Search Documents

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By R. S. Olsen

Although aluminum is easily leached from calcined clay with boiling mineral acids, the presence of fines and slimes in the leached residue has hindered the application of acid leaching processes. A feed preparation method was, therefore, devised that provided a dense, smooth-surfaced, fine-grained clay. The important factors affecting feed quality were determined to be (1) crushing the raw clay to the size desired for the leaching process, (2) moistening the crushed clay with a fine mist of water while tumbling on a rotating disk, (3) drying the misted clay, and (4) calcining the dried clay at 750° C in a fluidized bed. Clay treated by this method was leached with HCI, and its residue was washed by water displacement in 4-ft-deep beds. Bed permeabilities on the order of 47 darcys or 4.6 x 10-7 cm2 were obtained with the leached residues.

Jan 1, 1983

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985