Search Documents

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Gang Guo, Zhong Liu, Yi Zhang, Jingchun Lu

"Abstract Application of soil displacement screw pile (known as SDS pile) has been experiencing accelerated growth in Chinese deep foundation industry because of its technical advantages, environmental benefits, and cost effective as well. As bored displacement piling, SDS piles are able to perform better than non-displacement piling such as CFA plies due to changing the stress state in the soil around SDS piles during the installation. Therefore the design methods between the conventional pile type and SDS pile type have some differences. Based on the methodology research, current Chinese piling rigs, displacement augers and piling projects are introduced, and the current design approaches for SDS piles in China are also described. Moreover, the design results are verified by using full scale load tests, and a part of the research results of SDS piling system acquired in China are presented.IntroductionThe Continuous Flight Auger Pile, also known as the CFA pile, has occupied about 22% in the pile market all over the world (Van Impe, 2004; Bottiau, 2006). The CFA piles are usually used for large diameter (600mm~1200mm) pile foundations and deep excavation projects. Whereas the small size CFA piles (400mm~500mm) are mainly applied for composite foundations in China. In the past 10 years, the new technology of soil displacement screw piling has been applied worldwide (Prezzi et al., 2005). And it is also extensively used for high-rise buildings, industrial plants and railway projects in China (shown in Figure 1)."

Jan 1, 2014

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By Camier R. J, Perry G. J

Extensive deposits of brown coal exist in the Gippsland Basin, primarily in the Latrobe Valley. The total quantities of economically winnable coal in this region of Victoria and in other smaller fields are large enough to adequately assure Victoria's future electricity needs and to also provide large quantities for alternative applications, including liquefaction. As a result of the recent conflict in the Middle East attention has again been focussed on the production of synthetic fuels from coal. There have been many investigations over the years into the production of oil from Victorian brown coal. The purpose of this paper is to summarise the scope, objectives and major findings of these studies, with the emphasis on the direct hydrogenation route for converting brown coal to oil. The principal alternative processes are carboniastion and hydrotreatment of the product tar, or gasification and Fischer Tropsch synthesis of liquids from the product gas. The attractions of Victorian brown coal which have encouraged these studies include: ò the vast reserves of Victorian brown coal and the favourable conditions for low cost mining, ò the high quality of the coal (low ash, sulphur and nitrogen contents), ò the high reactivity of the coal giving high yields of product in hydrogenation to liquid fuels, ò the extensive data base available on the resource and its characteristics, and ò the availability of a skilled workforce and extensive infrastructure in the Latrobe Region to support a major resource development project. These advantages have been partially offset by: ò the high moisture content of the brown coal and the cost of drying, and ò the priority previously given to electricity generation in the allocation of the brown coal resource.

Jan 1, 1992

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

By G. G. Roy, R Shekhar

Pachuca tanks are extensively used for the cyanide leaching of gold and the carbonate leaching of uranium, processes in which oxygen mass transfer plays a very important role. Experiments were carried out to clarify the effect of design and operating parameters on oxygen mass transfer. Parameters such as the ratio of tank height to tank diameter, the ratio of draught-tube diameter to tank diameter and the tank design were found not to influence oxygen mass transfer. Results also showed that equal superficial gas velocities may be used as a criterion for scaling up oxygen mass transfer in both full-centre-column and free-air-lift Pachuca tanks with clear water. A volume-averaged, volumetric gas-liquid mass-transfer coefficient (k'av) was used to characterise oxygen mass transfer in full-centre-column tanks. The axial dispersion model was used to determine k'av. The resulting model used only tank geometry and air flow rate as inputs for the prediction of k'av in industrial-scale tanks. Predictions from the model show clearly that "local" mass-transfer coefficients, measured at one or two locations, may not adequately represent gas-liquid mass transfer in industrial tanks. It is therefore necessary to obtain an estimate of k'av

Jun 18, 1905

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010