Search Documents

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By Zenón Quispe

El presente trabajo describe la importancia de la aplicación de técnicas de análisis de cuencas sedimentarias en la exploración de minerales del área de Cajamarca. Para ello, se determinaron los espesores originales de las Formaciones Chimú, Santa- Carhuaz, Farrat e Inca y los porcentajes de disminución de espesor y con los resultados obtenidos, se diseño y analizó el gráfico de curvas corregidas por descompactación y sin corrección por descompactación. Asímismo, se explica la posible formación de fallas no tectónicas debido a la compactación diferencial y las unidades estratígráficas que comprende el estudio.

Sep 9, 2007

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By H. Thomas, I. N. M. Nday

"*Paper written on project work carried out in partial fulfilment of BSc.Eng (Mining Engineering) degreeThe optimization of the cycle time to increase productivity at Ruashi Mining was an on-site project investigation conducted from December 2017 to January 2018. The main objective of the investigation was to determine the actual cycle time components. These comprise the queuing time, loading time, hauling time, and dumping time of ADTs (articulated dump trucks). Data was also collected on two hydraulic shovels to identify where these could be optimized. The actual cycle time obtained was compared to the theoretical cycle time to ascertain the constraints, which affect productivity. By applying Systems Thinking to the cycle time, man-made constraints of the actual cycle time were identified and recommendations to mitigate them suggested to optimize the cycle time. However, rainfall is a natural constraint that adversely affects the actual cycle time, and which cannot be mitigated.In addition, both the theoretical and actual cycle time were analysed, as well as the theoretical and actual productivity for the year 2017. Based on the findings, conclusions and recommendations were made to optimize the cycle time. IntroductionThe aim of the project was to increase Ruashi Mining’s productivity by 39%, from about 7.537 Mt of broken material mined to 12..367 Mt targeted in 2017.BackgroundRuashi Mining is a copper (main commodity), cobalt (by-product), and acid producer located in the Democratic Republic of Congo (DRC), 10 km from the city of Lubumbashi. Figure 1 shows the location of the Ruashi Mining open pit.Ruashi Mining started production in 1911 and in 2005 the mine was registered as a DRC company owned by Metorex Group Limited. In November 2013, the Chinese company Jinchua Group International Resources Co. Ltd. bought a majority stake in the business. Ruashi Mining currently produces 38 000 t of copper and 4400 t of cobalt per annum. The company has contracted NB Mining (a contract mining company) to transport its ore. To optimize the productivity of the mine, considering ore flow delivery at Ruashi Mining, the cycle time is the indicator used in this project. The cycle time components were recorded on site using a stopwatch."

Jul 1, 2019

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By X. Goso

Laboratory-scale tests were conducted at Mintek for the production of titanium powder from particulate Kroll sponge by the hydrogenation-dehydrogenation (HDH) process. The aim of this work was to produce titanium powder for powder metallurgical consolidations. The work involved the production of titanium powder at optimized conditions, which included hydrogenation in a horizontal tube furnace at 600°C for 2 hours, milling using planetary and roller mills, and dehydrogenation in a vacuumed retort fitted in a muffle furnace running at 700°C for 36 hours. The titanium powder produced in this project matched the elemental specifications of commercially available titanium powder, except for high carbon content. Nevertheless, the powder has been tested further in mechanical alloying and has been found suitable for the production of powder metallurgical compacts. Keywords Powder metallurgy, titanium components, HDH process, ball milling.

Jan 1, 2011

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By L. C. Stone, J. C. Parr, T. N. Anderson, D. Metcalf

An increase in the importance of low-grade materials as sources of gold and silver has led to the need for improved analytical methods on leach solutions, ores and various effluents, residues, and in-process streams. These are required by plant operators as guides to process control and for accounting pldrposes. Atomic absorption spectrophotometry (AAS) and AAS preceded by pre- concentration have been applied successfully to resolve many such problems. However, AAS is no panacea and imprecision or loss of accuracy can result if adequate precautions are not taken to prevent losses and eliminate interferences. The recent methods are discussed together with methods for overcoming difficulties. Comparisons with more classical analytical techniques are also given.

Jan 1, 1981

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By H. Warren Newcomen

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

May 1, 2004

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Groundwater inflow into underground constructions may cause hazardous working conditions and environmental problems. It is essential to localize and characterize potential flow paths and to estimate the amount of water leakages, so that appropriate sealing works can be performed. Estimating the amount of water ingress is a multi-phase process starting from qualitative and quantitative examination of rock mass. Due to association of uncertainty, vagueness and incompleteness with the monitored data set, particularly resulted from the in situ tests, accounting relevant approaches such Fuzzy Logic and Recurrent Neural Networks, are proposed in this research for learning acquisition, extraction of rules and prediction of behaviors. The computational set of artificial tools permits using the complex information entities or information granules (rock types, geologic structures, hydro-fracture potential) for data abstraction and derivation of knowledge from records (numerical or linguistic format). This is more a theoretical perspective than a set of methods or principles. As a theoretical perspective, this proposal encourages an approach to data that recognizes and exploits the information present in indexes at various levels of resolution or scales. In this sense, it encompasses the methods which provide flexibility and adaptability in the resolution at which knowledge or information is extracted and represented. The product of merging these tools is a 3D artificial-mapping of rock classification (Qi-system), geological conditions and Lugeon units that permits, as far as possible, to understand more and better the flow behavior."

Jan 1, 2015

By S. A. Osterberg, J. L. Breckenridge, R. S. Popielak

Multidisciplinary investigations were completed to prove the availability of water resources for the proposed San Cristóbal silver-lead-zinc mine in the arid Altiplano of Bolivia. Surface water resources are scarce, of poor quality, and unsuitable for development. Therefore, hydrogeological reconnaissance targeted alluvial aquifers for development. Follow-up resistivity, refraction, and water quality assessments were used to prioritize areas with prolific production potential. Pumping tests and regional water balance analysis indicate an alluvial aquifer can sustain the required approximately 40 000 m3 per day production for the life of the mine and predict no significant negative environmental effects on local groundwater users and the environment.

Jan 1, 2002

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001