Search Documents

By D R. L Vedoy, L Botha, S P. Gumfekar, J B. P Soares

Most of the known in-place reserves of oil sands are found in Canada. These oil sands ores are mined using various processes to extract bitumen. The by-product slurry resulting from the extraction process, known as tailings, is discharged into tailings ponds. Fine kaolin clays are an important ingredient of the tailings because they remain suspended in water for many years. Current polymeric flocculation/dewatering technologies use acrylamide-based polymers such as polyacrylamide (PAM), but sediments produced using PAM-based flocculants hold considerable amounts of water due to the formation of loosely-packed flocs. Anionic polymers are better flocculants due to bridging and the charge-neutralisation mechanism. In this paper, we will compare the synthesis of two flocculants: thermosensitive, anionic flocculants and thermosensitive, hydrophobically modified anionic flocculants. The first flocculant is a copolymer of acrylic acid (AA) and N-isopropyl acrylamide (NIPAM), in which AA is the anionic monomer. The second flocculant is a copolymer of NIPAM, AA and the hydrophobic monomer N-tert-butyl acrylamide. We evaluated the dewatering efficiency of 2 wt per cent kaolin using both flocculants by comparing settling rates at different flocculant dosages, charge neutralisation ability and supernatant clarity. To better understand floc formation, we measured the floc size formed by both flocculants at different flocculant dosages. We propose that the hydrophobic monomer in the terpolymer flocculant helps expel water out of flocs, ultimately decreasing the water content in the sediments.CITATION:Gumfekar, S P, Vedoy, D R L, Botha, L and Soares, J B P, 2015. Thermosensitive, hydrophobically modified anionic flocculants for dewatering kaolin clays, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 45–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By M I. Pownceby, N Karimian, J R. Manuel, M J. Peterson

The CSIRO ore classification scheme for Pilbara ores was used as a reference frame to target recognisable ore types/textures with potentially elevated phosphorus content for detailed analysis. Particles of each individual ore texture were separated from a Brockman high-P ore and each class was characterised using methods including XRF, XRD, EPMA and synchrotron-based XAS. Results were then correlated with optical microscopy and hand specimen identification to establish any relevant associated mineralogical phases and/or textures. This represents a more systematic approach to identification of high-P ore components based on particle and goethite type and texture. The information can then provide the basis for more targeted P-removal strategies factoring in the relationship between particle/ore texture and phosphorus deportment

Sep 18, 2023

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By D R. Swinbourne, T Lehner

Study of the distribution of minor elements between copper matte andfayalite slag is important in determining appropriate methods tomaximise the recovery of valuable metals and the rejection of harmfulelements. Boliden Mineral AB operate a large copper smelter in northern Sweden, where they had noted that the loss of silver to the slag in the settling furnace appeared to be a direct function of the tin content of the slag. This work was aimed at determining whether or not this was a cause-and-effect relationship. Copper matte containing approximately 50 wt per cent copper and small amounts of silver and tin was equilibrated with silica-saturated fayalite slag at 1250¦C, then quenched. The matte and slag were then analysed for their silver and tin contents. It was found that there was no relationship between the silver distribution and the tin distribution. The silver matte/slag distribution ratio had a value of 120 ¦ 40 while that for tin was 2.8 ¦ 0.3. It is suggested that the most likely cause of the relationship observed at the Boliden smelter was matte entrainment in the slag.

Jan 1, 1999

By S Brochot

During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material coming from a selection of various drilling products or a sample coming from a mining test. This sample can represent several tonnes of material which are analysed and split to be used in various tests.In the current case, a composite sample is dedicated to semi-autogenous grinding (SAG) pilot plant tests. The property of interest is then the size distribution of the material. The sample is mixed and a subsample is taken to measure the size distribution which is considered as the feed size distribution. Then the remaining material of the sample is divided in several subsamples for batch grinding tests at different operating conditions. The product of each grinding test is then analysed to measure its size distribution.The grinding performances are analysed at the light of the measured size distributions for feed and product. But what is the accuracy of the measurement of these size distributions? What is the variability of the feed knowing each feed is just a subsample of the initial sample?The Pierre Gy theory of sampling answers these questions.The current paper presents, through a real example, the calculation of the measurement error of the size distributions and the variability of the feed between the different tests. The uncertainties of the grinding performances are then calculated and their impact on the results interpretation is then analysed.CITATION:Brochot, S, 2012. Sampling for grinding pilot plant test - the effect of size distribution variability, in Proceedings Sampling 2012 , pp 127-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

By S Prakash, M Danish, D Kumar

The green energy transition is speculated to cause an increase in the demand for raw materials while recycling rates are improving; discoveries are required to maintain supply. Geological remote sensing offers a cost-effective way of exploring mineral resources. While satellite and airborne imaging are routinely used for exploration targeting, a gap remains at the outcrop scale. Hyperspectral imaging (HSI) is advantageous for large-scale regional mapping, typically performed from satellite or airborne platforms. Accurately mapping geological lithologies remains challenging in inaccessible areas, such as rough terrain or mine sites. Proximal sensing techniques can boost geological activities’ reliability, safety, and efficiency in exploration or during mining activities. It also generates objective, reproducible results and valuable raw data that can be archived, further processed, and re-interpreted. Ground-based hyperspectral imaging of outcrops has steadily increased during the last decade due to sensor development and better processing routines. There is often a big technology gap related to mineral mapping, integration of images and spectra (reduction in manual identification of minerals and types) and hyperspectral data visualisation through remote sensing. TEXMiN Foundation, in collaboration with its industry partner Dassault Systemes Foundation, carried out the project, ‘Developing Hyperspectral Image Processing and Analysis, build a rich library of Hyperspectral images of a vast range of minerals from India which will help in increasing prediction accuracy of mineral deposit for mining exploration’.

Sep 1, 2024

By M Angus, S Konopa, A Virisheff, S Crispin

A positive mill reconciliation at a mine is a double-edged-sword. Much back slapping happens. The bank and the board can’t get enough until the downside becomes apparent. Over a prolonged period, there becomes an issue with market perception and the potential for shareholders to be misinformed regarding the potential value of the project. In addition, there are impacts on mine scheduling, waste allocation (or lack thereof), government expectations, and the potential for misguided external assumptions regarding the ‘unexpected’ results. The PT Agincourt Resources Martabe Gold Mine has shown a significant under-call, in the order of 20% total gold metal, between the Mineral Resource (MR) estimates and Grade Control (GC) estimates since production commenced in 2012. Recently, the under-call has been reduced by incorporating the use of grade control drilling in the MR grade estimates. Despite recent improvements in reconciliation, drilling in 2017 at both Purnama and Barani open pits shows that infill reverse circulation (RC) drill holes often produce significantly higher grades than those predicted in the MR block model. CITATION: Angus, M, Virisheff, A, Konopa, S and Crispin, S, 2018. Martabe Gold Mine, Indonesia: a positive solution for positive reconciliation, in Proceedings Complex Orebodies Conference 2018, pp 76–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

Simple parameters, capable of easy observation on-site under operating conditions without interruption to production, are outlined for the operational assessment of underground conveyor systems. Recording techniques, methods of analysis and deduction of operational characteristics are discussed for batch inputs to several points of a multiple belt conveyor system with limited inter-belt storage capacity. Particular attention is given to input and output load- time distributions, utilisation of inter-belt storage capability and system shutdown behaviour. Actual data, observed for a transfer feeder located between two trunk conveyor belts in an underground coal mine, is used to illustrate the operational assessment of an underground system. Load sensitive feedback systems-are briefly considered.

Jan 1, 1982

By R McIlwraith, B Breul

Two case studies are presented in this paper. The first one discusses a roller compacted concrete water supply dam that was constructed in El Mauro in Chile to provide water for agriculture activities downstream of a copper mine during the dry season. The 23 m high dam used a bituminous geomembrane (BGM) as the low permeability upstream facing element on the dam to control seepage through the dam. This is the first time that a BGM has been used in this application. A deep cut-off trench was used to control seepage beneath the dam and through the abutments. This paper briefly presents the design of the dam, including selection of the concrete mix and maximum aggregate size that the use of the Coletanche BGM allowed, and provides details of the construction, quality control and assurance of the installation of the BGM. An ultrasonic apparatus was used as part of the quality control on the BGM seams.The second case study discusses a tailings dam in Cerro Lindo, Peru (near Chincha), where a watertight BGM was installed on the upstream face. Results are presented of the survey done by a consultant on the behaviour of the dam and in particular of the BGM following an earthquake of magnitude 8.1 in Chincha close to the site. These findings on-site were checked by trials in a laboratory in California. Test results are given and explained.CITATION:Breul, B and McIlwraith, R, 2015. Case histories – roller compacted concrete dam waterproofing with a bituminous geomembrane in Chile and a tailings dam in Peru subject to an earthquake of 8.1 magnitude, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Yamatomi, Y Tamanishi, S Miwa

The four-dimensional (4D) network relaxation method, originally developed by Akaike in 1999, uses Lagrange relaxation and is known for its ability to include the price change and possible better outputs, but the computation time is huge. However, the continuous advancement in computer technologies allows the use of higher-speed computers with more memory capacity. Therefore, in this paper the authors have tried to implement the method with adjustments and improvements in its algorithm to suit the current computing system. As a result, the computation time has been drastically reduced and more constraints can be included, which makes the scheduling a more realistic one. The case study of an open pit gold mine with 129 500 blocks can be solved considering the capacity constraints in 71 seconds. In previous case studies, the mined ore had to be processed or disposed of immediately. Now, stockpiling can be included as another option. Since the details of the algorithm are still being improved, the computation time is a little longer than the previous cases without the stockpiling option. However, it is found that scheduling with the stockpiling option is possible in a reasonable time. In conclusion, the 4D network relaxation method has become more useful with advances in computer technologies and provides better results.

Sep 26, 2011