Search Documents

By Rudolf Gahl

SOME time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanuers in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to. be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but. varying the adjustments of the vanner .from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 2 3/8 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it .was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Sep 1, 1909

By John Birkinbine

" Whether an iron-ore should be roasted is a question which very seldom arises ; at least, this question seldom ought to arise. With the exception of the red impalpable oxide, the whole series of ironores require roasting—even the specular iron-ore, if it is very compact—but the best oxide, if too compact, works badly in the furnace. All other ores should be subjected to calcination. Some ironmasters are in the habit of using the hydrates raw, but this should riot be done where clay-ores are smelted or where the hydrates contain either chlorides or phosphates. But in the latter case, the pig metal will be cold-short if there is too much phosphorus. Under all circumstances, however, it is best to roast the ores if we expect good metal and well-regulated furnace operations. " The object of roasting ores is to produce higher oxidation and to expel injurious admixtures. In both cases liberal access of atmospheric air is required ; we should, therefore, so arrange our roasting operations as to fulfil these conditions, from which it will appear that different ores require different treatment."* The above may be considered an extreme, and perhaps erroneous view; but there is no question as to the absence of a general appreciation concerning the value of preparing ores of iron for smelting in the blast-furnace.

Jan 1, 1884

By J. J. Scott

INTRODUCTION Rock mechanics theory needs to be applied to solve ground control problems, but in the final analysis the mining method and equipment which is used will be those which solve problems in a practical manner. Equipment and its inherent productivity and safety as supplied as "off the shelf" items by manufacturers often dictate the size of mine openings. Operators may tolerate falls of ground and associated hazards if productivity and safety problems are not too severe. In this whole process the costs of mining finally dictates just what system will be employed and what equipment will be used. True solutions to ground control problems sometimes require that the mine operator step back and totally rethink his problems. The true cost of accidents are often missed and hidden in overhead costs. Losses in production and accompanying profit are not fully considered, false economics, such as using inappropriate roof support devices, are undertaken at times when using the most expensive devices to totally eliminate accidents may be the best overall solution. Automation to remove the worker from the hazard area is often over- looked as the initial capitol expense to apply it may be high. Cooperation between mine engineers, mine operators, safety personnel, equipment suppliers, and government inspectors, both state and federal, is required to reach workable solutions that best meet the goals of all parties.

Jan 1, 1983

By S. S. Hartranft

FuRnace-men of the present day agree very nearly as to the best cooling-devices for the protection of blast-furnace hearths and boshes, and the best location of the cooling-system in the brick-work for the maintenance of favorable furnacelines throughout the blast. The replaceable bronze and copper plates are practically faultless; and there seems to be no reason why a furnace-hearth and bosh should not be held in good condition, by intelligent management and the use of replaceable plates, for a period several times the length of the average blast of to-day. While furnace-men have taken these .precautions to protect the hearth and bosh beyond the life of the lining, the portion of the lining above the mantle has been partly protected by some and wholly neglected by others. Some would not construct a furnace without mantle-plates, and others would not construct a furnace with them. In most cases, furnace-men have either trusted to Providence or to the bosh-plates for the continuance of favorable working-conditions above the mantle, and the prolongation of the life of the lining; consequently furnaces are constantly blown out for repairs to the lining, or for relining, when the hearth and bosh are in good enough condition to last through another blast. The following extract from one of Mr. James Gayley's con-

Jan 1, 1901

By F. X. Meyer

THE United States Smelting Refining and Mining Company maintains an ore-purchasing department for procurement of custom tonnages of milling and smelting ores and concentrates for treatment at its Midvale plant. Arrangements with other companies provide for treatment of Company and custom zinc concentrates. Location of the Midvale plant in the heart of the Western mining country makes it possible to serve shippers from these nine producing states: Arizona, California, Colorado, Idaho, Montana, Nevada, Oregon, Utah, and Washington. Shipments from most of these states travel over main-line railroads, delivery being made at Midvale within a short time after billing of the shipment. Shipments varying in size from a few sacks to carloads can be handled at

Jan 1, 1948

By David R. Maneval, H. B. Charmbury

At the turn of the century, iron and coal were the keys to industrial prosperity. At that time, Pennsylvania was the leading mineral producer in the Country, producing 200,000,000 tons of coal in a typical post-World War I year. Close to 90% of the Nation's energy was generated by coal. Today, coal accounts for but 22% of the energy generated, leading to a drastic reduction in Pennsylvania coal output. In contrast with the post-World War I days, 1964 figures showed a drop in production to 93,846,480 net tons. This huge decrease has created a serious economic problem in a state so much dependent on the coal industry. Along with the reduction in coal production, employment has dropped considerably through these years (the number of miners alone has gone from 280,011 to 43,149), thus causing a heavy burden of supporting the unemployed on the taxpayers. As far back as 1939, coal operators and economists saw the problems on the horizon and the need for improvement. Realizing that research was a way to improve and stabilize the industry they demanded legislative action. The Legislature reciprocated with a small grant to The Pennsylvania State University with the provision that each State research dollar be backed with one from the industry. This initial grant laid the foundation for the further growth in coal research.

Jan 3, 1966

By A. M. Ribe

Briefly stated, the mission of the traffic manager (currently called a transportation services manager) is to enable his firm to utilize to its best economic advantage the various systems and modes of transportation available to it to bring in its raw materials and ship out its finished products. The function of the transportation services manager is perhaps of more relative importance in industrial minerals operations than in industry and trade generally.

Jan 1, 1970

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937

THERE is at least one concrete indication that Soviet Russia's two most important iron ore producing centers are seriously depleted. While keeping in mind Russia's penchant for reverse propaganda, one piece of evidence indicates that Magnitugorsk in the southern Urals and Krivoi Rog in the Ukraine have been mined to a point where lower grade ores are being recovered. An article in Pravda, Soviet newspaper, by I. P. Bardin. a Russian metallurgist, says that ore presently mined must undergo an expensive enriching cycle before it can be used in blast furnaces. Com- pounding Russian metallurgical troubles is the low quality of coking coals. High ash and sulphur content typifies the coal Badin talks about. Coal from the Ukraine, Eastern Siberia, Kazakhstan, and the Far East requires extensive treatment before it can be used, according to the article in Pravda.

Jan 7, 1953

By L. VOGELSTEIN

OUTSTANDING among the year's events in copper has been the reimposition of an import duty of 4r. per pound in this country which became effective June 21. In consequence of this action by Congress, the Ottawa Empire conference recommended a duty of 2d. per pound equivalent at normal rate of exchange to our 4c. duty, on all copper originating outside of the Empire. Lip to the middle of this year only Russia and Japan had a closed market; the import duty on copper in Russia is 30 per cent ad valoremm and in Japan about 2c. Russia's consumption has always been in excess of production and she has imported from 2(1,000 to 40,000 ton, of copper per annum. Japan, with a production of 6,000 to 7,000 tons per month, has absorbed, in normal times, its production, but during recent: sears has exported varyiug quantities in 1929. 2,200 ton-: in 1930, 2,700 tons, and in 1931. 3,600 ton-. Aside from the-e two countries, the international market has heretofore been free. It and when the British Empire duty become, effective the world's markets will be divided into four unit: 1. Russia and Japan, 2. United States. 3. British Empire. 4. Rest of the world. The world's production at present is rennin it the rate of 930.000 tons per annum. This year's production will be over 1,000,000 tons because the several curtailment did not become effective until the second quarter. consumption will be slightly in excess. Deducting from 30,000 tons Russia's and Japan's production of 121.000 tons, 806,000 tons is left divided a, follows:

Jan 1, 1932

By E. S. Leaver

The authors of the paper above mentioned have sent the following statement to correct erroneous com-ments and implications in their article with the re-quest that it be published: "In the above mentioned article the reference to Bendelari jigs is used in the generic sense as applying to the mechanically driven diaphragm jigs. No attempt was made to dif-ferentiate between the various machines as installed on different dredges. The Natomas Company use a jig of their own manufacture. The Yuba Company installed the Placer jig as manufactured by the Pan American Engineer-ing Company. "The Pan American Engineering Company also manufactures the Crangle jig under their own name. This is a diaphragm jig in which the pulsations are produced by intermittent flow of water through the patent Crangle Valve and it has no driving mechanism."

Jan 1, 1937

Jan 1, 1899

By AIME AIME

PLANS for the Semi-centennial Meeting have almost reached completion, although in any undertaking of such magnitude a few changes are always to be expected at the last moment. As worked out up to the time of going to press, the program of the meeting is shown below. The headquarters will be the Irem Temple, in Wilkes-Barre.

Jan 1, 1921

By R. E. Salvoti

IN underground coal mining, the increasing trend towards mechanical methods is ever apparent. Figures for 1939 showed that 28 per cent of the total bituminous coal production was mined mechanically 1940 statistic will reveal an even higher figure. Factors causing this trend are varied, but the important are the following;

Jan 1, 1941

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

By V. T. BERNER

THIS apparatus was designed primarily to meet the demand for a quick, efficient stopping to seal off the burning area temporarily during a mine fire, but it can be used in any circumstance where an immediate brattice is required for ventilation control. In using the old style brattice, mine-rescue workers have found it difficult, in smoke-laden drifts and stopes, to erect an effective stopping with wooden frame and canvas. Stulls must first be cut to the proper length, the canvas tacked in place, and the numerous irregularities of the walls and back must be caulked. This operation requires the employment of axes, saws, and hammers, which cannot easily and safely be handled in dense smoke. The fire fighters have often been forced to abandon their brattice, unfinished, because of the rapid approach of the fire, or because of the exhausted sup- ply of oxygen in their breathing apparatus. It is neces-

Jan 1, 1930

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely' that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:' the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.' The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943