Search Documents

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By G. Aggistalis, N. Kazilis, C. Rawlings, N. Rachaniotis, S. Raptopoulos, M. Knights, R. Game

The Egnatia Odos (Odos meaning road) is one of Greece’s largest ever highway construction projects and one of Europe’s most important. The Highway will assist in the connection of the Greek Ionian/Adriatic Coast with Turkey and the Black Sea reviving an historic Roman alignment “Via Egnatia” connecting Rome to Constantinople (now Istanbul). There are 74 twin tunnels (60 bored and 14 cut-and-cover) with lengths ranging from 160 m (175 yd) to 4,600 m (5,031 yd) and 100 m (109 yd) to 270 m (295 yd),respectively. The complex geology and resulting physical geography have had a major influence on both the design and construction of these tunnels. This paper describes the management, design and construction challenges of these numerous tunnels.

Jan 1, 2005

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By R L. Brathwaite, S E. Belliss

Linear and semi-circular features were mapped in the volcanic terrain of the southernCoromandel Peninsula, North Island, using JERS-1 synthetic aperture radar (SAR), Landsat-4 Thematic Mapper, and SPOT-2 multispectral satellite data, digital elevation models, and aeromagnetic data. The mapped features typically correspond to recognised physiographic features and are thus a useful aid to mapping the structural trends in the region. Major linear features exhibit a strong N-S to NNE-SSW alignment, and lesser NW-SE and NE-SW trends. All these are superimposed on pervasive, closely spaced, NNE-SSW and NNW-SSE lineaments present over most of the hilly parts of the map area. There are few major E-W aligned features. Some alignment trends correspond to strike directions of veins in the epithermal gold-silver deposits of the region, but none of the known mineralised structures were visible on the remote sensing data.   The volcanic rocks are Late Cenozoic in age and include a variety of rock types: andesite and dacite flows, domes and tuff breccias, rhyolite domes, tuffs and tephra, lacustrine siltstones, and ignimbrites. Mapping of different textures in the SAR image failed to provide additional information on rock types to that derived from the Landsat and SPOT images. A simple discrimination of rock units based on radar texture is apparently prevented by the complex volcanic geology, superimposed hydrothermal alteration, and long period of erosion.

Jan 1, 1994

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

Traditionally, the gravity cleaning of coal has been evaluated in pilot plant tests. Attention is now turning to the development of empirical models of gravity cleaning equipment that can be used for the design and evaluation of circuits. This paper presents some preliminary information for spirals and water-only cyclones treating fine coals. Also discussed is how such information gives a better understanding of the operating and performance characteristics of this equipment, how realistic comparisons can be made between different types of equipment, and how small mobile plants could be designed for treating the fine coals 'stockpiled' at many NZ mines.

Jan 1, 1985

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

By T. J. Yeomans

"The Kidd Creek metallurgical site is situated twenty-six kilometres east of Timmins, Ontario. The site consists of a 4.5 niillion tonne per year concentrator, a 127,000 tonne per year electrolytic zinc plant and a 79,000 tonne per year copper smelter/refinery complex.The concentrator commenced operations in 1966 and was expanded to its present capacity in 1978. The zinc plant commenced operations in 1972, and the copper smelter/refinery in 1983.The concentrator tailings, and both liquid and solid waste products from the other plants are disposed of within a 1215 hectare tailings disposal area. Here, a method known as centraljzecl thickened discharge is used to form a stable cone-shaped hill. A low permanent perimeter dyke structure encloses the cone and directs cone run-off and thickener overflow to a treatment pond. After treatment with lime slurry, this neutralized effluent is recycled to the metsite and also discharged into the Porcupine River system.The tailings system has been in operation in its present form since 1972, upon completion of dykes and a 110 metre thickener unit. Underflow densities were continuously increased until thickener overloading became a serious problem. This necessitated the construction of a second 110 metre thickener, which was completed in 1983. Target densities have been achieved without difficulty since then.This paper discusses the operation of the tailings system, reviews past performance, and outlines future operations."

Jan 1, 1986

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968