Search Documents

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By C. R. Whitney, G. N. Maniar, D. R. Muzyka

Previous results have shown that Pyromet 860, an Fe-Ni-base heat-resistant alloy, is stable at temperatures as high as 1500°F for aging times as long as 100 hr. This Paper describes the results of long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Times as long as 37,660 hr were employed. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffraction, and microprobe techniques. phase, containing cobalt, nickel, and molybdenum, was detected after extended exposures from 1200" to 1400°F and careful study was performed to describe the kinetics of its formation in this alloy. µ phase formation apparently has little effect on the elevated-tem-perature properties of Pyromet 860. For times as long as 500 hr at 1300°F and below, with µ phase present, m significant effects on ambient temperature properties were noted. For longer times at 1300°F and after 1400°F exposure, the effects of u phase on ambient temperature tensile strength properties are not clear due to y' effects and grain boundary reactions. Electron-vacancy, N,, numbers were calculated using different methods described in literature and correlated with the present findings. In the selection of alloys for use in gas turbine applications, structural stability ranks as a primary criterion. High-temperature strength and cost are also of major concern. With these factors in mind, Pyromet 860 alloy, an Fe-Ni-base superalloy was designed. This alloy combines the cost advantages of Fe-Ni-base alloys such as A-286, 901, and V-57 with improved strength and structural stability'1,2 and no tendency to form the embrittling cellular 77 phase. A previous study3 reported on the stability of Pyro-met 860 at temperatures from 1375" to 157 5°F and times up to 100 hr. That study showed that the y' precipitates increased in size and separation and decreased in number with an increase in time or aging temperature. No deleterious phases were found to occur. In the present work, samples from four production heats were subjected to long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Various heat treatments were used on the starting samples and tests were run up to 37,660 hr. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffrac- tion, and microprobe techniques. Electron vacancy numbers, Nv , calculations were made by TRW.4 Experimental results are correlated with the Nv data used to predict occurrence of intermetallic phases such as a phase. EXPERIMENTAL PROCEDURE Mechanical Tests. Material for the present study came from four production size heats of Pyromet 860 alloy, weighing from about 3000 to about 10,000 lb. All of these heats were made by vacuum induction melting plus consumable electrode vacuum remelting. The nominal analysis for this alloy is compared with the actual analysis of the four heats in Table I. Sections of these heats were forged to 9/16-in. round bar,3/4-in. square bar, 3-in. round bar, 4-in. square bar, and a gas turbine blade forging about 16 in, long, about 6 in. wide, and weighing about 20 lb. In general, all forging of this alloy is done from a 2050°F furnace temperature. Longitudinal test blanks were cut from the centers of the smaller bars, from mid-radius positions for the 3- and 4-in. bars, and from the air foil of the gas turbine blade and heat-treated according to the procedures outlined in Table 11. Heat treatment A is the "standard treatment" recommended for this alloy for best all-around strength and ductility. Heat treatment B is a modification of treatment A for improved tensile strength at moderate temperatures. The treatment coded C was designed for treating large sections according to a procedure previously described.' Heat treatment D was developed to yield optimum stress relaxation characteristics at 1050°F for a steam turbine bolting application. After heat treatment, the test blanks were machined either to plain bar creep specimens with a gage diameter of 0.252 in., to combination smooth-notched stress-rupture bars with a plain bar diameter of 0.178 in. and a concentration factor of Kt 3.8' at the notched section, or to notch-only specimens. All specimens conformed to ASTM requirements. Metallography. Most of the creep-rupture tests were continued to failure. A few bars were fractured as smooth or notch tensiles after creep-rupture exposures. After fracturing, ordinary metallographic sections were made primarily in gage areas adjacent to fractures to represent a "high-stress" region and through specimen threads to represent a "low-stress" region. All metallographic sections were made in a longitudinal direction with respect to the test specimen axes. For optical microscopy, the samples were etched in glyceregia (15 ml HC1, 5 ml HNO,, 10 ml glycerol). For XRD analysis, the phases were extracted electrolytically in two media: 20 pct &Po4 in H20 for selective extraction of y' and 10 pct HC1 in methanol for carbides and other phases.

Jan 1, 1970

By L. G. Sprague

THE fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product finer. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1943

By W. L. Saunders

THE world's greatest producing area is, geographically, in the midland region of North America about the Great Lakes. This area, with but one- third of the nation's population, produces, with the exception of tobacco and cotton, three-quarters of the principal staples. It provides the surplus or export grain, meats, dairy products, steel and leading minerals. The social and political condition of a nation is determined by its industrial efficiency, and the share of the commerce of the world obtained by a nation is fixed more by the economy of its transportation than by any other factor. It is an economic maxim that: The total cost is the cost of production plus transportation cost. The cost of carrying 1000 tons by water or 100 tons by rail is equal, over the same distance

Jan 1, 1921

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By Alfred E. Hunt

By the death of Joseph Dame Weeks, past-President of this Institute, which occurred December 26, 1896, the world has lost an earnest and unwearied philanthropist; the Christian church, a zealous, active and consistent representative; the United States and the State of Penusylvania, a patriotic, pub-

Jan 1, 1898

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

INSTITUTE OF METALS DIVISION Ferrous and Nonferrous Physical Metallurgy (By-laws in Transactions, Vol 156, 1944) Established as a Division April 26, 1918 Walter A Dean, Chairman R. M. Brick, Past-Chairman Morris Cohen, Senior Vice-Chairman J H Scaff, Vice-Chairman Ernest Kirkendall, Secretary-Treasurer

Jan 1, 1952

Established as a Society February 26, 1957 John S Bell, President Wayne E Glenn, President-elect Basil P Kantzer, Past President R E Howard, Vice, President M B Penn, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Bldg Dallas 1, Texas

Jan 1, 1959

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By M. E. Lombardi

ThE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 81/4 in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling. The problem is to reach a depth of 4,000 ft. or more with a string of

Jan 1, 1915

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By F. C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected. If the balls added are too small, grinding efficiency is decreased by wasted contacts that are too weak to break the particles nipped; these largest particles are gradually worn down in the mill by the progressive breakage of corners and edges. Ball rationing is the regular addition of make-up balls of more than one size. The largest balls added are aimed at the largest and hardest particles. However, the contacts are governed entirely by chance, and the probability of inefficient contacts of large balls with small particles, and of small balls with large particles, is as great as the desired contact of large balls with large particles. Ball rationing should be considered an adjunct or secondary modification of the principle of selecting the make-up ball size to break the largest particle present. Empirical Equation In 19521,2 the author presented the following emerical equation for the make-up ball size: B - ball, rod, or pebble diameter in inches. F = size in microns 80 pct of new feed passes. Wi - work index at the feed size F. Cs - percentage of mill critical speed. S — specific gravity of material being ground. D == mill diameter in feet inside liners. K - 200 for balls, 300 for rods, 100 for silica pebbles. Eq. 1 was derived by selecting the factors that apparently should influence make-up ball size selection and by considering plant experience with each factor. Even though Eq. 1 is completely empirical, it has been generally successful in selecting the proper size of make-up balls for specific operations. But an equation based on theoretical considerations should be used with more confidence and have wider application. The theoretical influence of each of the governing factors listed under Eq. 1 was accordingly considered in detail, as described below, and a theoretical equation for make-up ball sizes was derived. Derivation of Theoretical Equation Ball Size and Feed Size: The basis of this analysis is that the largest ball in a mill should be just sufficient to break the largest feed particle into several pieces, excluding occasional pieces of tramp oversize. In this article the size F which 80 pct passes is considered the criterion of the effective maximum particle feed size. The smallest dimension of the largest particles present controls their breaking strength. This dimension is approximately equal to F. As a starting point for the analysis it is assumed that a 1-in. steel ball will effectively grind material with 80 pct passing 1 mm, or with F- 1000µ or about 16 mesh. The breaking force exerted by a ball varies with its weight, or as the cube of its diameter R. The force in pounds per square inch required to break a particle varies as its cross-sectional area, or as its diameter squared. It follows that when a 1-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle. This is in accordance with practical experience, as well as being theoretically correct. Confirmation of this reasoning is supplied by the Third Theory of Comminution," which states that the work necessary to break a particle of diameter F varies as F. Since work equals force times distance, and the distance of deformation before breaka4e varies as F it follolvs that the breaking force should vary as F½ These relationships are expressed in Table I, with a 1-in. ball representing one unit of force and breaking a 1-mm particle. This establishes theoretically the general rule used in Eq. 1 that the ball size should vary as the square root of the particle size to be broken. Ball Size and Work Index: The work input W required per ton" varies as the work index Wi, and the

Jan 1, 1959