Search Documents

The Bendigo goldfield is centred on the urban area of Bendigo (population approximately 60 000) in central Victoria, 130 km north west of Melbourne, Australia. Gold was discovered at Bendigo in 1851 and production continued through to 1954. The Bendigo goldfield is the second largest goldfield in total gold produced in Australia, after KalgoorlieÆs Golden Mile with a total production of 22 million oz. The geology of the Bendigo Field consists of a series of tightly folded, interbedded sandstone and shale sediments. Within the sediments the gold mineralisation is hosted in quartz reefs or ribbons closely associated with anticline axes and reverse faulting. The gold within the quartz reefs is typically both coarse grained and erratically distributed.

Jan 1, 2002

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By Hoskings AD

Bolting forms a prestressed elastic layer of rock which is capable of supporting loads at right angles to the bolted surface. Investigations on rock bolting made with a number of different models give rise to empirical and theoretical prin- ciples for the formation and action of the layer. In the models, flat and arched layers of many materials were used simulating rock conditions ranging from closely interlocked blocks to fragments of various shapes. Results of observations made in the underground works of the Snowy Mountains Scheme are related to the mode of action of bolted surface layers of rock. There is abundant experimental, theoretical and practical explanation for the well-demonstrated capability of bolting as a means of rock support.

Jan 1, 1971

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

By P Rubie, J Russell

This paper looks at the past, present and not too distant future of grinding mill relining.Since the adoption of autogenous grinding (AG) mills and semi-autogenous grinding (SAG) mills as the primary ore reducing devices in the comminution circuit, plant shutdown frequency and duration has largely been driven by the liner maintenance requirements of these mills.The past 30 years have seen the introduction of many technologies to reduce relining times and frequencies. Advanced relining systems have been developed which include single and twin Mill Relining Machines, capable of placing large (up to 8000 kg) liners, high energy recoilless THUNDERBOLT Hammers, and high capacity Feed Chute Transporters. Despite these advances, today many of the hazards associated with mill relining remain and reline times still vary considerably between mine sites. A sophisticated discrete event simulation program, designed to analyse the mill relining process, has revealed the dominant influences on reline times of crew performance and of the need for safe access to larger segments of the mill.A new generation of advanced and semi-automated technologies is currently being tested that will address these remaining challenges. These technologies remove people from the hazardous environment inside the mill and will allow techniques used in modern advanced manufacturing to provide a near-future step change in mill relining safety and performance.CITATION:Rubie, P and Russell, J, 2018. 21st century relining – the path to greater mine site profitability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 621–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

There is a difference in design aspects between steel linings and rubber linings for grinding mills. The basic design rules for rub- ber are described as well as the liner designs for different applications.

Jan 1, 1978

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

Brief summary of results obtained by a French-Japanese cooperative study on the bottom of trenches around Japan. The geophysical prospection, multi beam echo sounding and direct observation with submersible dives of the trench bottom clarified the details of the subduction of oceanic plates. It may be noted, among many new facts found: 1. The subduction and geologic structure resulted from the process is different according to the nature of subducting oceanic plate, and the geology of the land behind the trench. Thus the Nankai trough characterized by the developpement of accretionary prisms is contrasted to that of the Japan Trench where the basement rocks are exposed on the land side cliff of the trench wall. 2. The compressional tectonic situation prevailing in the trench bottom provokes the venting, along the fissures on the bottom, of water contained in sediments. Hydrocarbons contained in the sediments are comming out with water and give nutrients for bacteria. Clams, tube warms, sea slugs and shrimps are taking these bacteria as their food and biological communities with exceptionally dense population for the deep sea of more than 3000 meters in depth are formed on the field of accretionary prism and wall of the land side cliff. 3. An intense compressional tectonic field resulted from the subduction is inducing the transition from the subduction of oceanic plate to the collision of a part of the plate to the continental plate.

Jan 1, 1987

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

By Nowell SB, Cottrill DA

Host-rock - wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

With the recent wider introduction of friction hoists of the Koepe type. for winding from depths of more than 3000 feet it has been found that failure by fatigue is the most common form of rope deterioration. Large numbers of wire breaks occur near the centre of the rope cross-section and it is difficult to detect these with certainty using the preferred d.c. magnetic test. For best results with conventional search coils their dimen- sions should be related to the typical wire break field pattern surrounding the longitudionally magnetised rope. The field of a broken wire was experimentally determined, using a Polish type MD6 Defectograph wire rope testing magnet and a short prepared length of rope with a movable simulated broken wire. The external field distortion perpendicular to the rope was measured by means of a gaussmeter and Hall probe. The advantages of this method are that terrestial magnetism and inherent rope "noise" have no effect on the results.

Jan 1, 1971

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By S Shipard

Filters are used in water treatment and hydrometallurgical process plants for objectives such as generating a dry spadable solid, pumpable high density slurry or high purity filtrate. The priority objective of every polishing filter, sometimes also termed clarifying filters is high purity filtrate and these are found in many diverse industries and even different applications within the same industry.To generate a high purity filtrate, process designers have the choice of many different polishing filter products, but in reality very few polishing filters are based on fundamentally different filtering concepts.This paper reviews the technology merits of well-known and the more recently developed polishing filter products and aims to assist metallurgists and engineers with the selection of an appropriate polishing filtration technology for pregnant liquor filtration and other process applications, plus a guide to best practice.CITATION:Shipard, S, 2013. Polishing filters for mineral processing plants, in Proceedings MetPlant 2013 , pp 118-125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By Morinaga K

The optical basicity (A, Pb2+ as probe ion) of various oxide glass systems has been measured to establish the new basicity scale of slag melts. Best conditions of glassy fragments to measure A were as follow, (1) 1 ti 4 x 10-2 wt% Pb content, (2) 0.2 mm in thickness, (ii) enough annealing (about 10 hr) at a temperature 200¦C below Tg., and (4) polishing a surface well. the variation of A with composition was correlated to that of relative oxygen activity of slag melts. The estimation of basicity of slag melts from it could be valid. The A of opaque and coloured quenched slags could not be measured. An approximately linear relationship, however, exsisted between the isomer shifts (b) of Fe3+ ion in slag derived from the Mossbauer effect and A. Therefore, -4 of various metallurgical slag could be estimated from this relationship. These results can be expected to establish the new basicity scale of slag melts as the Louis basicity.

Jan 1, 1980

A mining joint venture presents a real management challenge to achieve harmony with the other participants in the successful development and operation of a mine. This can best be facilitated by a detailed agreement and guided by a set of joint venture principles which recognise the differences of the interests of the parties and seek to establish sound business and personal principles by which differences not anticipated in the agreement might be resolved. The major and minor co-venturers can and do present potential difficulties to one another. This paper, one of the pair in the joint venture panel discussion session, predominately presents the minor's viewpoint. Usually commercial matters such as project finance, areas of interest, divestment, pre-emptive rights and decision-making can be adequately covered in the agreement. However, when the parties disagree and have difficulty in resolving their differences, the joint venture principles should be used to advantage to resolve relationship difficulties.

Jan 1, 1997