Search Documents

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By S. F. Mauser

This report describes the study of factors which affect medium voltage (661 - 1000 volts) trailing cable splices used in underground coal mines. Improvements in quality, dependability, and design of splice kits and shop splices are presented in the study results and recommended guidelines and regulations. Recommended research programs are included which describe approaches for development of the recommended guidelines and regulations for medium voltage trailing cable splices. The basis for the conclusions and recommendations presented in this report is included in three appendices which describe a survey, splice examination, and general requirements development prepared during the progress of this study.

Jan 1, 1977

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By M. C. Malamphy

The report of work accomplished on the United States Bureau of Mines' bauxite project in Pulaski and Saline Counties, Ark., is presented in this volume and in a series of Reports of Investigations immediately following this volume. This first volume covers the project as a whole, whereas the subsequent volumes contain maps of local areas and deposits developed, together with logs of the drill holes and descriptions of the separate deposits. The Arkansas bauxite project was initiated in December 1941 and continued for 4 years. The first 5 months were spent in studying the problems presented and in geophysical exploration, Core drilling began in May 1942 and ended in May 1945. The project was one of the larger and more important of those undertaken by the Bureau of Mines for the purpose of developing domestic sources of supply of critical and strategic minerals necessary for National defense and for the successful waging of modern mechanized warfare. Some of the results of the Bureau's bauxite exploratory work have been made available to the public through the medium of press releases, transactions of technical societies, and government publications. More information has been supplied to government agencies upon request and to land owners and mine operators of the deposits concerned in the form of maps showing locations of all holes drilled on the property and logs with chemical analyses of' all cores recovered. In October 1946, the factual data were made avail-able to .the public in manuscript form in an-"open file" at the office of the State geologist, R. B. Foxhall, Little Rock, Ark., and at the office of the. Bureau of Mines in Washington. For the purpose of providing a background for the presentation of the factual data obtained, the history of bauxite is reviewed briefly. Information relative to past production and reserves of bauxite in Arkansas also is given. A resume of the development of the industry in Arkansas, the exploration and mining methods employed, the various uses to which the bauxite is put, and a brief outline of the geology of bauxite in Arkansas complete the -background.

Jan 1, 1948

By B. McLaughlin

Agnico-Eagle started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240 m deep shaft. Exploration success led to the installation of a hoisting plant capable of extracting 4500 t of ore and 1800 t of waste per day from a depth of 2210 m. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

Jan 1, 2004

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By A. H. WHITE, PERRY BARKER

In a consideration of the various means whereby more economical and more efficient use may be made of the fuels in the United States, the possibility of obtaining for the production of illuminating gas other and cheaper fuels than the Pennsylvania coals demands attention. For the Government, as well as for private corporations and the householder, there can be no more economical and efficient way of using some coals than through the medium of illuminating gas. In the stove, gas reduces the labor cost of heat production and lessens the drudgery of the kitchen; burned in the Welsbach mantle, it is an excellent and cheap illuminant. In addition, the coke that remains after the gas has been recovered furnishes a smokeless fuel that has about the same heating value as anthracite. Hence any investigations that will indicate how local coals through proper treatment may be substituted for the higher priced and rapidly vanishing Pennsylvania gas coals will bring about lower prices for both gas and coke and will also aid to conserve for use in metallurgical processes the coking coals of Pennsylvania and of ot,her States. The annual drain on the gas-coal resources of this country and the importance of the gas and coke industries are indicated by the fact that 8,390,129 tons of coal were carbonized in retorts in the United States in 1909. The resulting salable products from by-product ovens were 15,791,220,000 cubic feet of coal gas, 6,254,644 tons of coke, and 60,126,000 gallons of tar. The total value of all by-products was about $28,508,637.

Jan 1, 1911

The Bibliographic Data Base is the result of a literature search con-ducted as one task of the technology assessment of current and advanced logging techniques, sponsored by the United States Bureau of Mines. After compilation, the bibliography was converted to an automated form for ease of utilization, and to allow for maintaining and updating the data base. The data base covers articles, symposia, books, patents, corporate and government reports, and other literature concerned with some aspect of borehole logging from January 1969 through December 1975. Periodic up-dating will be necessary to keep the data base contents in step with developments in the rapidly advancing field of application of borehole logging to mining. Many bibliographic indexes were scanned for entries relating to the subject of interest, and those entries which were included in our data base contain a reference to the bibliographic index in which they were listed (see Section 2.4.7). With the aid of these indexes, a vast number of publications, including foreign reports and publications, have been scanned for works relevant to borehole logging technology.

Jan 1, 1976

By Henry Kreisinger, John Blizard, B. J. CROSS, C. E. Augustine

This report gives the results of 26 tests of a four-pass Edgemoor boiler fired with powdered coal at the Lakeside station of the Milwaukee Electric Railway & Light Co. The tests were made by the fuel section of the Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation and the operating department of the Milwaukee Electric Railway & Light Co. The object of the tests was to determine the thermal efficiencies and capacities obtainable by burning powdered coal under large central-station boilers, and the possibility of operating such boilers continuously at high efficiency and capacity without destructive effect on the furnaces and without difficulties in refuse removal. In any system for burning pulverized coal the furnace is the most important part because, to justify the cost of pulverizing, the powdered coal must be burned with higher efficiency than coal fired with mechanical stokers. In other words, it is the furnace that by giving higher thermal efficiency must pay for the installation, maintenance, and operation of the pulverizing equipment. No matter how simple the apparatus for the preparation of pulverized coal may be, or how simple the pulverizing process, unless the furnace is so designed that it can be operated continuously with high thermal efficiency, the whole system is a failure. For high thermal efficiency the coal must be burned almost completely with low excess air. But low excess air and complete combustion give high furnace temperature, which in turn causes erosion of the furnace lining and fusion of the ash; and removal of the fused ash is difficult. The necessity of complete combustion with low excess air thus brings with it these two important problems in the design of a furnace for burning powdered coal: 1, Prevention of erosion of the furnace lining; 2, easy removal of refuse from the furnace. For the purpose of solving these problems, the boiler tested was equipped with a furnace having hollow walls, through which about 60 per cent of the air needed for combustion passed before it entered the furnace. By passing through the hollow walls, the air cooled the furnace lining and prevented excessive erosion. A water screen was placed in the furnace about 3 feet above the bottom to keep the refuse deposited at the bottom from fusing and to make its removal easy. The design of the furnace, water screen, and burners was based on the experience gained in the previous cooperative tests1 with a smaller furnace, experimental water screen, and burners at the Oneida Street station of the Milwaukee Electric Railway & Light Co. The boiler tested had 13,057 square feet of heating surface. It was one of eight boilers fired with powdered coal, and was designated as boiler No. 8. The Lakeside station is the largest central station in the world that burns powdered coal exclusively. The coal used in the first five tests came from Illinois. The fuel in the other tests -:vas a mixture of Illinois and Pittsburgh coals.

Jan 1, 1925

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

Real-Time Integration of Mining and Metallurgical Information for Efficient Use of Energy and Water

Sep 13, 2010

By A. W. Dickerson, G. Hollier, F. A. Bartley

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research. Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May, 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Feb 24, 1997