Search Documents

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By Michael J. Bertoldi

The purpose of this Bureau of Mines report is to describe the methods and establish the basic economics for dragline, shovel-truck, and scraper mining systems. An overall view of the techniques of preliminary design and the cost involved is presented. Considerations of equipment selection, emphasizing short-range evaluation of required equipment, and a long-range evaluation are considered at a constant production rate over the life of a hypothetical mine. Separate cost analyses for each system were based on 1977 equipment prices, prevailing wage rates, and associated mining costs. Specific engineering and cost breakdown for such items as access roads, transmission line installation, rail spurs, etc., are beyond the scope of this report.

Jan 1, 1977

By M. J. Farrell

The threat of global warming and its prominent position in public discussion and political debate requires all industry to take stock of its contribution to rising atmospheric concentration of greenhouse gases. For the primary metals industry, the first step must be to identify the pattern and range of emissions at each step in the production chain. Only then can the industry assess the economic consequences of the penalties on emissions that will be imposed by governments and regulators and devise cost-effective plans to avoid or mitigate such penalties. While some work has been done to estimate carbon dioxide (CO2) emissions using Life Cycle Inventory analysis, this approach is less useful than site-by-site emissions estimates. It is the level of specific emissions at each site that will ultimately deter-mine carbon taxation liabilities and participation in emissions trading schemes. Most mining companies have moved with the times to issue sustainability reports for their operations. But in the absence of any standardized reporting format, it is difficult to make useful comparisons between even the best-reported producers on a like-with-like basis. For this reason, Minecost.com modeled the use of fuels and energy used in mining, milling, shipping and metallurgical treatment to cover ?cradle-to-gate? emissions of greenhouse gases resulting from the production of the major base metals copper, zinc, lead and nickel. Greenhouse gas emissions ? overwhelmingly carbon dioxide ? are associated with the consumption of energy at every step in the production chain, from exploration through mining to the production of refined metal. Producers of primary metal employ diverse technologies to mine, mill, smelt and refine several different types of ore. Every orebody has its own special characteristics. In addition, most base metals are produced in concentrate that must be transported to smelters, with con-sequent emissions consequences.

Jan 1, 2009

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited&apos;s various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950&apos;s, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By R. Poulin, C. F. Gleeson

The Birimian rocks of the region are gold-bearing and show many similarities to those of Burkina Faso. All three greenstone belts (Goroual, Tera and Sirba) host gold-bearing quartz veins. It appears that, contrary to previous misconceptions, lateritic terrain is not an unfavourable environment for exploration geochemistry. This is demonstrated by the results for the Koma Bangou area, where soil and termite-mound geochemistry have been successfully used in the search for gold. Soil provides an effective sampling medium where it is shallower than about 2 m; there is evidence that some soil anomalies are enhanced by the presence of secondary (botryoidal) gold. In areas of thicker, allochthonous soil cover, termite-mound sampling is more effective. At Koma Bangou an identified resource of some 11 100 000 tonnes with an average gold grade of 2.44 g/t has been reported. The gold mineralisation occurs in quartz veins and stockworks aand in the wallrocks of shear and fault zones that trend N, NW and NE. The host rocks are a granodiorite-syenite porphyry and intermediate metavolcanic rocks and tuffs

Apr 1, 1996

By O. Rondon

Localized uniform conditioning is a technique developed to spatially locate selective mining unit grades that have been derived using uniform conditioning for the assessment of recoverable resources. The technique has the advantage of producing selective mining unit estimates conforming to the uniform conditioning panel-specific grade-tonnage curve while introducing spatial information at the scale of the selective mining units. This paper describes an alternative technique to localized uniform conditioning which does not explicitly require the uniform conditioning panel-specific grade-tonnage curve to localize the selective mining unit estimates. The technique can therefore be implemented in mining software where uniform conditioning is not available.

Jan 1, 2014

By C. M. Rule

Energy efficiency is currently a significant area of interest due to the Eskom power situation, which led to severe power impacts to the PGM, and indeed whole SA primary industries, in early 2008. Anglo Platinum has focused on energy efficiency for a number of years, especially in the concentrator operational area. New comminution technologies have been aggressively developed, which have shown real metallurgical efficiency gains as well as significant energy efficiency and saving potential for Anglo Platinum?s total electrical consumption as the company expands into a growing PGM demand market. This paper illustrates this programme?s activities, potential and considerable achievements to date.

Jan 1, 2009

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

Concentration of Phosphate Ore by Flotation With/Without Desliming

Sep 13, 2010

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation&apos;s computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world&apos;s leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996