Search Documents

By Luther W. Lennox

During the last few years, one of the great problems in the milling of all ores has been that of grinding. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of grinding to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of grinding methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative grinding resistances of a number of ores now being milled in this country and Alaska, the manage-mxitofthe Portland mills requested Samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh screen; in the screen analyses tabulated and plotted herewith, the 150-mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves. The experimental grinder was a small iron tube-mill, 8 by 121/2 in., in which was placed a definite number (74) and weight (3450 gm.) of 3/4-in. steel balls, 1 Ib. water and 1 Ib. ore. To obtain uniform conditions, each ore was first crushed and screened, and from the sized products a "standard feed" was artificially prepared, the same standard being adopted for all tests in that particular series. The prepared feed was

Jan 1, 1920

By U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laist1 says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say ¼ in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly wide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consumption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By A. G. Taylor, H. P. Ehrlinger, U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laistl says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say 1/4 in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly aide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consurnption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By Harwick Johnson, E. W. Schilling

THE separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Probably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1935

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott's Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By J. E. Hilliard, H. E. Cook

It is shown that for systems having a miscibility gap the spinodal composition (c,) in the vicinity of the critical temperature (Tc) is related to the equilibrium composition (c,) by where cc is the critical composition. This expression is exart for the limit T — Tc and is a good approximation down to (T/Tc) - 0.9. If the miscibility gap meets the composition of the pure components THE recent theoretical treatment by cahn1,2 on spinodal decomposition of solid solutions has revived interest in methods of estimating the chemical spinodal, * i.e., the locus on a binary phase By use of the appropriate expression, the spinodal can be drawn on the Phase diagram almost by inspection with an accuracy comparable to that of lengthy calculations in which a free-energy function is fitted to the phase diagram. Satisfactory agveemenf is also obtained with spinodals comPuted from experimental free-energy curves. where G is the Gibbs free energy of the homogeneous solution and c the atomic fraction of component 2, the derivative being evaluated at constant temperature (T) and pressure (P). (These subscripts will hereafter be omitted from the partial derivatives.) If experimental measurements of G as a function of c and T are available in a single-phase region above the spinodal, then these can be extrapolated to obtain a series of metastable free-energy isotherms in the two-phase region, and from these isotherms a series of spinodal compositions can be calculated. Because the value of is very sensitive to experimental errors, an elaborate analytic procedure is required for

Jan 1, 1965

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By W. M. Rutherford

A knowledge of the limits of miscibility between reservoir oil and possible injection fluids is required for selection of the optimum miscible-injection fluid. Limits of miscibility can be estimated from the results of equilibrium phase-behavior experiments. They can also be determined by means of displacement experiments conducted in a high-pressure sandpack. This paper describes the equipment and procedure which have been developed for determining miscibility conditions by stable displacement. A systematic series of displacements of a West Texas reservoir oil was carried out. The results indicate that, at constant pressure, miscibility is a function only of the pseudocritical temperature of the injection gas. This fact, together with improved experimental methods, makes the displacement technique a rapid, reliable means for determining miscibility conditions. In conjunction with the displacement experiments, phase diagrams were constructed for the oil with dry gas and propane and with dry gas and ethane. Phase behavior of the methane-ethane-propane system was determined at 110°F. The experimental work demonstrates the feasibility of using ethane-rich gases to reduce cost and pressure requirements for miscible displacement. INTRODUCTION In recent years, interest in the miscible displacement of oil by light hydrocarbon mixtures has been high. Many pilot and a few field scale projects have been started.1 These projects have made use of various methods for achieving miscibility: (1) the LPG-slug process, (2) the enriched-gas-drive process and (3) the high-pressure gas-drive process. Some field projects have been successful; the results of others are debatable. In general, projects which have performed best have involved the injection of an appreciable fraction of a pore volume of miscible material. Economical application of miscible displacement depends strongly on the cost of the miscible-injection fluid. If an appreciable fraction of a pore volume of material is required for successful application of these methods, a precise knowledge of the minimum requirements for miscibility in terms of composition of injection fluid is essential. Therefore, reliable experimental methods for determining miscibility conditions are important, and a procedure for estimating these conditions from the composition of the reservoir fluid is highly desirable. The subject of this paper is the problem of determining conditions which result in miscible displacement of oil by light hydrocarbon mixtures. Miscibility conditions can be estimated by means of equilibrium experiments conducted in a PVT cell, or they can be determined by means of high-pressure displacement experiments. This paper describes the equipment and procedure which have been developed for the determination of miscibility by high-pressure displacement experiments. These methods have been applied to the displacement of a West Texas reservoir oil with mixtures of dry gas, ethane and propane. In conjunction with the displacement experiments, triangular phase diagrams have been constructed for mixtures of the oil with dry gas and propane and with dry gas and ethane. The effect of injection-gas composition on conditions for miscible displacement in high-pressure sandpacks and cores has been the subject of several published papers.2-5 The experimental methods used in these investigations were such that displacements were unstable, and the effects of fingering and/or gravity layover are clearly evident in the results. Miscibility conditions were probably correct in spite of the instability phenomena, but the experiments evidently were time-consuming, and limited data were reported. Systematic high-pressure flow studies which would support a correlation of miscibility conditions have not been reported; however, Wilson5 has proposed the use of pseudocritical temperature of the injection gas as a parameter and Benham, et al,6 have based a miscibility correlation on observed and calculated equilibrium data.

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

By John Goheen

RECENTLY the head burner at a brick. plant with over 40 years' experience said that he had burned brick by guess for over half his lifetime and had used pyrometers for 2 1/2 years but hoped that he would never have to burn kilns without pyrometers again. The ceramic engineer in making a special study of the burning of clay ware and the effect the heat of the kiln has on color and vitrification is also rapidly placing the burning of clay on a twentieth-century basis. Clay ware may be divided into various groups, brick and drain tile; sewer pipe; firebrick; and pottery, which, in turn may be subdivided into special classes. As nearly as the analysis of the clay type of kiln, etc., will allow, there are practically the same problems to solve in burning in all of the processes or operations. The underlying objective is the same, namely the production of the best grade of ware under the most efficient and economical manufacturing system. The principal problem in the production of clay ware is the burning off of the kilns. The most modern steam shovel may dig the clay and the most advanced types of pug mills and wire cut machines or molds of various kinds may be installed, but unless the drying and burning of the ware is successful, all of the previous operations will be useless. On this final operation depends the entire result of the plant. In reality, burning of all. clay ware is purely a heating proposition. The kilns, or furnaces, should be so designed as to give equal distribution of heat. Consequently, the problems of design and construction of kilns to produce equal distribution of heat require serious consideration, as do also the questions of heat control and draft control. The three most important factors in the burning of practically all types of kilns may be

Jan 9, 1919

By Nathaniel Herz

The use of zinc dust for precipitating the pecious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been done o,n methods of testing zinc dust, as yet. no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some obscrvations made while testing a large variety of zinc-dust samples in the laboratory. W. J. Sharwoodl has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J E Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of 99 %' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more XCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 CC. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grams of pure crystallized XAg(CN)2 may be dissolved in a liter of water and 1.5 grams XCN added. " Weigh out 0.5 gram zinc dust into a 300-cc. beaker. Add a few cubic centimeters of watcr and stir until zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, place in a scarifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efflciency."³

Jan 1, 1916

Cobriza can only be described as the Machu Picchu of the mining business. This relatively new mine of the Cerro de Pasco Corp. in Peru, subsidiary of The Cerro Corp., was put on stream in December 1967. The best way to get there is to go in the company's HelioCourier with pilot Paco Perez. The plane is mostly engine and the pilot is without nerves. The trip starts at an elevation of 12,000 ft at La Oroya and ends at the Cobriza air strip near the top of the Continental Divide at 14,200 ft. Perez says this is the highest air strip in the world. The flight is made at an altibude below many of the peaks and it is easy to pick out the Inca Trail which follows the ridge line of the top of the Andes. Inca ruins are also visible from the aircraft. The drainage pattern, with a surprising number of lakes and rivers, can be seen and so, too, can a great deal of structural geology and numerous agricultural settlements dotting the altiplano. Cobriza is in the monta[n]a on the east side of the Andes, which is characterized by tropical climate and vegetation, an abrupt change from the frosty mountain atmosphere. The mountainsides are precipitous and the bottoms of the steep valleys are channels for roaring rivers. Such is the setting of Cobriza, above the swift cataracts of the Mantaro, benched out precariously at about 8700 ft elevation. The mountains rise in majestic splendor and the sun comes up late and sets at 3: 30 on winter afternoons. One of the lowest of the Cerro de Pasco camps, it is the most remote.

Jan 11, 1969

By Waldemar Lindgren, Clyde P. Ross

To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron CO.; to George W. Pfeiffer, General Manager, and to the several members of his staff. Geological Features of the Sierra Maestra For our knowledge of the geology of the Sierra Maestra we are indebted to reconnaissance work by Fernandez de Castro, R. T. Hill, Mr. C. Hayes, T. W. Vaughan, and A. C. Spencer. The summary by the latter three geologists furnishes the best guide to the region.' The range is undoubtedly outlined by a great east-west dislocation. Its southern slope drops abruptly to the sea, while on the north side a much gentler declivity leads down to the rolling plateau of Tertiary limestone which occupies much of the adjacent part of the island. Viewed

Jan 1, 1916

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By D. P. Harris

This paper surveys a few of the quantitative exploration models that might be of interest to an ex-plorationist seeking to apply methods of operations research to mineral exploration. A general development of each model is presented, and the model is evaluated relative to the exploration activity. Finally, a philosophy of exploration and mineral resources is presented, and a possible exploration strategy incorporating concepts of some of these models consistent with this philosophy is proposed. The high cost of conducting an effective exploration program has generated an increasing interest in methods of optimizing the allocation of the resources of a firm engaged in mineral exploration. As a step towards this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firm's operations so as to optimize its profit objective. QUANTITATIVE MODELS General: Exploration models express at least two concepts: mineral occurrence and effectiveness of search. In simplest terms, an exploration model might be formulated mathematically as follows: P(X) = F(X) . G(X), where P(X) = the unconditional probability of discovery of X deposits, F(X) = the probability of occurrence of X deposits, and G(X) = the probability of discovery of X deposits, conditional upon their existence in the search area. With these general models as a basis of reference, some of the specific exploration models are examined below. The Allais Model: DEVELOPMENT - M. Allaisl performed the first study in which a philosophy of exploration was formulated into a probability framework. His objective was to estimate the economic profitability of the exploration of the Algerian Sahara. Allais divided the Algerian Sahara into blocks of land (called cells) 10 km square and defined the random variable, X, as the number of mining districts per cell. Thus, F(X) would describe the probability of 1, 2, or n mining districts occurring within any cell of the search area. Allais reasoned that his best information as to the form of the distribution, F(X), was the number of mining districts per cell that had been found in well explored areas in the world, such as the Western States of the U.S. He found that the Poisson function produced a reasonably good fit to the distribution of districts in these explored areas: where? is a parameter, such as the average number of districts per cell. Thus, by determining the value

Jan 1, 1968

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970