Search Documents

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By R. F. Rolsten

VAN Arkel 1 prepared ductile tantalum by the thermal decompoiition of tantalum pentachloride on a resistively heated wire (2000° C) in an evacuated bulb maintained at 100°C. Burgers and Basart2'3 observed the formation of a mixture of tantalum carbide and free metal when a carbon deposition base was used. campbel14 suggested the thermal decomposition of the iodide if a lower decomposition tem- perature was desired. To date, the details for preparing high-purity iodide tantalum have not been disclosed. EXPERIMENTAL The tantalum to be purified was symmetrically placed around the clear quartz deposition surface centrally located within a 64 mm cylindrical Vycor bulb. The deposition vessel usually employed5 was modified6 by incorporating a reentrant fin,mer in place of the customary metal filament in the head

Jan 1, 1960

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth's crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth's surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By F. C. Langenberg, J. Chipman

Jan 1, 1959

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By Charles S. Barrett

NUMEROUS determinations1-7 of the tex-ture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Wever1 and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the roll-ing direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist.

Jan 1, 1940