Search Documents

By C te Kloot, Z Liu

Blast performance and the resulting drawpoint condition and volume of oversize has the potential to impact operator safety and mine productivity. Underground measurements showed that approximately 14 per cent of production rings in the Ernest Henry Mine (EHM) sublevel caving (SLC) operation had either overbreak in the brow or left collars. There were also oversize rocks reporting to approximately 30 per cent of drawpoints, which accounted for over 7 per cent of total production and significantly impacted production rates. A series of trials were conducted in 2015–2016 at EHM to test changes to certain charge parameters in an attempt to optimise blasting results and, in particular, reduce oversize and overbreak. The detailed analysis conducted included field observations, hole surveying, blast monitor analysis and blast modelling. There were a total of nine charge parameters tested in the project, which fell into two major categories: energy distribution and inter-hole delay. These were based on observations made in establishing baseline data and those parameters most likely to have a significant impact on overbreak and oversize.Key results from the project included oversize reduction and improved brow conditions when energy distribution was reduced through changing charge lengths in certain holes in the standard charge plan. Similar benefits were also seen when the inter-hole delay between blastholes was reduced from 50 ms to 25 ms. Based on these results both changes were made to the standard production ring charge plan at EHM.Moving forward, the aim is to continue monitoring the results from the changes made on all levels to ensure efficiencies are being realised and sustained. A 3 per cent improvement in oversize as a percentage of total tonnes and improved brow conditions not only has a positive impact on production rates, but removes people from any potentially hazardous situations and contributes to a safer working environment.CITATION:te Kloot, C and Liu, Z, 2017. The evolution of production blasts at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 33–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By P Wopereis

The Nokomai valley is located within the pumpellyite/actinolite facies of the Otago Schist, a regional scale metamorphic belt in Southern New Zealand. The Otago Schist is dominated by psammitic and pelitic greyschist with more subordinate greenschist, quartzite, marble, and ultramafics. Mining in the Nokomai, began in the 1860s, with sluicing of terrace gravels in the lower valley. Good gold is reported to have been won from unconformities within very weathered gravels lower in the terrace sequences, and particularly from within channels which dissect these older deposits. Gold was recovered from these terraces in the main Nokomai Valley, and two major tributaries (Victoria Gully and Bullock Head Creek). In the period 1885 - 1887 further gold was discovered in basal gravels beneath the Nokomai flats when the Hunter brothers sank two shafts and excavated a connecting drive to discover a lead 1.2 - 1.5 m thick. The Golden Lion Sluicing Company began mining in 1896 using an hydraulic elevator on the very 'tight' 1.8 - 2.4 m of basal gravels. This operation was followed by the Nokomai Gold Sluicing Company whose average return grade was >485 mglm3 until mining ceased in 1943 (Wopereis; 1988, 1989). A quartz vein, Commissioners Reef, was worked for small production at some time during the 1920 - 1930 period, until fault termination of the vein ceased production.

Jan 1, 1996

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By C Staak, H Mischo, A Fichtner, F Reuter

In mining and remote areas of resource industry, there has been a development towards lacking emergency medical first aid response, that creates a potential disadvantage for patients after work accidents and other medical emergencies compared to standard population. This raises the question how a professional emergency medical coverage can be provided underground, taking into account lacking medical professionals in small resource companies combined with long rescue times. Aiming on the closure of this gap, a team of the mine rescue brigade from the Research and Training Mine Reiche Zeche (Forschungs-und Lehrbergwerk (FLB) Reiche Zeche) of the TUBAF Technische Universität Bergakademie Freiberg in Freiberg/Germany and its cooperating emergency departments of the Freiberg District Hospital and the Zeisigwaldkliniken Bethanien Chemnitz developed a totally new rescue concept using elements from tactical medicine and advanced emergency medicine combined with a specifically designed compact equipment and a highly standardised teaching curriculum. A fully new standardised and condensed tactical medical approach was developed including specifically adjusted equipment, and was taught in a didactically optimised way within 16 lessons in two days. Objective Structured Practical Examinations (OSPE) using manikins and simulated patients were conducted and compared to the identical exam of the reference group, which consisted of advanced paramedics. The standardised tactical medical scheme includes vital functions and body checks, advanced life support, nasal and intraosseous drug application, supraglottic airway management, artificial ventilation, thoracocentesis, bleeding control including tourniquet, fracture repositioning and splinting, transport bedding and thermal preservation. The developed Tactical Medical Mining Rescue (TMR) concept was subsequently included in the German guidelines for mine rescue services in 2022 and is already implemented in many companies in Germany and several international projects.

Sep 1, 2024

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Burman B. C

This paper describes studies into two particular aspects of the Lochiel deposit which formed part of feasibility level geot2chnical and hydrogeological investigations for proposed open cut mine development. The two aspects were depressurisation of thick beds of silt located through the profile and the determination of characteristics and origins of soil structure and their effect on pit stability. The studies were very detailed and multi disciplinary and highlight the integration of geology, geotechnics, hydrogeology and mining that is required for mine development studies. It is considered that as more marginal deposits are developed throughout the world the demands for efficient economic mining together with in- creasing scales of operation will require simi- lar types of studies. As such the studies pre- sented herein are likely to be a forerunner to a,emerging trend for development of open pit mines in difficult ground and water conditions.

Jan 1, 1986

By Quayle J. E

This paper covers period from 1973 through to 1988 and the mines of West Coast Mines, Elur Mine, North Mine and Risdon Zinc Smelter, now all part of the Pasminco Group. During this period, optimisation started with one mine (West Coast Mines) producing four Product concentrates with constant steady feed to the smelter and progressed to three mines producing eight products and a smelter varying feed inputs to maximise benefits. The initial optimisation was done manually using a desk top calculator and hand drawn graphs. This ultimately advanced to the use of PC plus linear programming software and spreadsheet generating relevant graphics. The financial benefits were achieved with no capital expenditure and increased from an initial $0.5 to $1.0 M/year (1973 $'s) to $5 to $10 M/year (1988 $'s).

Jan 1, 1991

Grinding is probably the single unit operation that requires the largest capital investment and operating costs in an ore beneficiation plant. Because of that, a great deal of research has been concentrated in the theory, design and operation of grinding equipment, in particular ball mills. To-date, the models developed to describe grinding in tubular mills are macrophenomenological and can be divided into two categories: energetic and kinetic models. This paper presents a new approach to modelling ball mill grinding: The Operational Model. The theoretical aspects of the model as well as a comparison with existing ones are discussed. The concepts of the model, summarised in easy-to-operate PC programs, permit the calculation and design of new ball mills, and a critical evaluation and optimising of mills in operation.

Jan 1, 1993

By S Thacker, M Noakes

The Newmont Tanami Operations (NTO), formerly the Granites Gold Mine, commenced operation in the mid-1980s with tailings deposition evolving over the past three decades as production has increased and the operation has expanded. Paddock-style tailings storage facilities (TSFs) and in-pit tailings deposition have fulfilled the tailings requirements for NTO over its lifetime with the technical specifications of these facilities improving over time in line with the positive development of standards, guidelines and best practice.This paper reviews the options for tailings storage facilities at NTO and the many considerations that have been analysed and deliberated upon before settling on specific TSF types and designs. It also explains the operating philosophies of the tailings deposition and how the facilities have always strongly maintained the optimum capture and retrieval of water. The current TSF design and criteria is presented, along with the introduction of dry tails harvesting for use in paste production as a backfill product for the underground mine. Tailings deposition and recovery remains a critical function of the Granites process to ensure long-term operation and gold production.CITATION:Thacker, S and Noakes, M, 2015. Newmont Tanami Operations – tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Y Xie, L O’Connor, S C. Dominy

"Sheeted vein gold deposits are characterised by multiple subparallel veins and free milling gold. In situ heterogeneity of mineralisation results in grade and process parameter variability, which will increase project risk. Measured variability is often enhanced by poorly designed sampling and test work protocols. Protocols that are optimised within the framework of the theory of sampling to suit the ore type, together with quality assurance/quality control systems, will reduce variability and provide fit-for-purpose results. The geometallurgical approach requires spatially distributed samples within a deposit to support variability modelling. Diverse attributes from core logging, mineralogical/textural determination and small-scale tests are used to measure variability. This contribution emphasises early stage geometallurgical intervention during project development. It presents a discussion of representative sampling in the context of the theory of sampling. A case study presents a protocol that exemplifies how data can be gained from a well-designed and planned program to support a resource estimate and prefeasibility study.CITATION:Dominy, S C, O’Connor, L and Xie, Y, 2016. Sampling and Test Work Protocol Development for Geometallurgical Characterisation of a Sheeted Vein Gold Deposit, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 97–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Xstrata CopperÆs Mount Isa Copper Operations is located in mineral rich north-west Queensland and is one of the largest sources of copper in the world. This world-class underground operation is planned to produce over 6.6 million tonnes of copper ore in 2007 from the X41 and Enterprise Mines. With an underground mining history of over 50 years and underground reserves of over 83 million tonnes at 2.6 per cent copper, mine planning for the future becomes an exciting challenge for the technical team due to the older nature of certain areas. The 1100 Orebody of the X41 mine was one of the first places that copper mining occurred, with its discovery in 1953 - 1954 and mining commencing in the 1960s. Sublevel open stoping mining methods have been employed since that time as the means of extraction, using a primary-secondary sequence to maximise stope turnaround time. Large Transverse Pillars within the 1100 orebody were not mined out in order to provide access for ventilation, power, orepasses and other services. The Panel Pillar, 4180XC and 4010XC pillars are three such Transverse Pillars in the 1100 orebody that will be mined as a final retreat. This paper discusses the technical challenges and issues associated with the extraction of Q390 stope, one of the stopes located in the Panel Pillar, and the design solutions to overcome these issues. Managing the exposure of backfilled stopes of variable fill strength, ensuring the stability of the crown, stope walls and drawpoints, managing vertical openings, re-establishing service networks, and stope filling are the critical issues given consideration for the final design of Q390 stope and other such stopes within a Transverse Pillar. Communication and coordination between the different departments in the mine are essential for the necessary work to be completed in a timely manner to bring pillar stopes into production.

Jan 1, 2007

By J E. Everett, D Linden, P Maney

In response to the implementation of a new schedule for iron ore fines in the International Maritime OrganizationÆs (IMO) International Maritime Solid Bulk Cargoes (IMSBC) Code, improved measures for the management of moisture have been developed. In particular, prediction of cargo moisture allows management of iron ore fines within the supply?chain to facilitate the safe?shipping of iron ore fines.An ARIMA model, augmented to allow for shipment tonnage, has been developed to predict the moisture level from previous shipments of the same product. The model explains about 60 per cent of the moisture variance. It was found that inclusion of other available information, such as ore composition, train/rake assays and recent rainfall at port and mine, did not add to the predictive power of the model.CITATION:Everett, J E, Linden, D and Maney, P, 2013. Predicting iron ore fines shipment moisture, in Proceedings Iron Ore 2013 , pp 17-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M P. Sandy, J B. Albrecht

"Narrow vein mining can be loosely defined as mining operations involving orebodies with a true thickness of less than 4 m. Some authors have limited the term to steeper-dipping orebodies where the ore will rill under gravity. However, ænarrow veinÆ can also legitimately refer to some of the flatter orebodies, such as many of the platinum, chrome and gold deposits of Southern Africa, and several in Australasia including Bullen (at Norseman), Sunrise Dam, Telfer (Patterson, 1993) and the famous æflatmakesÆ at the Emperor Gold Mine in Fiji (Gordon and Harmse, 1993). Where the orebody dip is less than about 40¦ additional effort is usually required to remove the broken ore, including the use of scrapers, hydraulic monitors or remote-operated excavators (Tombs, Buckingham and Hancock, 2008).Working in such narrow orebodies presents particular operational and geomechanics challenges. A range of mining methods have been developed or adapted to exploit narrow orebodies including:cut-and-fill,narrow vein bench or longhole stoping,Alimak stoping,shrinkage stoping, and methods for shallow dipping orebodies (including Airleg and mechanised methods).The paper discusses some of the advantages and disadvantages of each method with a focus on geotechnical aspects including mining sequence options, stress management, ground support requirements, dilution and recovery.CITATION:Sandy, M P and Albrecht, J B, 2012. An overview of geotechnical issues in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 185-194 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By D Craw, J Pope

The Greenland Group, Westland, can be characterised with respect to environmental issues by the application of a GIS database (DAME), and specific sampling campaigns. Waters draining gold mineralised areas have a distinctive chemistry characterised by neutral pH and arsenic as a trace element. The acid neutralising capacity (ANC) from carbonates usually exceeds the maximum potential acidity (MPA) from sulphides resulting in circum-neutral pH. These waters are readily distinguishable from waters draining coal mine related areas, which commonly have low pH (~4) and low As concentrations (~0.1 ppm). In contrast, dissolved arsenic mobilised from Greenland Group historic gold mining areas is up to 2.4 ppm. This As mobilisation is controlled by the secondary As mineral, scorodite (FeAsO2+2H2O). Maximum dissolved As concentrations increase with increasing pH, corresponding to the increasing solubility of scorodite with increasing pH. Dissolved As is attenuated by dilution, precipitation of scorodite, and/or adsorption to iron oxyhydroxide (HFO). Adsorption to HFO is an important attenuation mechanism in and adjacent to many mine sites. HFO is abundant at mine sites where pyrite was abundant in fresh rock, such as where the mineralised zone is dominated by disseminated pyrite. Pyrite, and resulting HFO, are relatively rare where mineralisation occurred as well-defined quartz veins. Localised HFO occurs also where ankerite oxidises in host rocks. Arsenic output flux (ca. 25 g/day) from historic gold mine sites is commonly less than the natural background flux from mineralised rocks (>5000 g/day).

Jan 1, 2006

By D Engelhardt, G Lane

The Cadia mine has shifted from an open pit operation to the Cadia East underground panel cave. The resulting increase in milled tonnes, more competent ore and the decrease in fines production through shifting to panel caving were predicted to require an increase of over 25 per cent in installed power. This expansion was accomplished via the installation of secondary and high pressure grinding rolls (HPGR) crushing of the ore, with the semi-autogenous grinding (SAG) mill receiving a combination of primary, secondary and HPGR crushed feed. This design, criteria and rationale for selection was presented at the SAG Conference 2011. This paper reports on the initial impact of secondary and HPGR crushing on the circuit performance with the new panel cave feed.CITATION:Engelhardt, D, Lane, G and Powell, M S, 2014. Cadia expansion – the impact of installing high pressure grinding rolls prior to a semi-autogenous grinding mill, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 233–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

By Kasai H, Hibi T, Matsuishi S

Coal oil mixture (COM), a liquid fuel pro- duced by mixing together coal and heavy oil on the 50-50 basis, has been brought to a level of practical use in Japan, being actually employed by a oil fired system at Yokosuka Thermal Power Station of The Tokyo Electric Power Co., Inc. A COM Production Plant, built in Onahama which is located about 160 miles from Yokosuka, required COM to be transported by sea. Mitsubishi Heavy Industries, Ltd. therefore performed a series of studies to develop a spe- cialized COM carrier, the world's first of its kind. Long lasting high stability is of pri- mary importance to successful use of COM. Much have been done in the way of research on stability of COM in the static storage, and the mechanism of COM static: stability is almost completety known. On the other hand, the knowledge about the COM dynamic stability, such as the stability while being transported aboard the COM carrier at sea, is still limited at the moment. The motion of COM aboard the COM carrier and how COM would settle were studied by tests. A visualization test on the COM behavior under dynamic motion was also performed and the mechanism of COM dynamic stability was analysed. The tests showed that the ship rolling motion had @n effect of promoting the settling of coal content of COM in the cargo hold. And studies were also made to device a method for esti- mating the settling quantity of coal during sea Transportation.

Jan 1, 1987