Search Documents

By Anthony J. Konya, Calvin J. Konya

Mine sites and construction projects have faced problems with blasting a smooth back wall. This lead to safety concerns with slope stability and rock falls from the walls. Decades ago Dr. Calvin Konya began a special type of blasting called “Precision Presplitting”. This form of presplitting used relatively light loads based on the rock type being blasted. The explosive loads were estimated for each rock type and adjusted as blasting progressed. This current research project also determined a new equation for prediction of the ground vibration from one type of presplitting and compared it to vibration from production blasting.

Jan 1, 2016

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By J Dwyer, M Hill

Downer’s mining division has made an operational and financial commitment to developing engineered solutions that mitigate the risks associated with operator proximity to uncontrolled development drill boom movements, and unguarded rotating drill steels.With the potential for serious injury or fatality, these identified risks are categorised as critical. Previous attempts by the industry to engineer them out have produced limited success, with numerous incidents still occurring year on year. Ultimately, the industry (as a whole) remains reliant on procedural prevention for operator safety.Downer understood the success of such an initiative would largely depend on the effective collaboration between operational experience, technology experts and automation. With so many variables requiring consideration; such as physical operator movement, machine boom movements, variable machine positions, and underground environmental impacts – challenging traditional technologies was necessary to deliver an optimal solution.For that reason, discrete detection (similar to laser curtains or beams) was considered not fit for purpose. The use of situational mapping, using rotating lasers, however, provided the optimal solution. The lasers collect data that is then processed using a custom software application.The software application is specifically programmed for tracking and classifying objects within detection zones, using advanced algorithms and filtering. Recognition and removal of non-positive disturbances are possible without losing personnel detection capability. The detection of relevant classified objects (humans) is determined by analysis of object size, age, movement, and speed etc. When the relevant object is detected, an alarm and inhibit function is applied preventing drilling functions.Any breach of the safety zone (forward of the front jacks) will automatically disable the hydraulic boom function. This can only be reset in the cabin once the person or persons have returned past the front jacks of the development drill into the safety zone.Downer, in collaboration with partner YUMARR Automation, has successfully developed this reliable boom isolation system, and is called JumboGuard. The system has now been commissioned and installed across all Downer Mining development drill fleets, operating in Australia.CITATION:Hill, M and Dwyer, J, 2017. JumboGuard – automatic boom isolation system, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By G. Coombs, L. Meade, J. Welshimer

Industrial Minerals commodity profiles are continued from May's Annual Review issue. Diatomite G. Coombs, Manville Sales Corp. Growth in US diatomite production continued to lag in 1986. The US Bureau of Mines estimated that 580 kt (640,000 st) were produced last year. This is a 1%0 growth over 1985. The cumulative growth from the 1982 low point is 4.4%. Present production, though, is still only 90% of the high tonnage of 1979. The industry will see increased competitive activity with the start-ups of two new mines and production facilities in California and Oregon. US production has come primarily from Lompoc, CA, Bassalt, Clark Station, and Lovelock, NV, and Quincy, WA. New production, probably with capacities of 45 kt/a (50,000 stpy) each, have started near Burney, CA, and Vale, OR. Eagle Picher's new, full-line filter aid and filler plant at Celatom, Vale, OR, was dedicated in August. The plant uses diatomite from the Celatom mining district in Juntura, OR. Grefco's new filter aid and filler plant near Burney, CA, was ready in July. It produced flux calcined products through a single kiln and can handle both bag and bulk shipments. The operations are in Shata County with the plant and mine at the same site. Manville Specialties Group is moving its Filtration and Minerals Division headquarters and research staffs to Lompoc, CA. The move is intended to strengthen response and performance by locating research, marketing, and production close together. Diatomite is processed in three methods: natural, calcined, and flux calcined. The natural is dried to remove water and is particle size classified. Calcined or straight calcined products have been sintered to modify particle size or permeability. Flux calcination, or flux sintering, has a stronger influence on permeability and also benefits color. The unique structure of diatomite is used in a range of particle sizes from fine paint fillers, to coarser filter aids, to granular aggregates. Dimension stone L. Meade, Geomapping Associates Ltd. 1986 was another good year for dimension stone production. The trend toward using marble, granite, limestone, sandstone, and slate has created an increasing demand. According to US Bureau of Mines 1986 estimates, 1.1 Mt (1.2 million st) of dimension stone, with a value of $173 million, was produced by 200 companies. This is an increase from 1985, where 220 companies produced 1 Mt (1.12 million st) valued at $172 million. The increased production volume and decreased unit value is due to the competition from imports. The net import reliance in 1986 was 68% compared to 62% in 1985. The value of imports was $374 million in 1986 versus $295 million the year before. In an effort to maintain their market share, domestic finishers, particularly in the granite industry, continued to upgrade plants and machinery during 1986. In addition, offshore dollars have financed a number of fabricating facilities in North America that will finish imported rough stock. It is hoped that this increased domestic production capability will capitalize on a devalued US dollar. The trend has been for growth in stone usage and market. This trend is continuing with increased public awareness and desire for natural stone in buildings. The area of greatest market growth is expected to be in residential and interior decorative stone usage. Use of sophisticated, automated equipment has made the cost more affordable. Now lobbies, foyers, and specialty rooms are being clad in stone. Dolomite J. Welshimer, National Lime & Stone Co. About three-quarters of dolomite production is used as construction aggregates and 10% to 20% is sold or used as an industrial mineral. Total limestone and dolomite consumed for chemical and metallurgical purposes is about 136 Mt/a (150 million stpy). Sales of industrial dolomitic products were somewhat stronger in 1986 than levels recorded in the early 1980s. Some of the sales' strength, however, can be attributed to reductions in the number of active mining and processing operations. The industry will probably undergo further consolidation by the end of this decade. This will be due primarily to the continued softening in demand by the steel industry. Dolomitic limestone deposits being mined for raw materials for the steel, glass, and refractory in¬dustries are generally 54% calcium carbonate and 45% magnesium carbonate by weight. Impurities composed of silicon, aluminum, iron, sulfur, and phosphorous, represent less than 1%. The heaviest concentration of high purity, surface mineable dolomite in the US is in northwestern Ohio. Crushed and sized dolomitic limestone is a basic raw material for the iron and steel industry. It is also used as feed stone or lime kilns. Soft-burned lime is a popular raw material for BOF steel production. It is also used extensively in insulating glass fiber manufacturing. A related material, hydrated

Jan 6, 1987

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

The individual or company director who ignores his or her obligations under the Resource Management Act 1991 and under the proposed hazardous substances legislation, ignores them at their peril. Two recent cases in Canada and the United Kingdom concerning environmental offences under similar legislation illustrate the risks well.

Jan 1, 1993

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By D Craw

Formation of gold-bearing veins in Otago Schist was intimately linked to the structural evolution of the schist belt. The currently-exploited Macraes gold deposit formed in a regional scale shear zone during latemetamorphic uplift of the schist belt. Further exploration for this type of deposit will be facilitated by an increased understanding of the late-metamorphic structural evolution of the schist belt. To this end, a three-dimensional cross section through the Otago Schist has been drawn using structural data gathered at outcrops in a 20 - 40 km wide transect across central Otago. This is the first continuous detailed structural section to be drawn through the belt. The section spans an area from Textural Zone 1 metagreywacke of the Torlesse terrane in the northeast through TZ 4 schist in the central region and across the Caples-Torlesse boundary to Textural Zone 3 schist of the Caples terrane in the southwest. Two different late-metamorphic structural generations are identified in this section: the long-recognised Manorburn Generation, and a new æPoolburn GenerationÆ. The location of the Caples-Torlesse boundary has been refined on this transect by field mapping combined with whole rock geochemistry.

Jan 1, 2001

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By A. Wedepohl

Selective leaching of phases in charge chrome is used in a variety of industrial processes for the production of chromium chemicals. A mineralogical study was made of a range of local charge chrome samples, at various stages of leaching in sulphuric acid (20g/l at 90°C), using mainly a scanning electron microscope (SEM) together with an energy-dispersive spectroscopy analyzer (EDS), and X-ray diffraction techniques. It was found that the leaching behaviour of the different types of charge chrome depends largely on the nature of the secondary phases, which in turn depends upon whether the silicon content is above or below 4 per cent by mass. The leaching behaviour of high-chromium ferrite is anomalous, and it is postulated that the process is analogous to the corrosion of brass by dezincification. Keywords: charge chrome leaching, scanning electron microscope

Jan 1, 2000

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Zorigtkhuu Davaanyam, Bern Klein, Stefan Nadolski, Amit Kumar

"The High Pressure Grinding Rolls (HPGR) is a relatively new comminution technology that has been shown to be more energy efficient compared to semi-autogeneous (SAG) mills. Full and fair consideration cannot be given to HPGR-based comminution circuits in early stage projects, because presently pilot scale testing is required for assessing and sizing; pilot scale testing requires bulk samples weighing more than one tonne. A CAMIRO research program was conducted at the University of British Columbia to develop bench scale tests that would reduce the quantity of sample required to assess HPGR.Three test procedures were developed.1. The Direct Calibration Methodology calibrates piston press test results to pilot scale test results such that piston press tests can then be used to determine the energy–size reduction relationship for a range of ore types.2. The Database Calibrated Methodology, which is similar to the Direct Calibration Methodology except that it calibrates piston press tests against a database of pilot scale and piston press tests.3. The Semi-Mechanistic Methodology was developed to use piston press test results as an input for an HPGR based energy-size reduction performance model.Through utilization of these methodologies, the energy–size reduction performance of an HPGR can be predicted with minimal sample requirement. In addition, piston press testing is far more cost effective, faster, and accessible than pilot-scale HPGR testing.IntroductionOne could argue that in the future, decisions regarding selection of comminution circuits will be made primarily on the basis of energy consumption. The following facts and predictions support the argument:"

Jan 1, 2015

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961