Search Documents

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By Kennedy G. L

Experience is reporled in the operation of the pilot Lurgi carbonization plant at Morwell, afler it had been reconstructed to obtain better control of the heating of the briquettes in order to produce a strong char suitable for use as a metallurgical fuel. The theoretical Ideal Heating Cycle, which had been designed from earlier laboratory research, was closely approached in the carbonizer, and up to 97 per cent of the whole dried briquettes entering the carbonizer were recovered unbroken in the char.The strength of the char produced in the pilot plant was limited by the performance of the drier where the cracking and breakage of the briquettes was more severe. Theoretical studies have indicated that this limitation could be removed by using a hot briquette feed to the pilot plant. Experience indicates that with a hot briquette feed to the drier and with ideal heating in the carbonizer, hard char could be produced from Yallourn briquettes in continuous operation.The project has been terminated for economic reasons...

Jan 1, 1966

By M. Radwan, S. Shimada, S. Z. El-Tawil, K. A. El-Barawy, Y. Miyamoto

This study presents the results of synthesizing monolithic siliconoxynitride, Si2N2O, ceramic from a mixture composed of reclaimed silicon and natural desert sand by using the nitriding combustion synthesis method. Single-phase Si2N2O powder was prepared by the combustion of a mixture composed of silicon and pulverized sand in 3 MPa nitrogen gas. The combustion reaction completed in 2 min and the combustion temperature reached 1577°C.The as-synthesized Si2N2O powder is agglomerate of fine particles with sizes < 5 µm and has various morphologies; rod-like and irregular crystals, irregular kinking, hollow crystals and grown pseudo-hexagonal prismatic crystals. Porous Si2N2O compacts (24.5–47.1% porosities) were fabricated from the synthesized Si2N2O powder at different calcia-alumina additives (5–20 wt%) by normal sintering at 1500°C for 1 hr in N2atmosphere.They showed superior oxidation-resistance at high temperatures up to 1500°C in an oxidizing atmosphere of Ar/O2/H2O(70/20/10 kPa).Near-full dense Si2N2O compacts were also successfully fabricated from the synthesized Si2N2O powder with 5 wt% oxide additives by using the spark plasma sintering at 1600°C.DenseSi2N2O had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa.m1/2fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance.

Jan 1, 2004

By Hanry Guillén

En la Compañía Minera KOLPA, se analizó el comportamiento de sus operaciones unitarias por el período Marzo - Agosto 2016, en el cual se identificaron procesos asociados a los ciclos de perforación y voladura, bajo los términos de variabilidad NO ESTABLES NI SOSTENIBLES, los mismos que ameritaban medirlos, analizarlos, mejorarlos y controlarlos a fin de adoptar decisiones que conduzcan a operar la mina en términos de calidad y excelencia.

Sep 1, 2017

By Dan A. Brown

Outline ? Basic Concept of ACIP Piles ? Factors Affecting ACIP Pile Performance ? Applications: - Favorable Conditions - Unfavorable Conditions ? Design for Axial Loading ? Lateral Loading Considerations ? Summary & Conclusions

Jan 1, 2004

The Porgera gold deposit is an epithermal gold base-metal deposit located in the Enga Province of Papua New Guinea. Gold-silver-sphalerite-galena-pyrite mineralisation is related to stocks and dykes of dioritic composition which have intruded a series of folded marine sediments, mainly shales and siltstones, often with calcareous and carbonaceous horizons, of middle Jurassic to middle Eocene age. The most intensely mineralised zone is at Waruwari Hill, where the mineralisation occurs predominantly as massive mixed sulphide veins, and less frequently as quartz-chlorite veins and as disseminations. Mineralisation occurs in all rock types and several phases of mineralisation have been recognised.

Jan 1, 1980

The development of research activities at Risdon and the implementing of a policy of instrumentation in plant processes have, in recent years, entailed a considerable increase in research staff and created an urgent need for more space and modern laboratory facilities. The existing laboratories have been in use for 25 years and are now inadequate. New buildings have been authorized.The new buildings will comprise, firstly, a laboratory building of three floors giving a totai .floor space of approximately 11,000 sq.ft., and a pilot plant building as an annexe to the laboratory building, of approximately 4,900 sq.ft. The laboratory building will accommodate from 20 to 22 research workers, and additional plant operatives will be used for the control of processes in the pilot plant building. The new buildings are designed to provide facilities for three principal functions; the investigation and improvementof existing processes, the development of new processes up to the pilot plant stage, and the control and maintenance of instruments.LOCALITY AND ORIENTATION OF BUILDINGSThe site of the buildings is elevated ground on the eastern side of the main plant, near the main entrance and general office building. There will be no obstruction to sunshine at any time of the day, and the laboratory building will command views of wide radius from wooded hills across the River Derwentto the open sea on the south-eastern quarter.The buildings are located to provide space for future extensions. The main laboratory building faces approx...

Jan 1, 1949

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Mark A. Williams

Topography and geology greatly impact the decision of how to plan and operate a surface mine. To extract coal, five primary surface mrning methods are practiced in the United States. These include contour strip. mountamtop removal, area, modified area, and open pit mining methods. The first four approaches are commonly associated with coal mining while open pit techniques, although used in the mining of coal, are more commonly applied to the mining of hard rock, metals, and aggregates. Various sub-routines of the primary surface mining methods are likewrse applied rn the industry.

Jan 1, 1991

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By David Vergara Segura

Una empresa minera, en condiciones normales, maximiza su operación y minimiza sus pérdidas por tener operativos y equipos ligados a la producción. Por lo que es necesario la integración entre las áreas de la empresa, específicamente entre las de Mantenimiento y Logística. En este sentido, el presente texto señala la importancia del trabajo en equipo entre estas dos áreas, cuyo objetivo común es optimizar la gestión del activo que tiene un impacto significativo y directo en la producción. También se plantea bajo del esquema de una empresa minera ficticia, el desarrollo de estrategias conjuntas, y se define un modelo de gestión logístico, generador de ventaja competitiva, el cual está orientado a la optimización del uso del activo.

Sep 12, 2005

By Messenger A. J, Miles J. G

A thermal neutron irradiation technique using a mCf neutron source has been developed and applied to thp.simultaneous determination of iron and aluminium (expressed as AI2O3) in iron ore fines (-6 mm particle size) on a moving rubber conveyor belt.While the determination of iron with this technique is based on the use of a NaI(TI) detector to monitor the characteristic prompt gamma rays (7.64 MeV) emitted by thermal neutron capture reactions in the iron, the etermination of AI2O3 is based on the use of a second Nal(Tl) detector to monitor the characteristic gamma rays (1.78 MeV) emitted after thermal neutron activation of the aluminium. The second detector is located downstream from the first. Although the speed of the conveyor belt has no direct effect on the iron measurements, it must not exceed about 3 m/min if good accuracy is required for the AI2O3 measurements. Consequently an auxiliary conveyor belt is required in order to avoid interference with normal ore processing.Dynamic trials of the technique, using 1500 kg samples of ore on a 460 mm-wide rubber conveyor belt moving at 1.7 m/min, have demonstrated that the method can achieve accuracies of 0.7% Fe and 0.1% AI2O3. At the present stage of development, it is recommended that lump ore be crushed to a particle size of 6 mm before analysis.In addition to iron and AI2O3 determinations, measurements of total moisture content and bulk density are possible. The determination of Si02 is also feasible, but a separate fast neutron source (e.g., Am-Be) and a separate gamma ray detector are required.

Jan 1, 1980

By N. W. Kirshenbaum

"The Marconaflo slurry system was originally developed to reduce costs and solve technical problems in the marine transport of mineral cargoes. In the short time since its inception, it has been found to offer economies and advantages for land-based and in-plant materials handling. This efficient method of reclaiming and slurrying particulate materials at very high pulp densities can be directly utilized in a wide variety of mineral process systems. These include: storage-reclaim applications, where even cohesive, compacted materials can be reclaimed from settled storage ""on demand""; the growing number of hydrometallurgical operations wherein slurried materials are processed to extract or yield metals; certain applications associated with pyrometallurgical treatment; and as a means of augmenting the performance of conventional mineral dressing equipment, such as thickeners.INTRODUCTIONIn the continuing effort to lower costs of producing minerals and extracting metals, the field of handling and transportation often receives too little attention from those engaged in the mining and winning of ores and metals. This comment, which pertains to ferrous and non-ferrous as well as to non-metallic producers, is especially pertinent to products having relatively low value, where transport costs can be a major portion of the delivered selling price to the minerals receiver.One method which was developed recently for the purpose of reducing costs and solving technical problems in marine transport and handling of mineral cargoes is the MARCONAFLO slurry system. A notable feature of this system is its versatility; in addition to its use in marine transport1*, some of its diverse applications have included the mining and reclaiming of tailings2 and in-plant materials handling3. As the concept and fundamentals of this system have been well explained previously4,5, the mechanics of the system will not be elaborated upon here. Rather some specific ways in which MARCONAFLO can be applied to processing and extraction will be explored."

Jan 1, 1973

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By P. M. Prasad

Off-grade molybdenite concentrates, mainly derived from secondary sources as by-products of the processing of copper, uranium and tungsten ores, do not satisfy the purity requirements (percent MoS2) for the production of molybdenum bearing products. This investigation is a continuation of a successful effort to refine a low-grade molybdenite concentrate to prepare a high-grade MoS2 using a mixed acid (HF + HCl) leach procedure. Specifically, this investigation is concerned with an understanding of the separation chemistry underlying the removal of the oxide/silicate gangue and the base-metal sulfide associations present in the low-grade molybdenite by their selective dissolution in the two acids. Experiments were conducted on an off-grade concentrate containing 42.6% Mo. Results of the controlled dissolution tests indicate that both HCl and HF are suitable for the removal of the associated alumina and both work well for iron, nickel and copper. However, HF was found to be the most effective for dissolving silica/silicate and magnesia. An attempt was made to rank the leaching efficiencies of the acids used singly, sequentially or in a mixed mode. Scale-up (300 to 2,000 g) experiments were conducted to validate this approach. Excellent purification of the concentrate was possible by processing the off-grade concentrate with 10% HCl plus 15% HF at 363 K for 7.2 ks in open polypropylene reactors with internal stirring. These conditions leached practically all of the oxide and silicate gangue and 96% of the metallic impurities. Starting from the low-grade molybdenite concentrate (42.6% Mo; 71.1% MoS2) it was found feasible to obtain a refined product containing 97.8% MoS2, which is suitable for industrial use.

Jan 1, 2007