Search Documents

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P N. Holtham

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre (JKMRC), techniques have been developed to measure the electrical properties of the various minerals. The measured values will be used to model the behaviour of the various minerals in high-tension roll and electrostatic plate separators. The resistivities of ilmenite, rutile and zircon from a number of Australian producers have been measured by applying a DC voltage across a test sample and measuring the resulting very small current flow. By appropriate design of the measurement cell and attention to the experimental procedure, reproducible resistivity values have been obtained, ranging from 106Ωm for ilmenite to 1013Ωm for zircon. However, the conditions of measurement are radically different from those under which electrical separation takes place. It is not certain that the measured values reflect the resistivities seen under high-tension separation, during which the particles are subject to a high intensity corona field. Consequently, an alternative technique for measurement of resistivity under conditions of corona bombardment has been developed. It is based on the experimental procedure of Castle and Yelle (1979) used to measure the resistivity of fly ash under the conditions occurring in electrostatic precipitators. This paper describes the development of the segmented ground plane measurement surface and a high-voltage switched resistor network which comprises the in situ resistivity apparatus. Results are presented comparing the measurements made under corona bombardment with those made using the DC measurement cell. The equipment has also been used to study the current distribution from a corona wire, as a function of high-tension voltage and wire-to-plane spacing.

Jan 1, 2001

By J L. Mauk

Gladstone Hill, a volcanic-hosted low-sulfidation epithermal prospect in the Coromandel Peninsula, is less than 1 km from the world-class Martha Hill Au-Ag deposit. Gold-silver-bearing quartz veins occur in Late Miocene andesitic volcanic rocks of the Waipupu Formation that are extensively altered. The occurrence, spatial distribution and temporal relationships of hydrothermal minerals have been determined along two cross sections that transect the Amaranth, Gladstone, Cowshed and Moonlight veins. Quartz and pyrite are ubiquitous along these sections. Adularia and chlorite are widespread, but both are scarce in wall rocks adjacent to the Moonlight and Cowshed veins. By contrast, rare hydrothermal albite and epidote are restricted to wall rocks surrounding the Amaranth vein. Illite, which replaces adularia, is widespread and grades laterally eastwards into a zone of interstratified illite-smectite that envelops the Moonlight and Cowshed veins. During late-stage hydrothermal activity, rare calcite formed at depth and uncommon kaolinite and alunite formed at shallow levels. The overall clay mineral zonation with illite grading eastward into interstratified illite-smectite reflects paleothermal gradients of >220¦C to -170¦C towards the margin. The alteration assemblage of quartz, adularia, chlorite, albite, epidote, illite, interstratified illite-smectite and pyrite reflects formation from a near-neutral to weakly alkaline pH chloride water that contained low concentrations of CO2, Late calcite formed from very local descending steam-heated CO2rich water, whereas the rare assemblage of kaolinite and alunite formed from shallow steam-heated acid-sulfate water. Analysis of the available data indicates that the Martha Hill deposit and the Gladstone Hill area formed within a single large geothermal system. We infer that the Martha Hill deposit formed in the main upflow zone, whereas the Gladstone Hill area may have formed adjacent to this upflow zone.

Jan 1, 2001

By J Visser

Dust mitigation has long been seen as nothing more than managing a nuisance issue, but the reality is that poor dust management can lead to one or more of the following negative consequences: an increased risk of safety incidents, lost revenue, reduced and possibly even lost licence to operate, regulatory intervention, high staff turnover and/or absenteeism and occupational health and safety (OH&S) issues. Dust mitigation and management is not a black art; rather it is a scientifically driven process that can provide an opportunity to increase profits, increase the companyÆs status as an excellent corporate citizen, enhance staff retention and reduce the safety risk profile of the operation.The way to achieve success in dust mitigation and control is to apply the scientific method to each problem that can arise and plague any operation by using current industry best practice. This method of dust problem-solving can be applied to dust issues arising from specific dust sources and locations. The dust sources can include wind impacting on stockpiles, open areas, tailings storage facilities, moving train and truck loads, vehicular traffic on roads, the operation of shovels, front end loaders, draglines and other equipment, as well as ore movement on conveyors.The solutions will come from a combination of deployment of dust collection equipment, dust and moisture monitoring equipment, the appropriate application of water and chemicals, the introduction and maintenance of appropriate barriers and the use of predictive data from local and public weather stations. The paradigm shift required is to view dust mitigation as one aspect of normal operational practice, not a ænice to haveÆ or æunnecessary expenseÆ as most operators currently view it. This attitude is becoming more important as more and more local communities oppose the development of mines. One of the reasons for this local opposition is the inevitable dusty environment that is usually associated with mining.Dust mitigation is not a significant expense if correctly designed and included into the system, either as part of the original design of the operation or as a brownfield installation after the fact. Indeed, there is always a loss of revenue associated with dustiness resulting from ore movement and avoiding this goes a long way to paying for any associated dust mitigating costs.CITATION:Visser, J, 2013. Dust mitigation - changing the paradigm, in Proceedings Iron Ore 2013 , pp 27-38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

Ladies and gentlemen, distinguished guests and fellow members of The AusIMM, good morning.   Thank you for the opportunity to address you all today, Crown Minerals are very pleased to be associated with the conference again this year, and I commend the committee on their organisation and delivery of this yearÆs event.   As you can see from the topic of my discussion, I would like to broach the subject of collaboration between ourselves û Crown Minerals û and you our clients, and convince you that we are on the right track but can each do more.

Jan 1, 2007

With the advent of the resources boom in the late 1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large scale Australasian open pit mining generally.

Jan 1, 2002

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

DML Resources Limited - Mining Division produced over 50 000 oz of alluvial gold in the 1995 - 1996 year from five operations located in the West Coast and Otago Regions on the South Island of New Zealand. DML Resources Limited - Mining Division have a twenty year history of alluvial gold mining development in New Zealand. Recent expansions have seen the establishment of two operations in Chile whilst exploration continues in Bolivia, Peru and Argentina. The overseas growth is based on a stable production base in New Zealand focussed on the West Coast and Southland/Otago present and future operations. DML Resources consider that the mining potential in the Arahura Valley on the West coast will be fundamental to their New Zealand operations for some time. Collectively the plants operating in this catchment are referred to as the Poutini Project. Recent and late Pleistocene gravels derived from the erosion of the Alpine Schists running parallel to the Alpine Fault located on the Pacific/Australian Plant boundary are thought to be the sources of the alluvial gold in the Arahura and adjacent catchments. These gravels have been extensively mined for the past 130 years yielding some six million ounces over this period. Production from the Poutini Project started in 1989 and stood at approximately 35 000 oz for the 1995 - 1996 year. This production was split among three plants each working different areas of the deposit. Recovery techniques from each of the plants are fundamentally the same. Gravels are fed to a floating treatment plant where, following screening, the gold is recovered using jig plants and knudsen bowls. Overburden to wash stripping ratios vary between zero and seven to one with plants treating between 80 and 250 cubic metres per hour. Restoration of the land following mining is undertaken progressively. All land in the Poutini Project area mined to date has been restored to a standard suitable for dairy farming purposes. The Poutini Project is a cooperative venture between the Maori landowners and DML Resources Ltd. The Arahura River has particular cultural significance to the Maori as it is the source of the much valued greenstone or pounamu a type of jade valued for jewellery and tools. The Poutini Agreement was signed in 1989 setting out the role of each party in the mining of the Arahura and adjacent lands. Current exploration and development should extend the resource to allow mining to continue on the Poutini project for an additional three to five years at current gold prices. Production within new Zealand beyond this point may be compromised by increasing difficulty in gaining access to prospective areas within New Zealand, lowered margins due to high New Zealand dollar exchange rates and the overall lowering of alluvial headgrades throughout the West Coast and Otago/Southland regions. To counter these effects DML has continued to improve on operational efficiency and performance monitoring to optimise the mining practices used. This paper detains the background to the Poutini Project, the geology, plant and equipment used together with descriptions of the current mining methods employed.

Jan 1, 1996

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

The injection of grouting compounds into the consolidated rock surrounding underground mine workings has long been practiced for the purpose of sealing against water flows. In more recent times however, grout injection has also found application for the purpose of rock mass reinforcement. Mines in Europe,America, Australia and elsewhere now make use of significant quantities of chemical grouts in both preventative and remedial strata control work.   Despite the increasing usage of grouting for these purposes, there is limited knowledge about the effects of grout injection on the rock mass, and acceptance of the method is by no means universal. In some cases grouting has been applied with little understanding of the factors that control its effectiveness, and disappointing results have been obtained.   This paper reviews the basic concepts of how grout injection may contribute to the control of rock surrounding underground mine excavations, and highlights the factors which may serve to limit the efficacy of the method and the uncertainties that complicate the appraisal of grouting as a method of strata control.

Jan 1, 1994

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.      Martha, 2.      Welcome, 3.      Edward, 4.      Empire, and 5.      Royal.   Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (< 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (< 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006

In a modern economy there is a compelling case why governments should not own property rights to mineral deposits. Assuming they do, however, governments will use these constitutional rights to raise revenue. They have two basic instruments to achieve this; a royalty charge on price or a rent tax on income/profits. On the one hand, a royalty charge creates a 'deadweight loss' to society by increasing cut-off grades and decreasing the life-of-mine. They are also regressive. However, they are easy to administer. On the other hand, a rent tax avoids the problem of 'deadweight loss'; it does not impact on the life-of-mine because the tax structure is neutral. But, they are difficult to administer correctly, particularly in the determination of rents and the definition of mining per se. If rents are incorrectly determined capital markets are distorted. And, if mining activities are incorrectly defined, downstream activities could be adversely affected.

Jun 1, 2010

By S C. Dominy

This contribution examines the effect of feedstock sampling before the sorting stage of polyethylene terephtalate (PET) bottle recycling. Batches of waste PET bottles may contain non-PET bottles which need to be removed by sorting. Any residual presence of PVC is detrimental for the quality of products manufactured from recycled PET. The maximum tolerated concentration of PVC in cleaned PET is extremely low, which places high demands on the recovery of PVC achieved by sorting. To be confident of attaining the desired PET quality after sorting, acceptance sampling of truckloads of PET bottles may take place prior to sorting. It is shown that accounting for sampling uncertainty requires that the sorting process achieves a consistently high recovery of PVC bottles.CITATION:Glass, H J and Dominy, S C, 2017. Plastics recycling and sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By McKenzie A. M

The Corridor ore body is so named because it occurs in an east-west zone or corridor of schist bounded on the north by the siliceous conglomerates of Mount Lyell, and on the south by similar conglomerates of the Tharsis ridge (Fig. 1). It was discovered after the geophysical prospecting methods described below had defined a target zone for diamond drilling.Since the proving of copper mineralisation by drilling, the corridor orebody has served the vital function of a convenient known target body for the orientation of more recently developed geophysical methods. Traversing of the orebody by these new methods has provided experience for the evaluation of anomalies elsewhere.Some of the methods applied had not been used in Australia before, and were introduced to the west coast of Tasmania through the undertaking there of modern regional exploration programmes. The authors feel that the information gained could be of assistance to others engaged in geophysical prospecting.HISTORY OF DISCOVERYProspecting in the Mount Lyell district has been more or less continuous since 1881. The first geological report was published by Thureau (1886).In 1934, Blazey and Douglas (1934-38) commenced geophysical surveys at Mt. Lyell using the equipotential method.They obtained anomalous indications in several discrete zones and actually detected the south-east half of the corridor orebody but their work never became the basis for...

Jan 1, 1961

A detailed study of the capital investment and production cost for copper electrowinning plants shows that significant savings in both can be achieved by increasing the current density. From the economic analysis it is determined that the optimum current density which will result in lowest capital investment and lowest operating cost is between 60 A/sq. ft. and 70 A/sq. ft., or at least three times as high as the Conventionally employed current density. The specific investment, expressed as $/ton-year, is found to be a function of both the current density and plant capacity and has a minimum value at the optimum current density. Empirical equations are developed for the purpose of estimating the capital investment and operating cost for plants of any production capacity operating at any current density.

Jan 1, 1972

Reason Analysis of Impurity Containing and Technology Discussion of Quality Improvement for Low-Quality Iron Concentrate

Sep 13, 2010

By Lamont G

The significance of blasthole stemming in determining blasting efficiency has been extensively studied for small diameter holes using gelignite explosives. Recent developments in blasting technology with the use of large diameter holes and low cost blasting agents have not included studies of the effectiveness of different types of stemming materials. A review of previous measurement techniques and the relevance of these earlier results to present stemming practice is presented in this paper. A survey of operating mines in Australia provided information for this analysis. The value of stemming in reducing blast noise and improving blasting efficiency is generally accepted but the use of bulk-loaded explosives in underground operations has resulted in the practice of eliminating the use of stemming material.In surface operations drill cuttings are used for stemming on the basis of availability rather than efficiency in providing resistance to movement. The development of laboratory testing techniques, based on noise level and borehole pressure measurements, to evaluate the relative efficiency of different types of stemming materials is described. The results of an extensive series of tests with ANFO explosive showed similar trends tothose obtained from earlier published results with gelignite type explosives. Conclusive quantitative results on the relative effectiveness of different stemming materials will require minor modifications to the existingequipment. Observations and the results of pressure measurements indicated the presence of shock wave effects which caused the ejection of the top section of the stemming column when using coarsely fragmented material.

Jan 1, 1979

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (lMR) separators. The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.   The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990