Search Documents

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By Pinczewski WV, Nowak LP, Tanzil WBU, Jenkins DR, McCarthy MJ

An experimental and theoretical study has been made of the drainage behaviour of two-dimensional packed beds drained from an outlet in the sidewall of the bed in order to identify the fundamental me- chanisms involved. Under these conditions a grad- ient develops in the air-liquid interface in the direction of flow with the interface tilting towards the outlet. This results in a significant volume of liquid being retained in the packing on completion of draining when the interface first reaches the bed outlet. Residual liquid volume and the shape of the air-liquid interface as a function of time were det- ermined experimentally in a two-dimensional packed bed where the packing consisted of glass spheres ranging in size from 0.6 to 10 mm dia. and the bed was drained at superficial liquid velocities rang- ing from 0.007 to 0.32cm/s. The test liquids used were water, glycerine/water solutions and kerosene resulting in a viscosity range of 1 to 10 mPa.s and a surface tension range of 0.0243 to 0.072 N/m. Assuming laminar flow within the bed, a compu- tational model was developed to predict both the liquid residual ratio and the temporal evolution of the drainage profile within the bed. The computed results were in good agreement with the experimental data over the entire range of conditions invest- igated. the computational model was used to estimate the relative importance of the effects of changes in hearth conditions on residual slag volume for typ- ical blast furnace operating conditions. On the basis of the computed results it is concluded that coke quality is a major parameter affecting hearth drainage performance.

Jan 1, 1981

The safety culture in mining has progressed towards a zero tolerance of injury. This change has required that some historically inherent risks of mining are engineered out or reduced. One of the significant causes of fatality in Western Australia and Worldwide mining is through rock fall, subsidence and inrush. Efforts put into understanding the material properties of the ground we mine and the backfill we place are reflected in improved safety statistics. It is no longer acceptable to not manage these risks and mining, to be sustainable, has to be safe.   Mining historically produced waste products with little consideration of recycling or impact on the surrounding land. The rehabilitation of mining waste products such as mill tailings, heap leach and waste rock is one step towards managing the environmental impact of these waste products. A better step is towards recycling and redepositing these products to produce a more environmentally sustainable mine site.   Gold fields St Ives lease is an active network of new and historic undergrounds and open pits within the Lake Lefroy and Kambalda district. The process of creating voids underground followed by open pits mining through the old voids allows the use of backfilling to control inherent hazards and dilution. Backfill provides opportunity for the disposal and recycling of mining waste materials at the same time as meeting requirements of mine support. Materials available on the St Ives site include spent heap leach, reclaimed tailings and waste mullock. Through recycling and re-depositing these materials to St Ives and neighbouring mines, the reliance on imported material to meet their needs and impact on surrounding land is reduced.   At St Ives, paste fill and barricade design have been reworked to allow backfilling into stopes with water inflows up to six litres per second. This has required a rethink of the drainage and monitoring of water management systems previously used for hydraulic fill and apply them to paste.   The St Ives open pits have developed methods to mine through underground workings and individual stope voids up to 62,000m3. Here backfill is used to reduce the consequence of catastrophic, unexpected failure of the crown and minimise ore lost down voids and dilution through increased blast movement. This paper outlines the less common methods being adopted to use the recycled materials and ways it has been managed to suit the needs of the company.

Jun 1, 2010

The application of modern sciences prior to nineteenseventies have resulted in the placing of Continental Drift theory into broader concept of Plate Tectonics. The concept is applied to explain the Cenozoic Tectonics of North Sumatera.Oceanic crust flooring the Indian Ocean is moving northeasterly and being obliquely subducted at a Benioff zone along the western margin of Asian Plate, marked by the Sunda Trench in the west coast of Sumatera. This phenomenon was generated since late Mesozoic, continued during Cenozoic era up to present day, resulted an exellent example of arc-trench system which can be traced along SW - NE transect of North Sumatera.The oblique-subducting plate of Indian Ocean beneath Asian Plate, together with spreading of Andaman seafloor beginning in Pliocen epoch, have led to the origin of Sumateran Fault System; the System extends throughout the length of Sumatera island. In the region under review it comprises almost contiguous set of broadly SE-trending. Evidences for transcurent-dextral displacement have been observed.

Jan 1, 1990

Oxygen is required for the leaching of gold ores in cyanide solutions. The source of this oxygen demand and the effect of dissolved oxygen concentration on the rate of the process are briefly reviewed.A method of measuring the oxygen consumption rate is described and some experimental results reported.Fundamental aeration theory and rating of aerators is summarised to show how this type of experimental work provides the basis for full-scale design of aeration equipment.

Jan 1, 1984

By Neto J. A N

Usually there are organisational interfaces between each stage - companies or departments. Each organisation will have different ideas about "optimum" operation. These ideas will be driven by how the performance of each is measured ' and rewarded. Therefore it is important to set up data acquisition processes with respect to maximisation of overall profitability and resource utilisation. In the simplest case - if the miners are paid on tonnes and the concentrator has severe grade penalties on concentrates, then there is the possibility of a conflict of interest over metal Balance.

Jan 1, 1991

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

The silver-lead ores of Yerranderie occur in a series of narrow, flat-dipping lodes in small bodies of quartz porphyry, intrusive into Upper Devonian volcanics, which are exposed in the western flank of the Permo-Triassic Basin of central New South Wales, about 80 miles south-west of Sydney (Harper, 1930; Lawrence, 1953). The lodes strike about E.-W. and are from 1,200ft. to 2,000ft. long. They consist of a series of ore shoots from 3ft. to 100ft. long, and up to 5ft. thick, though commonly under 2ft. thick, interspaced with low grade sections. They dip at from 18°S. to 400 S., and have persisted down the dip for 1,450ft. (693ft. vertical depth) in the Wollondilly mine, for 1,120ft. in the Bartlett's mine, and for 850ft. in the Wonga mine.The grade of ore in the Bartlett's mine was from 32% to 40% lead, from 100 oz. to 130 oz. silver per ton, 0.5 to 4.0% arsenic, with ore ,as rich as 20% arsenic on the No. 6 and No. 7 levels of the Silver Peak mine, the underlay extension of the Bartlett's lode, about 1% copper, and up to 4 dwt. gold per ton. In the Wollondilly mine the average grade was 15% lead, with sections as rich" as 36% lead, from 75 to 165 oz. silver per ton, 0.6 to 3.3% arsenic, 0.2 to 0.7% antimony, 0.8% copper, and up to 7...5. Cl~t. gold per ton. The zinc content of the ores is slight, and has not been recorded.Mining began about 1898, and to date more than 110,000 tons of ore, valued at £1,800,000, has been raised. Large scale mining ceased about 1935. The chief mines operating were the Bartlett's mine (formerly Colon Peak), the Silver Peaks, which is the underlay extension of the Bartlett's, the Wollondilly (or Yerranderie) mine, and the Wonga' (or Tonalli) mine.

Jan 1, 1953

The paper presents an overview of the mining industry of Papua New Guinea. Although the Bougainville problem is still unresolved, new mines like Ok Tedi, Misima and Porgera, which have come on stream during recent past, have raised hopes of sustained growth period in the industry. Kutubu Oilfield is also being developed in the Southern Highlands and the oil production has commenced from July 1992. Government revenue from these mega projects will increase five-fold during 1993 and 1994. A new mine which is being planned is the fabulous Lihir Deposit, on an island renowned to be full of gold. Gold occurs within a volcano which still contains high temperature ground water because the system which created the deposit is still geothermally active.In Papua New Guinea, problems of environmental management are far easier to tackle than those of a socio-political and economic nature involving compensation payments to the landowners and the distribution of royalties and taxes between the national and provincial governments. At the socio-political level, the country has not been able to resolve the problems of land rights versus mining rights. Whenever mining starts in a big way, it raises people's expectations to a very high level, which then becomes the focal point of dispute between landowners, provincial governments, national government and mining companies. A new system called 'Forum' has been tried to bring all parties together and son out the issues. The system appears to be working well in new mines like Ok Icdi, Porgera, Misima and Kutubu Oilfields.

Jan 1, 1993

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

A pilot plant has been constructed for the low temperature carboni-zation of Wallarah (N,S,W6) coal at the rate of 300 pounds per hour. The plant was built and tested at Australian Mineral Development Laboratories for Broken Hill Pty, Ltd. Char product was required within the specifi-cation 15.5 `S' 1 per cent volatile matter. The design was based c atz an entrained state carbonizer developed by Parry and U.S. Bureau of Mines co-workers at Denver, U.S.A. The method involved the carbonizatioan of fine coal by entrainment with air in an externally heated reactor.. The heat required for carbonization of tits coal was supplied to the be, both through the reactor walls and also by internal cambustion of products .

Jan 1, 1963

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007

Mineral exploration is the business of finding and defining ore deposits. Ore bodies are developed into mines and mines supply every mineral and metal upon which our society is built. Whether it be steel for our bridges, cement and aggregate for our concrete, coal for our power stations, copper for our wire, phosphate for our fertiliser or gold for our jewellery it first must he found, then mined and processed before we can use it. There is no other way.

Jan 1, 1993

By T Leach, F Kaiqiang

The Jianchaling gold deposit is located about 1200 km south west of Beijing in central China. The deposit was discovered in 1988 by the Northwestern Geological Exploration Bureau (711 Exploration Team). Sino Gold Limited, an Australian based company, developed the mine in 1998 and is currently operating a 1000 t per day underground mine, producing about 80 000 ounces of gold per year. The pre-mine resource for Jianchaling was 1.6 million tonnes at 9.85 g/t gold. The deposit occurs within the east-west trending Mesozoic Qinling-Dabie orogenic belt formed during the Yanshanian Orogeny. In the Jianchaling region, gold mineralisation is primarily hosted by regional west-northwest to east-southeast striking faults, the most important of which, the reverse sinistral F145 fault, hosts the larger gold deposits including Jianchaling. At the mine scale, the most important zone of mineralisation is localised within a shallowly north dipping dilation on the F145 fault. Proterozoic dolomite forms the hangingwall and serpentinite and talc schist the footwall to the fault. Within the footwall, serpentinite is the most important host rock to mineralisation. Initial alteration involves replacement of serpentine to dolomite ¦ pyrite, talc to ankerite ¦ pyrite, and magnetite and chromite to pyrite, the latter locally through a transitional hematite phase. Proximal to feeder structures, the carbonate minerals have undergone partial dissolution and replacement to quartz. Gold is related to arsenean pyrite and marcasite rimming and replacement of early-formed pyrite, and associated with iron release during the processes of dolomitisation, silicification and carbonate dissolution.

Jan 1, 2004

A new test coke oven of seven cubic foot capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from the flues on either side of the charge. The method of charging permits close control of charge conditions'such as bulk density and moisture content. These conditions, as well as coking conditions (e.g. flue temper- atures., coking time) must be varied to simulate conditions in different batteries, The effects of several variables on coke quality are discussed. Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes; for 17 tests, the average A.S.T.M. stability and hardness indices for the test oven coke were 38,5% and 69.7%, while those for the battery coke were 37.1.% and 67.6%.

Jan 1, 1969

By J Ranford, A Harris, K Laughton

The Angas Zinc Mine (Angas) is a poly-metallic, underground mine in the Adelaide Hills that has been developed through arguably one of the most volatile financial time periods in living memory. From boom times during the commencement of the project, the global financial crisis (GFC) through the stabilisation of the operating period and then a subdued capital market for the period where mine life extension was targeted, the financial environment has always presented a different set of challenges. Indeed even the Underground Operators’ Conferences that have been held across the span of the project allude to these changes: ‘Boom and Beyond’, Launceston (2008); ‘Safe, Innovative and Sustainable’, Canberra (2011) and ‘Managing the Margin’ in Adelaide (2014).Angas gives a rare opportunity to see the entire life-of-mine of a project and its economic performance within a relatively short time frame. Angas, owned and operated by Terramin Australia Ltd (Terramin), will have undergone resource estimation drill out, feasibility study, permitting, commissioning, operating and completion and rehabilitation all within a period of approximately ten years. A number of sensitivities of the project were tested, particularly in the bankable feasibility study (BFS) stage and the aim of this paper is to identify the factors that impacted the operations profitability the most, whether they were identified preproduction or not. The key sensitivities assessed in the BFS were typical of similar studies, including operating costs, metal recoveries, capital costs, zinc prices, lead prices and exchange rates. The manner in which these sensitivities presented themselves in real life were not as anticipated and modelled in the feasibility study and were also heavily impacted by technical challenges.CITATION:Harris, A, Laughton, K and Ranford, J, 2014. Feasibility to mine completion – the real impacts on project economics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 99–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

The C.S.A. copper lead zinc mine, located seven miles north of Cobar in Central Western New South Wales, is the largest known mineral occurrence in the Cobar Mining Field. Hosted by the steeply west dipping, west facing sediments of the Cobar Group, the generally discordant orebodies occur within a strike width of 600 ft and an overall strike length of 1200 ft. They comprise lenticular steeply north pitching and east dipping zones of sulphide mineralisation which range in composition from massive pyrite-sphalerite-pyrrhotite--galena to less massive pyrite- pyrrhotite-chalcopyrite varieties. The thinly bedded siltstones, shales and graywackes hosting the mineralisation appear to have derived many of their constituents from volcanic sourcesä They have been metamorphosed to the greenschist facies of regional metamorphism. At least two stages of deformation and folding have occurred. The first stage folded the rocks on a south pitching fold axis into their present configuration, and super- imposed a strong axial plane cleavage which subsequently guided the emplacement of the mineralisation. The second stage of deformation is considered to have controlled the zonal distrib- ution of the orebodies and the appropriate fold axis appears to coincide with the long axis of the orebodies.

Jan 1, 1969

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989