Search Documents

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By Mike Neill, O&apos

? Bypass soft soils near the surface ? Resist uplift loads ? Resist lateral loads ? Bypass scourable soils ? Bypass liquefyable soils ? Mitigate movement of expansive or frozen soils ? "Tune" foundations for vibrating machinery

Jan 1, 1998

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By SungJe Chi

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2017

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By M. Dondelinger

This paper presents a comprehensive review of steel sheet piling including internationally manufactured hot rolled sections, their history, applications, installation and driving techniques. The discussion will cover both temporary and permanent installations; temporary piling used in construction of cofferdams with various bracing systems, deep foundation installations for buildings, bridges and tunnels, etc., and permanent piling used for highway, railroad and bridge construction as well as for riverbanks, piers, wharfs and docks, normally required for port facilities. In addition, cofferdams, as self-supporting gravity structures where interlock strength is of prime importance, will be discussed. The design and application of light, intermediate and heavy sections will be presented including heavy combined walls and information on Z-shaped, U-shaped and HZ sections and their corresponding interlocks. Emphasis is placed on new developments for design applications for deep foundations and waterfront structures within the "state of the art".

Jan 1, 2010

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010