Search Documents

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

Knowledge of true block grades is obtained from a mathematical model of an orebody, simulated with sample grades normally distributed and spatially correlated according io a spherical semi-variogram model.The superiority of kriging to the polygonal method of estimation is demonstrated on this modelled deposit by comparing the true values with the kriged and polygonal estimates obtained from sampling the deposit. Finally, selection of blocks of the deposit on the basis of the estimated values, shows that if kriging is used, what is predicted is largely mined, whilst if the polygonal method is used large biases can occur depending on the position of the cut-off grade.

Jan 1, 1978

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

By J. A. McLennan

Geological uncertainty is an unavoidable characteristic of all mining projects since only limited information is available from sampling. Mine planning and development decisions with significant economic consequences are made when the geological heterogeneity is inherently uncertain. Geostatistical simulation is preferred over kriging because the methodology provides alternative property realizations that can be combined into a model of geological uncertainty. Geological uncertainty can be transferred into production uncertainty, which can help characterize the economic risk of the project. This paper presents a case study for the Pogo property, being prepared for development near Fairbanks, Alaska. The exact dimensions, grades and production predictions have been modified; however, the methodology is illustrative. The geostatistical methodology consists of (1) assembling the relevant drillhole data and establishing a suitable coordinate system, (2) calculating the target distribution, (3) creating a model of spatial correlation, (4) generating multiple realizations at a small scale and (5) linearly averaging all the realizations to the chosen selective mining unit (SMU) support size. The geostatistical model is then used to calculate production uncertainty.

May 1, 2004

By P Landeros, D Benado, J Cornejo, A Pinochet, C Caviedes

In 2005, El Teniente mine began preconditioning the primary rock mass by hydraulic fracturing (HF). The major perceived benefits of this process are a decrease in the magnitude of the expected maximum seismic event and improved cave propagation. In addition, HF has resulted in new information on the propagation pressures of each fracture. Previous studies have attempted to relate propagation pressure to minor principal stress or confining stress.Considering the spatial continuity of propagation pressure and the significant quantity of collected data since the incorporation of the HF technique, minimum requirements for geostatistical modelling have been reached, permitting robust estimates inside the representative volume with acceptable errors (Cornejo, Muñoz and Rojas, 2012; Cornejo and Landeros, 2013). These results are then used to identify zones with higher magnitudes, which are mostly related to more complex geotechnical zones (intrusive and major faults) and caving singularities, making it possible to estimate the spatial extension of these zones.Finally, these results are integrated with other geomechanics aspects to support risk analysis of the mining plan.CITATION:Cornejo, J, Landeros, P, Benado, D, Caviedes, C and Pinochet, A, 2016. Geostatistical modelling of hydraulic fracturing pressures at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Roger A. Blais, Michel David

"Matheron's geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By A Jäger, J L. Lett, J Rachocki and B Mobilio

The Newcrest Mining Limited Cadia East Panel Cave mines near Orange, New South Wales, Australia commenced production 1200 m below the surface in May 2014. Understanding the mine-wide impact caving had on excavation stability was a primary objective to ensure a safe working environment as production ramped up in the Panel Cave 1 operation and establishment activities were implemented in Panel Cave 2. The impact of cave interaction between Panel Cave 1 and Panel Cave 2 and establishing monitoring systems to assist mine planning and production as both caves joined is explained in this paper. Monitoring tools such as a microseismic system, open holes, HI-cells, extensometers, fibre optic sensing, cave markers, closure monitoring, underground observations and damage mapping were used to characterise the performance and position of the cave back. The data and observations collected were compared to predictions from numerical and empirical methods and used to calibrate the numerical models for forward prediction and to develop site empirical design tools. The results and methodology for monitoring deep high-output caves are the key discussion points in this paper.CITATION:Lett, J L, Jäger, A, Thornhill, T, Rachocki, J and Mobilio, B, 2016. Geotechnical challenges in cave monitoring – a modern approach, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 203–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005