Search Documents

By Saba Gharedash

In this study the results of a series of numerical simulations which are conducted for one of the tunnels of the Mashhad metro line 2 project are presented to evaluate the role of tunnel face support pressure and soil strength parameters on deformation of tunnel lining and face deformation. To achieve this goal, comparative numerical simulations of a mechanized tunnel advance in soft non- homogeneous soil on top of the ground water table and beneath the building are conducted and sensitivity analysis is performed. Development of a step by step tunnel construction process is modeled using a three dimensional finite difference model (FLAC3D) taking into account all the relevant components of shield tunneling. In order to understand the mechanism of the effects of a variety of support pressures on face deformation and lining stresses, numerical simulations are conducted. It is found that the use of different face supports causes a considerable influence on the forces of tunnel lining. In addition, it is revealed that building weight help to change the stress paths and the stress distributions in the tunnel lining.

Aug 1, 2013

By M. A. Sobhi, L. Li

With the continuous reduction of mineral resources at shallow depth, more and more mines have to go deeper beneath the earth's surface to reach the ore zones. This increase in mine depth leads to a natural stress increase, which also raises the stresses around mine openings. This may result in ground instability, including the risk of rock bursts or exceedingly large opening closure. Stope backfilling is a well known solution to improve the ground stability condition. It also has the advantage of reducing the mining wastes disposed on surface, thus helping to reduce the environment impact from the industry. However, most available solutions for backfill design were developed for an isolated stope without taking into account the influence of mine depth, except for a few numerical analyses performed recently by Falaknaz and coworkers for the case of multiple backfilled stopes laying in the same level. In this paper, a numerical study is carried out to evaluate the stresses in backfilled stopes overlying a sill mat. The mine depth and the excavation of the underlying stope below the sill mat are both taken into consideration. Compared to the case of a single isolated backfilled stope, the obtained numerical results show that the stress magnitudes in the overlying backfill are considerably increased due to the excavation of the underlying stope. In general, the stresses increase with mine depth and backfill stiffness, but decrease with an increase in the surrounding rock mass stiffness. These results indicate that the barricade and sill mat backfill design should take into account the excavation of the underlying stope and the mine depth.

Jan 1, 2015

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By M. Ghamgosar, Erarslan N.

Rock cutting includes many unknown parameters which result in different consequences of the different cutting conditions. However, based on the current suggested models for rock cutting, there are some critical parameters that control the fracture initiation and propagation in the rock domain. In general, there are two major cutting tools are used in rock cutting: drag bits and indenters. Different mechanical attacks of cutters result in different fracture models. For example drag bits break the rock parallel to the rock surface, which is called ‘undercutting’ while indenters cut rocks by pressing normal to the rock surface. Both tools cause rock failure by inducing tensile cracks in the rock. However, drag bits induce more tensile cracks compared with the indenters. The full benefits of improvement in rock cutting efficiency will arise from a clear understanding of rock fracture mechanics principles. Therefore, fracture mechanics principles will be applied to the rock cutting as the rock fragmentation process is based on the rock fracturing. The Oscillating Disc Cutting (ODC) has more advantages than drag bits and disc cutters. The forces transmitted back through the cutting head are much lower with ODC. Although ODC attacks rock in much the same way as drag bits, a combination of the oscillating action of the cutter and the undercutting mode produces the lower cutting forces and causes rock fatigue. Fatigue phenomenon in rock has advantages for the rock breaking by applying less effort and energy due to the cyclic loading. The aim of this study is using the Extended Finite Elements Analyses (XEFM) numerical modelling for simulating the ODC cutting with different cyclic loading conditions. An accurate prediction of numerical investigation requires detail laboratory experiments. A series of laboratory tests were performed to obtain the fracture toughness values of our Monsonite rock samples under various cyclic amplitude and frequency values. The numerical results showed different types fatigue damage mechanisms due to the various cyclic loading conditions. Thus, modelling and understanding the crack propagation behaviour depending on different amplitude and frequencies are believed very important for the dynamic rock cutting researches and rock cutting machine manufacturers.

Jan 1, 2015

By F. Mackay, S. A. B. da Fontoura

"The theoretical solution for a viscoelastic well was presented by Gnirk and Johnson in 1964. From this an exercise was executed to validate the numerical simulation of a cemented salt well. The exercise comprised the geomechanical behavior through time of a cemented salt well, this was achieved using a finite element commercial software. This simulation showed the accuracy of the theoretical solution for viscoelastic materials such as salt rock. The theoretical solution presented elastic and viscoelastic analytic equations for the tangential and radial stresses. The equations for the elastic material (casing and cement) and for the viscoelastic material (salt rock) are presented here: Where equations 1a & 1b are the radial and tangential stresses of the elastic material; equations 2a & 2b are the radial and tangential stresses of the viscoelastic material; and a, r and b are the geometrical parameters explained in Figure 1. These equations are function of Pb, a stress time dependent factor that comes from the Burgers model of viscoelasticity. This is well explained in Gnirk and Johnson (1964) and for the sake of simplicity is not disclosed here. Po is the stress at section A-A’ dependent of the depth h."

Jan 1, 2015

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By R. C. FLEMING

G OLD MINING is enjoying a real revival in the West, and a considerable portion of the production is coming from small properties. The large mining companies of the world get most of the publicity, but in the last year the small gold property has often proved a more attractive field for the mining engineer looking for something to do. Old mines have been re- opened, prospects have been more closely examined, and many properties that were out of the running with the high commodity and labor costs of two or three years ago, have recently been making money for their operators. An interesting phase of this activity is the operation of so-called one-man mines. The west is dotted with these small properties, without the resources or reserves to warrant large-scale operation, but which return a living and often something over to one or two men who under- stand mining and simple methods of treatment.

Jan 1, 1932

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

A parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading on the strength and yield pattern of a stone pillar using two simplified geometry types. In type-1 the side walls of the pillars were assumed to be perpendicular to the roof and the floor, while in type-2 the side walls were assumed to be vertical. These two geometries are frequently used to simplify/model the creation of pillars in dipping mines. Results from the numerical modeling indicate that dipping pillars have reduced strength compared to horizontal pillars, and they are at an elevated risk of failure. Also, an asymmetric failure propagation pattern could be obtained depending on the interaction between the pillar width/height (W/H) ratio, seam dip, in situ stresses and pillar geometry.

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By D. -H. Park, G. -j. Kim, Y. -J. Park, C. -S. Hong, S. -Y. Choo

To evaluate the quantitative tunnel behavior influenced by characteristics of discontinuity, this pa-per executes the parametric study using 2 and 3-dimensional DEM analysis. First of all, this study finds that displacement and the stress of shortcrete are proportioned to frequency of joint and rockbolt axial force is adversely proportioned too. Secondly, it is found that the most sensitive in-put parameter used in Barton-Bandis(BB) model is residual friction angle. Finally, when joint sets are encountered at tunnel excavation face, to identify the most critical joint orientation is very crucial for a stability of tunnel. La thèse a pour but d’étudier les influences sur la stabilité du tunnel, au niveau du réseau de la discontinuité et de la valeur de sa nature aquis par le projet récemment exécuté en vue de mener à l’analyse quantitative de cette stabilité, en appliquant chaque différent paramètre comme la fréquence de diaclase, la constante de résistance des modèles de Barton-Bandis(BB) ainsi que la relation entre le sens d’excavation du tunnel et le réseau de diaclase en 3 dimensions. En fait, cette étude nous a montré que la fréquence de diaclase s’accroît proportionnellement au déplacement et à la contrainte du béton projeté. L’angle de friction résiduel s’est montré le plus sensible à la stabilité du tunnel parmi les modèles de BB. Aussi à travers l’analyse à 3 dimensions, il s’est vérifié que si l’angle de pente du groupe de diaclase est horizontal entre l’axe du tunnel et la direction, il donne une influence importante sur le comportement du tunnel. En particulier, l’influence était la plus importante sur un fond rocheux dont la diaclase horizontale est grande. Um das quantitative Verhalten des Tunnels zu bewerten, eroertert dieses Papier eine parametrische Studie mit Hilfe der DEM Analyse. Auch wird hier eine zweidimensionale Analyse von Ver-bindungen verschiedener Frequenzen in der Gesteinsmasse, eine sensitive Analyse von allen der im Barton-Bandis-Modell (BB) genutzten Parameter und eine Dreidimensional-Analyse mit ver-schiedenen dreidimensionalen geometrischen Veteilungen von Verbindungen ausgefuehrt. Erstens: Die Studie findet heraus, dass Vedraengung und Druck im Shortcrete proportional zur Frequenz von Verbindungen und Axialkraft der Steinbolzen antiproportinal ist. Zweitens: Es wird herausge-funden, dass die am meisten Sensitiven der im BB-Modell angewendeten Eingaben die am Ende uebriggebliebenen Reibungswinkel sind. Und schliesslich wird herausgefunden, dass wenn Ver-bindungsteile an der Tunnelaushoelungsoberflaeche ausgemacht werden, fuer die Tunnelstabiltaet die Identifikation der meist kritischen Verbindungsorientierung sehr bedeutungsvoll.

Jan 1, 2003

By N. Naudé, J. de Villiers, C. P. Bergmann

It is proposed that the physical and chemical composition of individual mineral particles are an appropriate basis from which to model the performance of minerals processing equipment. Such a particle-based approach enables modelling across disciplines such as comminution, classification and flotation and automatically generates the traditional mass and chemistry balances. The general approach followed is to generate full grade-recovery curves for a separator by sampling product and tailings at varying mass yields. AutoSEM characterisation of each sample provides particle data that is used to reconcile mineral deportment and liberation to the measured size and assay data. In this way, partition surfaces can be generated and modelled. In this paper, an empirical model for the performance of a gravity spiral concentrator treating fine chromite ore is proposed. The model is based on the combination of two partition surfaces and is able to accommodate both forward and reverse gravity concentration effects per size fraction. The results show that this approach is well suited to represent spiral performance for the cases evaluated. The effect of two feed particle size distributions on the performance of the Multotec SC21 and SC25 spirals is demonstrated. Simulations are run in an Excel environment, linked to Python-enabled routines for enhanced data management and calculation speed. Keywords: Spiral concentrator, gravity separation, particle-based modelling

Jan 1, 2020

By M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 1998

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing that has been used in other contexts. The International Seabed Authority or another entity will need to coordinate and promote this licensing regime through governance of intellectual property derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines has developed a PC based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1994

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920