Search Documents

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

The U.S. Bureau of Mines conducted a laboratory study to determine what effect use of water-jet-assisted cutting has on frictional-ignition suppression. A single bit with a steel tip, installed on a rotating drum, repeatedly made 22-in-long cuts in a block of Berea sandstone. The drum was operated in an enclosure that contained an explosive methane-air mixture. High-pressure front-mounted water jets operating at 2,000 to 5,000 psig and low-pressure rear-mounted sprays operating at 80 psig were used; the number of ignitions that occurred with each type of spray was compared. The rear-mounted spray was more effective for preventing frictional ignitions than the front-mounted water jet.

Jan 1, 1989

By R. L. J. Phillips

"The environmental impact of the Rabbit Lake project is presented. Baseline data for fish, water, air and radon collected in 1973, 1975, 1980and 1986, are compared with post-development environmental monitoring data. Predicted environmental impacts for the developed Rabbit Lake and B-zone deposits are compared to the actual impacts. INTRODUCTIONThe environmental impact of the Rabbit Lake project has been documented through the years in several submissions to the government agencies. In 1972, the environmental baseline study for the Rabbit Lake area was completed prior to any mining activity at the Rabbit Lake pit (Fig. 1).Sampling concentrated on Hidden Bay and Pow Bay, which received the treated effluent and the waters drained from Rabbit Lake respectively.A second baseline study was done on the Collins Bay area in 1980(Fig. I) in preparation for the mining of the B-zone pit. The detail in this study was considerably greater than the detail in the previous study. Collins Bay and Harrison Peninsula were the areas sampled. The B-zone deposit is being mined at present.With the discovery of the A-zone, D-zone and Eagle Point deposits, it was decided in 1986 to begin proceedings to obtain approval from Saskatchewan's Department of the Environment, and from the Atomic Energy Control Board to develop these deposits.In preparation, a third baseline study of both the Rabbit Lake and Collins Bay areas was done in 1986 and 1987. The emphasis was to establish the baseline at the three new deposits, to quantify the actual impacts of the existing Rabbit Lake operations and to confirm the Collins Bay B-zone (1980) impact predictions. The new deposits will allow us to continue to produce uranium into the future. In January 1988, Saskatchewan approval was received.Since 1975 in the Rabbit Lake area and 1980 in the Collins Bay area, routine environmental monitoring has been done. This has resulted in one of the largest and most comprehensive environmental data bases in North America in mining. By the time the Eagle Point deposit is mined to completion, there will have been data collected for approximately 40 years.Further discussions follow which describe the impacts of the past (1972 to 1984), the present (1985 to 1987) and the future. In addition, the past and present performances and the future plans of the .waste management systems will be discussed."

Jan 1, 1989

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986

By T Grenne, R. B. Larsen

Paper presented at the conference on Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. Paper originally entitled: Processes in a newly discovered sulphide-PGE mineralisation in Norway. The Stormyrplutten mineralisation is hosted by a minor tholeiitic metagabbro of low-Ti composition intruded at a high level in the volcanic lithology. It is thought to be the subvolcanic counterpart of submarine basalts generated during an extensional episode of ensimatic arc evolution. The sulphide-PGE mineralisation occurs as stratabound pyrite, pyrrhotite and chalcopyrite disseminations with average grades of 376 ppb Pd, 313 ppb Pt, 40 ppb Au, 0.5% Cu and 0.08% Ni in a deposit 15-25 m thick. Locally the PGE content peaks at 2 ppm over 1 m. Microprobe analysis isolated 14 different platinum-group minerals, dominated by sperrylite, temagamite and borovskite and occurring as 1-20 micron compounds embedded in the main sulphide minerals or along the sulphide/silicate grain boundaries. Mantle-normalised plots reveal strong depletion in Os, Ir and Ru and enrichment in Pt, Pd, Cu and Au. The general decrease in Pd and Pt and increase in S up through the stratigraphy is similar to PGE distribution in the Darwendale subchamber of the Great Dyke in Zimbabwe, and may reflect strong fractionation of Pd and Pt in favour of the first droplets of sulphide melt; two reversals of the trend at the 4 and 12 metre levels represent replenishment with fresh magma and repetition of the cycle. In contrast to the Darwendale system, Cu and Ni also show peak concentrations in the first-formed liquids and Pt appears to have fractionated more strongly into the sulphide melt than Pd

Aug 1, 1995

"An active list of permissible explosives was published in July, 1930 as part of the United States Bureau of Mines Report of Investigations 3025, under the title of “Active List of Permissible Explosives and Blasting Devices Approved Proir to June 30, 1930”. Changes on that list were authorized in August, September, October and November, 1930, and January, March, April and June, 1931, as published in Reports of Investigations 3029, 3037, 3046, 3053, 3069, 3089, 3099, and 3123, respectively, By these changes the following explosives were added to the active permissible list:Big Red No. 9 Hercogel CBlack Diamond No. 5-A Liberty No 1Black Diamond No. 9 Liberty No. 2Burton 5, L. F. Liberty No. 3Burton 7, L. F. Liberty-Gel L.P.Duobel No. 4, L. F. Wesco Coal Powder No. 1Genigel No. 1and the permissible explosive EP-28 was transferred from the active to the in active list of permissible explosives.During June the following permissible explosives were added' to the active permissible list:Austin Red Diamond No. 9-B, L. F. BurtonAustin Red Diamond No. 9-C, L. F. Gelobel No. 4, L.F.Austin Red Diamond No. 10-A, L. F. Liberty No. 6Austin Red. Diamond No.12-A, L. F. Monobel 8 L.F.,- WR Austin Red-D-Gel"

Jul 1, 1931

By Robert F. Stewart

The oxidation of structural materials at high temperatures in gas-cooled systems can be greatly retarded by the addition of small amounts of hydrogen to the inert coolant. In experimental equipment for gasifying coal with heat transferred by helium, the oxidation of graphite and metals (molybdenum, tungsten, and certain stainless steels) by trace impurities in the coolant helium was virtually eliminated by adding 0.1 to 1.0 percent hydrogen. The reaction of hydrogen with praphite does not preclude its use to retard oxidation; at 2,400° F. only 0.2 pound of graphite per square foot per year is lost for each percent of hydrogen in the helium. The addition of hydrogen appeared to prevent the mass transfer of carbon often associated with oxidation of graphite, without causing noticeable embrittlement of stainless steels and molybdenum or other damaging effects. This method has been tested in precision gas-recycle systems and applied successfully for more than a year in a pilot-scale unit operating at 250 pounds per square inch gage and 2,400° F. It is now used routinely and can be applied to many gas-cooled systems operating at high temperatures.

Jan 1, 1962

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962

By B. W. Gandrud

This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests made by the Bureau of Mines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers The Klondyke mine, operated by the Blocton Mining Co., is about 1 mile east of West Blocton, Bibb County, Ala., near the southwestern extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/, one on the tabling of fine coal from the Thompson and Woodstock bed , and the third a washablility study of the Henry Ellen bed at Acmar6/.

Jan 1, 1939

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By Chantale Doucet

L?utilisation du remblai en pâte dans les exploitations en vrac est de plus en plus importante. Puisque la technologie existe pour fabriquer du remblai en pâte sans construire une usine coûteuse, il est maintenant possible d?élargir le domaine d?utilisation du remblai en pâte pour y inclure des gisements filoniens où le besoin annuel de remblai est moindre. Dans certains cas, l?utilisation du remblai en pâte pourrait permettre de réaliser d?importantes économies telles que la réduction de la dilution, la stabilité des ouvertures, la récupération d?une plus grande partie du minerai par la réduction de la taille des piliers et l?entreposage de moins de résidus à la surface. L?ampleur des économies est parfois difficile à chiffrer mais il est tout de même important d?en tenir compte lors de la décision d?utiliser du remblai en pâte puisque ce sont souvent ces économies qui seront déterminantes. Différentes méthodes d?extraction avec remblai en pâte appliquées aux mines filoniennes seront présentées. Des défis et les solutions reliés à l?utilisation du remblai en pâte à la Mine Doyon seront discutés.

Oct 1, 2001

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951