. Reddy, Z Zhang

Viscosities of CaO-aluminosilicate ternary melts were estimated using a structure-based model. The model considers depolymerisation effects and related breakdown of the silicate network structure on the addition of metal oxides to the melts. The predicted values are in good agreement with the experimental values over the whole temperature and composition range.

Aug 21, 2024

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By A R. Cruden, M S. Egglseder

The formation of banded iron formation (BIF)-hosted high-grade iron ore deposits in the Hamersley Province, Australia has been debated for decades. Although a structural control on their formation is widely accepted, only the roles of large-scale structures (ie faults and folds) formed by brittle and ductile deformation have been considered to date. However, the deformation of multilayered sequences in the Hamersley Province (ie the Mount Bruce Supergroup), with their contrasting rheological behaviours, creates challenges for understanding the complex structural framework at regional to deposit scales, including the significance for mineralisation and orebody location.Our approach to understanding these complex relationships is based on an established principle of structural geology, which is to extrapolate microscale structures to deposit-scale structures and vice versa, supported by state-of-the-art 3D modelling techniques. Complexly deformed hand samples associated with the Mount Tom Price iron ore deposit (Hamersley Province, operated by Rio Tinto Ltd) have been analysed and visualised with 3D explicit (Move™, Midland Valley Ltd) and implicit modelling software packages (Leapfrog™, AranzGeo Ltd) and supported by microstructural investigations (optical and X-ray microscopy) and fieldwork.Our study shows that the deformation of BIFs in the central Hamersley Province is controlled by microscale chemical processes (ie dissolution precipitation creep) due to rheological differences between iron oxide and chert layers, contrasting fluid flow properties and layer thickness variations. These processes account for the removal of vast amounts of silica, its transportation by diffusion in the presence of a fluid and reprecipitation at low-pressure sites. Consequently, this structural framework was used by different upgrading fluids to form iron orebodies.CITATION:Egglseder, M S and Cruden, A R, 2015. Evolution of a structural framework for high-grade iron ore deposits, in Proceedings Iron Ore 2015, pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

By D Adhikary, M Khanal, B Poulsen, H Guo

During longwall mining, the ability to reliably estimate the height of longwall mining-induced fractures is critically important in order to effectively manage mining-induced water inflows and aquifer interference. The extent of mining-induced subsurface deformation, fracture, surface subsidence and aquifer interference is largely controlled by local lithological conditions, mining methods and mine layouts. Therefore for the purpose of quantifying mining impacts it is imperative to incorporate the local geology and mine plan parameters in a mine scale model. Two different numerical models based on 3D continuum (Finite Element Method) and 2D discrete (Discrete element method) domains, respectively, are developed to incorporate the mine site parameters of a study site in Australia. Both the models are calibrated and validated with measured mine data. The continuum numerical modelling method is used to investigate the change in permeability of the overburden strata due to underground extraction considering the full 3D nature of geology and mine layout. The discrete element modelling method is used to simulate the initiation and propagation of fractures, allowing the caving of overburden strata to be represented in a realistic manner, and the permeability enhancement of the strata overlying the goaf to be calculated from first principles. Permeability enhancement in the discrete element model is a direct function of the fractures induced in the deformation/caving process; fracture location, extent, aperture and connectedness. From the numerical modelling under the simulated condition for the mine studied here, it is predicted that the permeability of the caving zone from the goaf to five times the mining height increases by almost six orders of magnitude. In the fracture zone to approximately ten times the mining height, the change in permeability is predicted to be around two to three orders of magnitude. At the height of more than ten times the mining height the magnitude of permeability increased is predicted to be one to two orders of magnitude. CITATION:Khanal, M, Poulsen, B, Adhikary, D and Guo, H, 2018. Modelling of height of connective fractures during longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 254–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Myers

Since the mid-1990s, the Chino Mine Facility (Chino) located near Silver City, New Mexico has been developing a closure plan with financial assurance to protect water quality, as required by State regulations. In February 2002, Chino and the New Mexico Environment Department (NMED) reached agreement on a closure plan; a closure cost amount of approximately $US 394 million ($A 591 million) was finalised in April 2003. Both the New Mexico Water Quality Act Regulations (1977) and the New Mexico Mining Act Regulations (1993) guided development of the closure plan and financial assurance amount. The process incorporated many years of correspondence, studies, negotiations and administrative hearings. The major technical issues focused on regrading slopes of the leach ore stockpiles and waste rock piles; cover systems; water treatment systems; and abatement of ground water contamination. The proposed financial assurance amount covers all closure costs and provides for perpetual water treatment.

Jan 1, 2003

By M Mohammad Khani

An economic block cave is dependent to the characteristics of the rock mass at stages of caving. These are cave initiation, propagation and ore flow. In this research, the rock engineering system (RES), first established by Hudson (1992) to solve complex rock engineering problems, is introduced and verified against the well-established caving parameters established by Laubscher. There are two types of factors influencing caving and these are natural (cannot be controlled) and induced (operator controlled). A RES based interaction matrix is developed by determining the rating parameters required to reproduce the caving database using Laubscher’s caving parameters. This provides the relative importance of the parameters in the interaction matrix. After discussing the rock mass caving process and identifying all the effective parameters, an interaction matrix is introduced to study the cave initiation of rock masses. The expert-semi-quantitative (ESQ) coding method is utilised to assign the numerical value to each parameter’s interaction. Thereafter, the interaction intensity and dominance of each factor in the system is determined to classify these factors. Finally, all the parameters affecting caving operation and their weights on the RES system are identified. This new application of RES in block caving is very efficient and useful for any stage of caving studies and helps experts to make decisions more accurately.CITATION:Mohammad Khani, M, 2016. The application of rock engineering systems to block caving to identify the effective parameters, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 853–860 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

The region we call the West Coast is acknowledged as one of the richest and most diverse mineral provinces in the world. It's the most rugged part of Tasmania and our island is one of the most rugged parts of Australia, so that speaks for itself. A hostile land of razorback mountains, deep ravines, dangerous rivers, almost impenetrable rainforests and a climate that can change from mild to freezing in a matter of hours.

Jan 1, 1993

Hidden under picturesque Bemic Lake, in Canada's eastern Manitoba, lies a highly fractionated pegmatite orebody, hosting a unique assemblage of minerals. Accidentally discovered in 1929, the orebody had a brief history as a tin producer, but it is now mined by Tantalum Mining Corporation of Canada, Ltd. (TANCO), for its cesium, lithium, rubidium and tantalum bearing minerals. The mine also has potential for mbidium-feldspar, amblygonite, gallium rich mica, and quartz production. This paper describes the geology of the orebody, and its mining and processing. Selective, concurrent, mining and milling of the various products necessitates a high degree of planning and control, and these aspects are also discussed. The introduction of Quality Control and SPC are discussed, for such are the keys to excellence.

Jan 1, 1989

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

By C Mason, A Littleboy

This paper presents the results of a large scale survey of The Australasian Institute for Mining and Metallurgy (AusIMM) membership. This survey aimed to understand and define the key issues and drivers that AusIMM members perceived would shape the development of the Australian minerals industry over the next 20 - 30 years. Nine hundred and fifty-nine participants rated the importance of 11 issues and six drivers (generated from interviews with AusIMM members), and 236 of these participants also provided qualitative descriptions of the future. Issues were defined as problems or opportunities for the minerals industry that may be controlled or influenced by the industry, while drivers were defined as those factors that will influence the direction of the industry that are not within the control of the industry. The quantitative data revealed that the top four issues, in order of their perceived importance to the Australian minerals industry, were: investment in exploration, workforce, health and safety, and innovation. The top three drivers in order of their perceived importance, were: economics of mining, global context and Australian society. While the top four issues were largely consistent across professional groups examined, metallurgy and mineral processing professionals rated water inputs and energy inputs significantly higher than the other professional groups. For the list of drivers, there was strong agreement regarding their ranked order of importance across the professional groups examined. Within the qualitative data, however, a single issue (technology) and a single driver (economics of mining) dominated participantsÆ descriptions of the future. These findings provide important input into a broader program of scenario development for the Australian minerals industry being undertaken by CSIRO and its partners. The results of this study demonstrate the importance of using a mixed methodology in generating these inputs to understand more fully how important stakeholders view the future and the factors that will shape it. The results of this study are also discussed with respect to the role that CSIRO may play in facilitating the exploration of uncertainty around the future of the Australian minerals industry.

Jan 1, 2009

By P Breuer, D J. Robinson, A McFarlane, L L. Kuhar

Increasing global demand for commodity metals and capital and the greater operating costs of mining and metal production present significant challenges for the metals mining industry. Current conventional technologies may not be feasible for processing deposits of declining grade, challenging mineralogy or those that occur at increasingly greater depths. To overcome these issues, the development of a step-change technology such as in situ recovery (ISR), which reduces mining and avoids milling costs, may be vital in ensuring future economic metal production. ISR has been used extensively to treat porous soft rock deposits such as the water-soluble salts, sylvite and halite. Although ISR has typically been used for mining conventionally uneconomic uranium ores, it has also been used less frequently for the treatment of other restricted permeability hard rock deposits, such as those containing copper and gold. The reason for the limited uptake of the technology for hard rock mineralisations is primarily due to low natural rock porosity and permeability and hence poor response to available lixiviant. However, additional challenges include solution containment, management of groundwater and regulatory, ecological and societal requirements and expectations. CSIRO has focused on understanding the challenges of hard rock ISR and identifying global capabilities that can contribute to developing the essential enabling technical areas required to realise ISR. Specific focus areas include geochemistry and advanced resource characterisation; drilling and controlled rock-breaking technologies; solution chemistry and environmentally benign lixiviant systems; lixiviant delivery systems and ‘subsurface mixing’; subsurface hydrology and reactive transport mechanisms and models; downstream processing options; legal, social and environmental aspects; and techno-economic modelling. This paper will discuss ISR challenges including industry feedback focused on addressing this issue, gaps preventing ISR from being applied in practice, capabilities to overcome these gaps and the development of a collaborative approach to making hard rock ISR a reality.CITATION:Kuhar, L L, Breuer, P, Robinson, D J and McFarlane, A, 2015. Making hard rock in situ recovery a reality, in Proceedings Third International Future Mining Conference, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015