Search Documents

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By Nick D. Rose

Outline ?Background ?History of inverse-velocity for failure prediction ?Methodolog ?Case Histories ?Three case examples of predicted slopefailure to actual date of occurrence ?One case example of mitigated slope failure using inverse-velocity to forecast failure time and schedule remedial measures ?Conclusions

May 1, 2006

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Feb 24, 1997

Iron ore in the Middleback Range area has a density and susceptibility contrast with adjacent rocks, and gravity and magnetic methods are applicable to exploration for it. The gravity method is satisfactory whether the ore mineral is hematite, magnetite, or limonite; the magnetic method is suitable for detecting ores which contain magnetite, such as some hematite ore, magnetite ore, and possible ore in the form of magnetite-bearing schists. jaspilites, and carbonate rocks.Geophysical exploration began in 1948 and is still in progress. The methods which have been used are aeromagnetic (83 per cent), ground magnetic (13 per cent), gravity (3 per cent), and others (1 per cent). Ground magnetic surveys have been made wherever aeromagnetic surveys recorded large anomalies. The gravity method is being used to investigate those parts of the area considered most favourable for ore occurrence.Qualitative and quantitative interpretation of the geophysical data has been made and the rocks causing selected anomalies tested by bores.Magnetite in the Middleback Group rocks produces the major magnetic anomalies in the area. The average magnetite content of magnetite-jaspilite, which is the commonest rock type, is 33 per cent by weight and that of magnetite-carbonate at the Iron Duke-Iron Duchess is 50 per cent. These rock types also contain hematite and the average total iron content of the former is 35 per cent and of the latter 50 per cent.INTRODUCTIONThe geology and iron ore resources of the Middleback Range area were described by Miles (1954). Since 1954, much drilling, mapping, and quarrying has been done but there is no published report of this work.The rocks which constitute the Middleback Range, Camel Hill-Cooyerdoo line, Katunga Hill-Iron Knob, and Ash Range (Fig. 1) belong to the Middleback Group of Middle Precambrian or late Archaean age. Most outcrops of the Group are jaspilites, formerly called banded hematite (or magnetite) quartzite. The high grade hematite deposits...

Jan 1, 1964

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By A B. Christie

Known epithermal deposits in the Coromandel region belong to the low-sulphidation type, represented by three subtypes: (1) andesite-hosted epithermal Au-Ag, (2) rhyolite-hosted epithermal Au-Ag, and (3) andesite-hosted polymetallic veins. Paleo-depths for a range ofdeposits are estimated using various features including: paleo-surface indicators (e.g. sinters), hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and alteration mineralogy. Paleo-depth estimates to the base of the ore zone for the rhyolite-hosted Coromandel deposits are in the range 200 to 500 m. Andesite-hosted Au-Ag deposits have more variable paleo-depths, and are deeper (up to 950 m) in those deposits with base metals at depth. The majority of Coromandel Au-Ag deposits have limited depth extents (<200 m) of economic grade mineralisation, although Waihi and Karangahake are notable exceptions with depth extents of 575 m and 700 m respectively. Limited depth extents of economic ore are a feature of epithermal systems worldwide and are commonly attributed to gold deposition from boiling fluids. Under hydrostatic conditions in epithermal/geothermal systems, boiling in an up-flowing hydrothermal fluid is controlled by the boiling point for depth (BPD) curve. From fluid inclusion studies of many low-sulphidation epithermal systems, deposition of electrum in economic concentrations appears to be confined to a temperature window of 260 to 180¦C. This means that for dilute, gas-poor fluids that follow the BPD curve, gold deposition is limited to a vertical depth zone of about 400 m, with its upper boundary at about 100 m below the ground surface. The greater depth extent at Waihi and Karangahake, can be explained by mixing of/a deep, hot (300¦C) fluid with cooler (c. 200¦C) heated ground waters. This has the effect of lowering the 260¦C isotherm by up to 300 m, thereby increasing the depth range of economic grade gold deposition within the 260 to 180¦Cwindow of electrum deposition.

Jan 1, 2000

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where 'visual pollution' is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013

By K L. Brown, J L. Mauk

Sulfide-rich scale occurs in steam and water lines at the Ohaaki geothennal field,Taupo Volcanic Zone, New Zealand. Precious metals show very high concentrations around areas ofpressure reduction (Au 15500 ppm, Ag 68800 ppm). Pyrrhotite dominates at the orifice plate due to low PH2s1PH2 conditions. Sulfide mineralogy in the scales is consistent with alteration mineralogy of the reservoir rocks. Separated steam then produces a mainly pyrite/magnetite mineralogy, with lesser chalcopyrite, where textures reflect high flow rates and high levels of supersaturation. This study outlines the effect that pressure and subsequent temperature decreases have on the mineralogy, chemistry and textures of sulfide scales.

Jan 1, 1998

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

AMONG the multifarious duties which fall to the lot of a mining engineer it is safe to say that there is none of more fundamental importance than the study of the ore-deposits on which it is thefunction of his profession to operate, inasmuch as the whole business of mining in all its complicated ramifications rests first of all on the existence of something to mine. -When the ore supplies in a mine fail, the enterprise comes to- an end, and nothing, therefore, is of more importance than a thorough understanding of the conditions under which the ore occurs, so that everything possible may be done to open up the mines well ahead of their immediate output requirements, and develop new ore reserves to take the place of that which is raised from day to day. The great aim which the mining engineer has to keep before him in his study of his ore-deposits is to obtain such a knowledge of them that he will have sound grounds for prediction as to how they will behave in parts of the mines which are well beyond the point of the pick. It is on his judgment of probabilities in this respect that mining operations are entered upon, and the more thorough his knowledge of all the factors affecting the problem, the more is the judgmentlikely to be a sound one. The test of any theory is experimental confirmation of the truth of predictions based upon it, and our aim should be to try to perfect our knowledge of the rules governing deposition of ores, so that our theories may prove themselves equal to the task of successful prediction.

Jan 1, 1909

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

In presenting this paper the author has in view a twofold purpose. In the first place, it is intended to set forth for the benefit of practical mining men some account of the principles underlying the design of tungsten carbide rock bits in the hope that a knowledge of these principles will assist in the successful application of the bits to mine and quarry drilling. Secondly, by evoking discussion, and even controversy, it is hoped that manufacturers and users of these rock bits will be encouraged to contribute to the general knowledge of a subject which to date has been rather lacking in published literature. The author well appreciates that many of the conclusions drawn in this paper are highly controversial, but if the only result is to call forth contradictory testimony from other workers in this field, at least one of his purposes will have been achieved.An attempt will first be made to set forth and examine those characteristics which go to make up an efficient rock bit, and the main factors affecting these characteristics will be discussed. In a paper of this general nature, consideration of any particular aspect must necessarily be rather brief, and there is little opportunity for detailed presentation of test procedures and data. Thus, it has been found advisable' to confine discussion of some minor points to a simple statement of fact. However, an attempt has been made to support all major conclusions by reference...

Jan 1, 1950

By L. F. Elkins

In 1946 Littlefield, Gray and Godbold published a thorough geologic description of the West Edmond Hunton Lime reservoir, located in Central Oklahoma, and discussion of its early performance.l They stressed implications of the nature of the reservoir rock on performance to be expected with production both by natural means and by pressure maintenance with gas injection. The essence of their analysis was that presence of an extensive interconnected system of fractures and solution channels constituting about 10 percent of the total reservoir void space in otherwise very low permeability reservoir rock would result in severe channeling of naturally encroaching water or injected gas through the fractures with little or no benefit to ultimate recovery of oil. Considerations were in progress to unitize the reservoir for pressure maintenance by gas injection. Some other engineers involved in the project had considerably different opinions at the time regarding continuity of fractures and regarding effects of such fractures on performance. The field was unitized Oct. 1, 1947. Subsequently, pilot gas injection tests were conducted in four areas of the field; large scale waterflooding was conducted in two parts of the field in the Bois d'Arc or Upper Hunton; and pilot waterflooding was conducted in the Chimney Hill or Lower Hunton. Full scale water-flooding is now in progress in the Chimney Hill section where it is oil productive. The primary purpose of this paper is to divine some of the secrets of this reservoir through analysis of all aspects of its performance, with the hope that it will be of help to engineers and operators in developing and operating other low permeability fractured reservoirs. In part, this considers variance of actual performance from some widely used conventional reservoir engineering assumptions. For brevity, other aspects of unit operation and its benefits to the owners are not discussed. Oil and Gas in Place For unit participation, net pay in the Bois #Arc defined by the gross SP anomaly on electric logs totalled 2,100,000 acre-ft in the 30,000-acre reservoir. Development of West Edmond predated modem logging techniques that now would be used to determine "net" or "productive" pay. In Fig. 1 this log pick is compared with detailed core analysis and core descripfion by Littlefield et a1.l for one well identified as A on the index map in Fig. 2. Not all of the gross Bois #Arc section had oil staining, but all cores with measureable intergranular permeability were stained. (The committee selection of the Bois d'Arc SP interval also includes the Frisco section as identified from cores by Littlefield.) The Bois d'Arc is oil productive throughout the entire 600-ft monoclinal accumulation from the eastern upstructure erosional pinchout to the west-side oil-water contact. (See Littlefield et al.l and McGee and Jenkins for geologic detail.)

Jan 1, 1970

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By Y. L. Su, S. Vongpaisal, H. A. Smith

"It is extremely difficult for a mine's central control room operator to control peakpower demands and to maintain normal materials handling operations at the same time. An investigation of the Falconbridge Strathcona Mine 's central control room has revealed that there are more than eight thousand possible combinations of ""situations"" that can arise. For such a circumstance, an expert system can become a very valuable tool to assist the operator in taking the most appropriate and timely action.A forward chaining expert system module has been developed for this application. The module is based on Level 5 ObjectTM software. It is graphics oriented and user-friendly. Training requirement is minimal.ForewordThis paper has arisen out of work carried out by YLS Associates and Falconbridge Limited as part of a contract between Falconbridge and the Department of Energy, Mines and Resources, Government of Canada, on the application of expert systems in mining operations.IntroductionThe electrical bill charged to large consumers by Ontario Hydro is based upon two elements: demand and energy consumption. The demand is the peak kilowatt level that the consumer has required during a monthly period. It is not uncommon for the demand portion to be as much as one third of the monthly bill. Energy consumption is the total kilowatt-hour s (kWh) consumed during the period.Ways to reduce the energy consumption part of the electrical bill involve utilizing energy-efficient equipment and operating machines in off-peak hours when a lower energy rate is charged. Maintaining the peak power below a critical level may require that simultaneous usage of major pieces of equipment be avoided. A 3000 kW skip run at an inopportune time could cost a company an extra $30,000 in that month's power cost.Potential disadvantages associated with peak power control are lost production due to work stoppage and increased operating costs due to the need to employ extra personnel. Most companies find these matters relatively easy to deal with and with incentives provided by Ontario Hydro, actively pursue this facet of energy savings (Harju , 1991)."

Jan 1, 1993