Search Documents

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022

By Watt JS

The ash content of coal can be determined using radioisotope X-ray techniques. A number of overseas applications of X-ray techniques are described; however these suffer from the disadvantage of either not compensating for iron variations or, if compensation is used, using X-rays of low penetration with consequent sampling difficulties. Current Australian Atomic Energy Commiss- ion (AAEC) research on X-ray techniques is aimed at overcoming the limitations of these methods. The AAEC method involves making measurements proportional to mass absorption coefficients of X-rays in coal at two energies. Calculations and experiments with X-rays up to 35 keV have shown that ash content can be determined to about 1 wt.%. This work is being extended to higher X-ray energies to enable the technique to be used directly on a conveyor belt or in a hopper. Neutron techniques can be used to measure the concentration of specific elements such as carbon, hydrogen and silicon in coal. Their con- centration is correlated to the coal parameters of interest. Methods of moisture determination based on hydrogen measurement and ash determina- tion based on silicon and aluminium measurement are described. Energy content can be determined accurate- ly by analysing the carbon content of coal

Jan 1, 1978

By R Barrette, V Lawson

Over the last year at Clarabelle Mill, three circuit reconfigurations were implemented. One circuit reconfiguration, æA CleaningÆ, was initiated due to a furnace failure at the smelter complex, and two of the circuit reconfigurations, æincreased copper (Cu) separationÆ and the æInterim IsaMillÖ circuitÆ, were seen as opportunities to increase cash flow through the mill. A Cleaning and the Interim IsaMillÖ circuit took advantage of engineering design already completed for a major capital project. The engineering for each was modified, as needed, and construction of the required portions of the capital project was fast tracked. The increased Cu separation circuit change used existing test and plant equipment to increase the plant Cu concentrate production. Implementation of the projects required teams that included operations, maintenance, technical support, project management and capital project resources. This paper discusses the business reasons driving the changes and the forethought or synergies with other work, which made them a success, and what was learned through each project. CITATION:Taylor, A, Lawson, V and Barrette, R, 2012. Responding to the challenge - Necessity driving circuit change, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 247-254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

By Moeller T

The Bottle Creek mine, when opened next month, will consist of three open cuts, Emu, VB and Boags, feeding ore to a central mill. The open cuts cover a strike length of 4.5 kilometres which forms part of a linear structure, which can be traced geochemically for 26.0 kilometres. With the exception of a few small gossanous outcrops at Emu, the deposits are completely covered with insitu laterite and alluvial overburden. Since its discovery in 1984, the deposit has been subjected to three major reverse circulation (RC) drilling programmes which have successively closed up the drill spacing on the main mineralized zone to 25m horizontally and less than 25m vertically. All resource calculations have been based primarily on samples of RC drill cuttings from these programmes. Ore reserve calculations have been completed after each drilling phase. They began with a simple polygonal technique, progressed through two sectional half-distance calculations and are now being completed with a 3-D geostatistical technique. Because of the style of mineralization, Norgold personnel paid particular attention to assessing the variability of the mineralization by using repeat samples, repeat analysis and diamond drill vs RC comparisons. In addition, close attention has been paid to obtaining an accurate estimate of the global SG of the ore bodies. Particular care has been taken to obtain complete drill intersections of the orebody and to maximize wet sample recoveries. Extensive re-sampling and re-analysis of samples has confirmed that Bottle Creek is unusual for an oxidized gold deposit in that all the gold appears to be very fine grained, and evenly distributed within the mineralized zone.

Jan 1, 1987

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

By G M. Taylor

The application of high technology to monitor and control fire life safety, critical functionality in tunnels and underground spaces generally has progressed at an ever accelerating rate over the past decade. Today these systems comprise some of the most complex and little understood aspects of the tunnel/underground facility construction industry, with this area being perceived as high risk comprising impenetrably complex ‘black box’ technology covered in blinking LEDs. This paper will seek to explode some urban myths and common misconceptions associated with such systems, providing its intended audience with a review of what all this technology comprises and where the real risks lie in its delivery lie.The author contends (and looks to support such contention via this paper) that by applying baseline project and risk management processes to the procurement of this widely misunderstood black box technology, the quality of the final outcome can be much improved, driving innovation, reducing both cost and significantly mitigating delivery risk.CITATION:Taylor, G M, 2014. Procuring control and intelligent traffic systems for major new build projects – avoiding pitfalls and maximising value, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Jundee gold mining operation is located in the Western Australian Yandal Greenstone belt. Jundee is a mature operation encompassing multiple and complex underground ore resources, dwindling open pit reserves, large surface stockpiles, small satellite resources and two near-mine but stand alone process plants. The imminent completion of continuous open pit mining and the associated drop-off in total mill feed precipitated a review of the strategic mine plan and development of options that would optimise the exploitation of the remaining mineral resources and the utilisation of the existing plant and infrastructure.An initial review of the strategic decisions to be made, available options as well as the quantity, complexity and co-dependency of the strategic variables quickly led to the conclusion that an Operations Research style modelling approach would be appropriate. An 'off-the-shelf' program engine by the name of WHATSBEST! (LINDO Systems Inc.) was chosen on the basis of price, reputation and ease of use. The model was formulated with the unknown variables (being the ore mining rates) expressed as a proportion of the maximum achievable ore mining rate from each source. Costs were defined as variable or fixed, with this definition being a key aspect of the modelling process. The critical application of the model was in determining the optimal extraction rate of ore, the destination (ie Jundee or Nimary mill) and the sequence of extraction of each ore source that maximized the cash flow of the operation. The program was designed to be able to quickly derive an optimal result from the many variables, replacing the previous laborious iterative process of arriving at an acceptable answer by means of several large and static spreadsheet models. This paper presents the process of selection, formulation, application and scope of operation of the turn-key linear and non-linear program strategic model now used as part of the Jundee Operation strategic decision making process.

Jan 1, 2002

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By Blackwood R. L, Crichton G. P

In recent years, the value to Australia of the introduction of a system of resource rent taxation on the mining industry has been frequently debated. The forms that this rate of return based tax could take, and the impli- cations on government revenue and mining com- pany profitability have been discussed at some length. Further, the selective application of this taxation scheme to certain mining industry sectors has received considerable attention. This study takes the form of a survey of the taxation history of one significant Australian mining venture, the Mount Lyell Mining and Railway Company. The conditions faced by this company during its history are used as a base for the imposition of rent taxation schemes. Comparisons are drawn between the historical taxation liability of the company and that which would have been incurred if a resource rent form of taxation had been in existence. From the results of the study, it can be concluded that while the company can be con- sidered to have been a successful enterprise during most of its history, it has not achieved a level of profitability which would warrant the collection of any form of excess profits Tax.

Jan 1, 1979

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By A Weeks an, R Bertinshaw, S Khosrowshahi

Good mining is central to any approach to value tracking. Good mining occurs where the ore is correctly delineated, measured and fed to the mill. This process is usually referred to as grade control, ore control or quality control. There are now ways to measure the efficiency of this process, such as by using conditional simulation, and a brief synopsis is presented. Resource estimation is the foundation of ore reserve estimation, which should enable useful prediction of the expected metal to be recovered from mining and milling. Significant improvements have resulted from applying new techniques such as the Chain of Mining (CoM) method, which models the mining process. Again, a brief synopsis is presented. Tracking value from the mine through the mill implies a linear sequence of processes that can be modelled. Reality is more complex and there are error components, feedback loops and breaks in the Chain of Value. Modelling the total production process in a number of operations is considered, including the various impacts on producing reconciliations. Procedures are also discussed for handling a number of difficult issues such as: different data supports, stockpiling strategies, blending from multiple ore sources, blast movement and underground ore extraction.

Jan 1, 2002

The importance of proper planning, preparation, and execution of a steady state sampling campaign for metallurgical plant assessment must not be underestimated. Careful planning can increase the amount and reliability of information from an optimum number of samples and fully utilize available plant data. It requires specification of the data required, determination of run duration sampling frequency, the selection, modification and testing of sample points and cutters, as well as organisation and briefing of plant and sampling personnel. Preparation immediately prior to sampling, the conduct of the sampling campaign itself and procedures to handle the collected samples and information are discussed. Cutter design, fabrication and use are described in detail, and typical sampling situations, for ball mills, classifiers, pipes, launders, flotation cells and thickeners are considered individually. Measurement of pulp flow rate can often resolve difficult mass balance problems, and discussion of convenient techniques is included.

Jan 1, 1976