Search Documents

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By Lottrey A. L, Sowerby B. D, Cutmore N. G

On-line monitoring of low rank coal quality during input to a process has the potential to provide benefits through: ò anticipation of coal quality variations prior to utilisation; ò provision of a tool to help determine the influence of coal quality on process behaviour, and ò provide a direct measure of coal quality for pricing. Moisture and ash are the two most significant coal quality parameters for combustion. They determine the energy content which can be derived from the coal and the problems arising from the presence of ash in the process (eg ash fouling, corrosion, erosion, particulate emissions and ash disposal). Extensive pilot-scale testing and full-scale experience has shown that specific coal/ash constituents (eg Na2O/ash ratio, acid-soluble aluminium, silica, sulphur contents, etc) are also important for the behaviour of Latrobe Valley brown coal during combustion, ash formation, deposition and removal of ash in precipitators and furnace ash hoppers. This paper discusses the range of on-line analysis techniques which have been investigated and their application to low rank coal analysis. Preliminary results from a joint SECV/CSIRO project which aims to develop two separate advanced instrument systems are also presented. These systems are based on: ò microwave attenuation and phase shift - for direct determination of moisture content; and ò inelastic neutron scattering - to provide total hydrogen, carbon, chlorine and ash contents, with potential for calculation of moisture content, specific energy, sodium content and Na20/ash ratio using correlations.

Jan 1, 1992

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Advances in Coarse Particle Recovery - Fluidised-Bed Flotation

Sep 13, 2010

This paper describes new research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. The effort aims at increasing the overall rate of roadway development as well as providing a safer working environment for underground mine personnel. The activity is funded by the Australian Coal Association Research Program (ACARP) and forms part of a larger underground development initiative, known as the CM2010 project. The CM2010 is managed via a consortium of leading mining industry representatives through the Roadway Development Task Group (RDTG). The Task Group has identified three research areas requiring new development in order to realise the CM2010 project objectives: self-guiding (autonomous) continuous miner capability, an enhanced drilling and bolting process and improved mesh deployment. CSIRO's primary role in the CM2010 project is in the development of the autonomous continuous miner guidance capability.This paper reports on outcomes achieved at the half-way mark of a three year research and development project. It details the technical developments undertaken towards demonstration of a 'self-steering' capability to enable a continuous miner to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the continuous miner in real-time. Testing and validation of the guidance system solution has been implemented using a combination of an instrumentation-grade inertial navigation unit and radar technology. Comprehensive performance evaluations have been conducted using a scale skid-steer mobility platform known as the Phoenix. Results achieved to the present stage of the project are highly promising and suggest that an automated self-steering functionality is achievable under production conditions. This new outcome represents an important move towards implementing a step change improvement for future underground roadway development.

Dec 6, 2010

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

Advances in Optical Image Analysis and Textural Classification of Iron Ore Fines

Sep 13, 2010

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D. Richardson

Presentation Objectives ?Demonstrate the utility of 3D modelling for visualizing exploration data ?Demonstrate the target generation ability of 3D model query methods Exploration Criteria -Example Given the Geology of Sudbury What Are Our Exploration Criteria? (selected examples) ?Geometry ?Trends ?Lithology ?Proximity to Sulphides ?Length and Grade of Anomalous Mineralization ?Distance from Footwall In Addition ?Geophysical Criteria ?Economic Criteria ?Amount of Available Space ? Depth

May 1, 2006

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017