Search Documents

By Stratton-Crawley R., G. E. Agar

"A study has been done of the scale-up of laboratory bench-scale flotation to continuous plant circuit performance. It was found that the impellor speed and the air flow rate influenced the results and in this case extreme values of these operating variables were required in order to reproduce the plant rougher results in the laboratory. Despite the experimental uncertainty introduced by these extreme values, it was demonstrated that the plant performance could be predicted and experimentally reproduced with bench-scale tests.IntroductionThe mineral processing industry relies heavily on batch flotation testwork to design flowsheets, evaluate reagent s and compare various types of ore. The batch tests are generally regarded as being directly comparable within themselves, but quite often they relate poorly or not at all to continuous circuits. Obviously this dilemma generates considerable uncertainty with wide-ranging ramifications. One of the manifestations of this unfortunate situation is the commonly expressed opinion that ""it may work that way in the laboratory, but it will never work that way in the plant"".In a previous publication, a method was described whereby the results of batch bench-scale tests could be used to simulate a locked cycle flotation test series. The work to be described here is a continuation of that investigation with an extension to the simulation of an actual plant circuit. It would have been preferable to progress from laboratory batch data to a continuous pilot plant and then finally to a full-scale plant operation. However, because that possibility did not present itself, an attempt will be made to show that the performance of an existing plant circuit can be successfully simulated from batch data. The success of the procedure can be judged by the agreement among the plant results, a locked cycle test and the predicted results based on batch tests."

Jan 1, 1982

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

Valuable Components Recovery from Lead-Zinc Metallurgical Slag

Sep 13, 2010

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

An underground mine disaster is an accident of major proportions that takes a significant toll in human lives. A disaster usually disrupts the normal functioning of a mine and may result in entrapment of miners whose normal egress from the mine is cut off. A disaster often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. Explosion, fire, inundation of water or toxic gases, and collapse of a major portion of a mine are among the causes of mine disasters. Miners threatened by such an occurence must either bring the situation under control (e.g., by extinguishing a fire) or remove themselves from the danger. If control is unsuccessful, they must retreat to a place of safety. Four different activities may be involved: evacuation, escape, survival, and rescue. Evacuation is the orderly exit of people from the mine using previously identified escapeways and following a previously determined evacuation plan. Miners whose normal evacuation routes are blocked may be able to find alternative exit routes and escape by their own efforts. For those who cannot, the issue becomes survival while waiting to be rescued. The survival period may last for many days while rescue efforts are mounted from outside the mine.

Jan 1, 1981

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009