Search Documents

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By James A. Berberick

Research methods to develop an economic model for the determination of regional mineral advantage are discussed. An industrial complex conceptual framework is used to study potential mineral resource outputs of Kansas. A procedure for making a comparative cost analysis of potential outputs for a Kansas-based industrial complex is outlined and illustrated. Methods for estimating aggregate demand and for developing an input-output matrix for a hypothetical limestone complex are explained. The input-output matrix is expressed in physical units. A computer algorithm for converting physical production data and input cost data into total cost per unit of output information is briefly explained and flowcharted. Limitations and usefulness of this procedure in determining regional advantages are surveyed.

Jan 1, 1969

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By Z Chang, S A. Mrozek

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Antamina, Peru is the largest Cu-Zn skarn deposit in the world. Skarn mineralisation is focused around a multiphase Miocene intrusive complex comprising at least eight distinct phases identified by cross-cutting relationships, including truncated veins, xenoliths and chilled margins. Skarn alteration and mineralisation, as observed in drill core, remain open at depths exceeding 2.2 vertical kilometres.Porphyry intrusions occur as four major phases with subphases (from oldest to youngest): P1 (a, b), P2 (a, b), P3 (a, b) and two dykes of uncertain timing named Oscarina-1 and Oscarina-2. P1a is a hornblende-biotite quartz diorite porphyry with pervasive K-alteration, local endoskarn and 30–40 per cent sheeted quartz veins, all of which obscure original igneous textures. P1b dacite porphyry is a minor unit with <10 per cent phenocrysts and <3 per cent quartz veins. P1b cuts P1a; P2 dykes cut both units. P2a porphyritic biotite quartz monzonite contains K-feldspar megacrysts up to 4 cm long, local K-alteration and 2–80 per cent quartz stockwork veins. P2b biotite monzonite porphyry contains approximately 50 per cent phenocrysts and typically <10 per cent quartz veins. P3a (brown groundmass porphyry) and P3b (coarse phenocryst porphyry) are minor in volume and extent, and both cut P2 bodies. Oscarina dykes comprise two separate but parallel bodies. Oscarina-1 is a feldspar-phyric rhyolite porphyry, while Oscarina-2 is an intensely chloritised andesite porphyry. Oscarina-1 has a U-Pb (laser ablation inductively coupled mass spectrometry (LA-ICP-MS)) age of 10.1 ± 0.1 Ma, whereas P2 U-Pb zircon ages (LA-ICP-MS) range from 10.0 ± 0.2 Ma to 9.9 ± 0.3 Ma.All the intrusive phases contain quartz veins, with P1a and P2a having the most intensive K-alteration and most abundant quartz veins ± endoskarns. Each phase may have contributed to mineralisation at the right depths and within favourable wall rocks (ie marble) during uplift of the Antamina structural block. Therefore, a model of multiple intrusions during continuous uplift explains the vertically extensive (>2.2 km) skarn and mineralisation at Antamina.CITATION:Mrozek, S A, Chang, Z and Meinert, L D, 2015. A model for the intrusive sequence and Cu-Zn skarn formation at the Antamina deposit, Peru , in Proceedings PACRIM 2015 Congress, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By Adam Powell, David Dussault

"Electric Field-Enhanced Smelting and Refining is a process for driving the reaction between carbon in hot metal and iron oxide in slag, for example, in a steelmaking reactor. This process involves inserting electrodes into the slag and metal phases, such that the overall reaction FeO + C -> Fe + CO is separated into two half-cell reactions: Fe2+ + 2e· -> Fe at the cathode in the slag, and C + O 2 • -> CO + 2e· at the anodic slag-metal interface. Without the electrodes, the reaction is very slow, but with electrodes, the additional surface area available to the ferrous ions for reduction accelerates the reaction even without any applied bias. When a bias is applied to the electrodes, the electric field across the slag further accelerates the overall reaction.With or without applied bias, the process is first-order in the ferrous ion concentration, and limited by ferrous ion transport to the cathode. To complicate matters, as the liquid iron is reduced at the cathode, the Mullins-Sekerka instability leads to formation of dendrite-like liquid iron fingers which grow into the slag. Because of this, the design of the cathode can have a significant effect on the overall process kinetics, and understanding of the dynamics of these fingers and of their effect on mass transfer is necessary for the intelligent design of the overall process and the cathode in particular.Toward this end, a detailed mesoscopic two-phase slag-metal model is presented here which describes multi component diffusion in the slag and fluid flow in both phases in the vicinity of the cathode. Diffusion in the slag is driven by chemical and electrical potentials. The phase boundary is modeled as a diffuse interface using a phase field approach. Because this electrochemical reaction occurs at high-temperature, the kinetics of charge transfer and adsorption through the double layer are fast relative to transport, permitting the use of simple linear reaction kinetics. This also eliminates the need to discretize the double layer, with the result that charge neutrality may be assumed everywhere in the domain. Introducing electric field dependence of the gradient potential and well height coefficients in the free energy function allows the model to capture electrocapillarity at the interface."

Jan 1, 2001

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By Scott Scovira, Ruilin Yang

This paper presents a non-waveform blast vibration model for the near-fi eld. The model uses the concept of a dominant charge augmented by other contributing charges estimated using a scaled time window. The model accounts for the effect of broken ground created by earlier fi ring holes, amplitude attenuation, effects of signal broadening with travel distance from frequency attenuation, as well as asynchronous propagation of different wave types due to the wave velocity difference, the delay time effect, and non-linear superposition of near-fi eld vibration. The model uses an effective distance defi ned from the broken ground screening, and determines a dominant charge contributing to the PPV at a monitoring station. Then the model uses a time window for each individual charge to determine if it contributes to the PPV. The time window has a variable width to model the effects of the signal broadening with travel distance. For modeling the signal broadening, a generalized rock quality factor Qd is proposed. The time window includes a weighting function that diminishes the contribution for charges fi ring further from the dominant charge and this accounts for contribution arising from the timing difference between a contributing charge and the dominant charge. The model uses a non-linear charge weight superposition technique that scales the charge weights within the time window to the same distance of the dominant charge and superimposes the scaled charge weight. The case study demonstrates that the model provides useful predictions for near-fi eld blast vibrations.

Jan 1, 2008

By Aydin Shaterpour Mamaghani, Cemal Balci, Nuh Bilgin, Mucahit Namli, Hanifi Copur

"It is expected that more than 10 Billion USD will be spent in Istanbul in coming years on tunnel boring especially with EPB-TBMs. However, the geology of Istanbul is very complex. Geologic formations changing from Paleozoic to Cenozoic ages cause tremendous problems due to frequently changed rock formations and andesite and diabase dykes. This paper summarizes a universal model to predict the performance of EPB-TBMs which is created upon the data base collected from several projects. The model first is based on predicting field specific energy and power consumed of TBMs using geo-mechanical properties of the excavated material and TBM diameter. Later net production rate is calculated using field specific energy and power consumed by TBM. A methodology to predict machine utilization factor permits to calculate daily advance rates. The validity of the model is tested using the data obtained from two recent metro tunnel projects. 1. INTRODUCTION It is expected that in a near future a total length of 400 km will be excavated in Istanbul in a complex geology. Selecting proper tunneling equipment, organizing an effective operational management with the right tunneling crew will be a major concern for an efficient scheduling of the future projects necessitating to create a model to estimate daily advance rates. Several TBM performance prediction models with few on the prediction of machine utilization time were realized in the past. However, there is quite limited number of research studies on predicting the performance of EPB TBMs. Specially predicting daily advance rates in complex geology, in mixed face, in fractured rocks, in transition zones etc. are in big concern (Namli et al. 2013, 2014). The first experiences in Istanbul with a gripper type TBM was a nightmare, roof collapses caused big delays in tunnel excavation (Bilgin 1993). A typical example to EPB-TBM was Kadikoy-Kozyatagi tunnel, changing TBM from opened mode to closed mode with few modifications on the cutterhead resulted a tremendous increase in the daily advance rates (Bilgin et al. 2009). The data collected from several tunnelling projects served a basis to create a model to predict daily advance rates of EPB TBMs. Within the frame of a research program the validity of the model was tested in Uskudar-Umraniye–Cekmekoy-Sancaktepe metro project and very recently in Mecidiyekoy-Mahmutbey project."

Jan 1, 2016

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool, HeapSim. Some of the sub-processes that are modelled include mineral kinetics, particle size effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation. The interplay of these various sub-processes is illustrated in the paper.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. The first is focussed on chalcocite heap bioleaching, which shows that by nature of the reaction the process is strongly dependent on the initial supply of acid to the mineral site. In heaps this acid supply can be severely limited by the rate of diffusion from channels of flowing solution into stagnant zones of the heap, whereas in narrow-bore laboratory columns this effect is not observed."

Jan 1, 2003

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool. Some of the features include mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. In each case the model has proved as an invaluable tool either for the improvement of existing heap leach practice or for the development and assessment of novel applications."

Jan 1, 2003

By Howard Hughes

IN drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, . Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,000 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 3, 1915

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By R. F. Favreau, L. C. Lang

"In modern blasting technology blasts are designed and analysed on an energy-mass-time relationship. The energy of the explosive is derived by computer analysis and the work potential of the available energy is expressed in numerical values. The mass involved in the blast is determined by the geometry of the blast and by the rock density. Time is also a relevant parameter, because time is required to complete the three basic stages of the breakage process.For successful application of the blasting parameters the basic mechanism of the breakage process must be understood.The physical-mechanical properties of the rock, local structural geology and the thermodynamic properties of the explosives can be brought together to create a computer model of a blast with which it is possible to predict separately the results of each parameter and to express the predicted degree of change in any parameter by actual numbers.A long-range project has started to create a ""bank"" of rock properties for as many Canadian and foreign mines as possible. A computer model has been successfully applied to predicting the effect of varying the ratio of spacing to burden at constant rock volume and significantly improved results are achieved, as the S/B ratio is increased up to about 2 to 2.5.High-speed photography has been applied to determine the time that has elapsed between zero time and the beginning of movement of the mass. The results assist in determining minimum and optimum delay time required for multiple-row blasting.The approach as described in the paper is now well proven and is clearly superior to previous methods based on powder factors and human assessment."

Jan 1, 1972

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010