Search Documents

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000

An Innovative Process for Comprehensive Utilisation of Clay-Vanadium Ores By adopting conventional processing technologies such as flotation, gravity concentration, and magnetic separation, it is difficult to enrich vanadium mineral effectively. At present, vanadium extraction process usually has not the mineral processing enrichment procedure, but rather uses direct hydrometallurgical process: roasting - leaching - precipitating vanadium for obtaining high quality V2O5 product. But it results in problems, for instance, high consume of auxiliary materials like acid and alkali, serious pollution and high cost of vanadium extraction. In the project study on the ore of a certain clay vanadium mineral, by adopting the test process: scrubbing raw ore with reagents added in - dispersing and segregating with reagents - grading enrichment, vanadium concentrate product with higher grade was made by virtue of reagent's selective inhibiting, and the purpose of upgrading the raw material used for vanadium extraction with hydrometallurgical process is achieved. The process technology obtained from project study features simple process structure, low equipment investment, low cost of mineral processing and pollution-free to environment. It provides high efficient and practical technology for the comprehensive utilisation of clay vanadium mineral, and has a prominent prospect for its popularisation and application.

Sep 13, 2010

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

The Department of Mineral Resources is the lead agency in mine site environment management and control inNew South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.  

Jan 1, 1995

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By Ian Misich

A research programme has been undertaken to evaluate and predict the effect of total extraction of coal by underground methods on the superimposed strata, aquifer systems and ground surface in the Collie Basin. Western Australia. The research work has integrated comprehensive field monitoring of surface and subsurface subsidence with empirical, analytical and physical modelling in an effort to develop an effective predictive tool which can be used in all mining scenarios. Early results indicate that although each method has certain limitations, this approach has enabled the researchers to develop a very good understanding of the subsidence mechanisms from the mine panel through to the surface in the weak, water saturated sediments in the Collie Basin. Given that both subsurface and surface subsidence characteristics have tied in well, greater confidence can be held for predictions made by representative models.

Jan 1, 1993

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997

By W. Pawlak, J. Janiak, C. Rodkiewicz, B. Ignasiak

"There is a general consensus that, in order to widen the utilization of Western Canadian coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques. It is postulated that the concept studied extensively over the last four years at Alberta Research Council (ARC), and based on a combination of hydraulic mining, selective agglomeration with bitumen and/ or heavy oil, pipeline transportation and oil recovery from agglomerates, offers a particularly attractive solution to the problems associated with extraction, beneficiation, transportation and utilization of Western bituminous and subbituminous coals. Results of preliminary experimental work on the feasibility of pipeline agglomeration of metallurgical coal and hydraulic transportation of agglomerates are presented and discussed in the context of conventional agglomeration techniques in stirred tanks. IntroductionAlberta is endowed with enormous reserves of low-sulphur coals which could attract considerable attention of potential customers, but the remote location of this province handicaps its competitiveness on the world market. It is known that Alberta's Cretaceous, particularly metallurgical, coals differ significantly from their Carboniferous counterparts; current R&D work on indigenous coals should continue to expand in order to encourage overseas client s to use these coals more extensively.There is a genera l consensus that, in order to widen the utilization of Western coals, a major effort must be devoted to their transportation, utilization of fines, beneficiation and mining techniques."

Jan 1, 1986

An Integrated Solid Waste Management Method for Western Macedonia, Greece

Sep 13, 2010