Search Documents

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By G. Gabra

The kinetics of acidified thiourea leaching of pyrite concentrate was investigated at temperature ranging form 20 °C to a 60 °C. The effect of various parameters on the dissolution rates are discussed. The gold extraction was found to be zero and first orders with respect to Fe (111) and thiourea concentration, respectively. The order of the reaction with respect to sulfuric acid was found to be zero. The activation energy was determined from the Arrhenius plot as 2,039 kcal mole -1 (for a freshly prepared acidic solution containing Fe (111) as the oxidant and at 800 rpm stirring speed. This relatively low activation energy value suggests that the gold extraction is controlled by a-physical phenomenon. Under optimum conditions, more than 90% of gold has been dissolved in about 30 min. and 95% in 60 min. Attempt to recover gold from thiourea solution using active carbon is also discussed.

Jan 1, 1984

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman' equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday's constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune's compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25'C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:' where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"' system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By R. E. Gilchrist, R. F. Nielsen

When a gas is displaced by mother in a porous medium, and there is a relative immobile liquid present. there is a transition zone in which the gas composition varies from essentially that of the original gas to that of the injected gas. The change in extent of this zone with time may be governed by a mixing process in the direction of flow and by the rate of establishment of gas-liquid equilibrium, if the gases are appreciably soluble in the liquid. The relative importance of these two factors in deterri~ining the growth of the transition zone is discussed, with appropriate equations and experimental data. INTRODUCTION The various solution methods of oil recovery involve a transfer of the components of a mixture, whether within a single phase or between a liquid and gas. The similarity of a natural porous medium to systems used in separation and chromatographic processes makes it seem reasonable that certain concepts used by chemical engineers in "mass transfer" might be applicable to petroleum reservoirs. One approach, the HETP (height equivalent to a theoretical plate), involves a distance or length of time over which equilibrium might be con. sidered as established. Another approach involves direct use of a rate of mixing or rate of establishment of equilibrium. The latter approach has been preferred in relation to production problems. DISCUSSION AND PROCEDURE When a gas or liquid in a porous medium is displaced by one of different composition but miscible with it there will be set up a transition zone in which the composition varies from cssentially that of the original fluid to essentially that of the injected fluid. If the fluid being displaced is a gas, and there is a relatively immobile liquid present, the transition zone may be

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates (or sodium-free compounds) are required for certain end uses, but in general, nonsodium borates are used only where borax is not avail- able. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of about a million tons of B2O3. Leadership in supplying borates has shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates. In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, Calif., is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, Calif., the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "lo-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7- lOH2O. In addition to ship- ping all major refined borate products from Boron, the company ships semiprocessed ore concentrates to treatment plants elsewhere.

Jan 1, 1975

By Robert G. Nisle

The classic theory of pressure build-up in shut-in oil wells as developed by Horner and van Everdingen is based on two-dimensional radial symmetry in the well-reservoir system. Such symmetry does not exist in the case of a well which parfiially penetrates the producing formation. As a result of this lack of symmetry the use of the classic theory in such cases become questionable. In this paper the mathematical theory has been extended to include the case of partially penetrating wells. Numerical solutions illustrating the up-dication of the equations are presented. The effect of partial penetration on pressure build-up is shown by a comparison of synthetic pressure build-up curves derived from the numerical solution of the equation for partially penetrating wells for various degrees of penetration. It is shown that partial penetration is detectable from the characteristic shape of the pressure build-up curve and that formation productivity may be calculated from the pressure buildup data in a manner identical to that described by the classic theory. INTRO DUCTION The use of pressure build-up data on shut-in oil wells is a well-established technique for the measurement of reservoir productivity. The work of Homer' and van Everdingen' is well known. Since the publication of their pioneering work, others"' have elaborated and extended the technique. These authors have dealt exclusively with the case of wells that completely penetrate he producing formation. Two-dimensional radial symmetry is achieved, thereby, and the problem is greatly simplified. This ideal situation is seldom encountered in practice. But, in spite of this, the technique is often employed anyway. The question, therefore, arises: how much confidence can be placed in the results of such calculations when the data are taken on wells that only partially penetrate the producing formation? It is the purpose of this work to answer this question. Only the single-phase fluid case will be considered. van Everdigen' has presented a rigorous solution of the two-dimensional case, but because of mathematical complexity, this solution has not proved to be particularly useful. Horner' utilized Kelvin's point source solution in two dimensions and showed that it is a sufficiently good approximation for oil reservoir studies. The geometry of the well and the producing formation is illustrated in Fig. l. Geometrically the formation may be described as an infinite slab. The infinite slab is defined as the solid (the porous medium in this case) bounded by two parallel planes. Thus, the slab extends to very great distances in both the positive and negative directions of two of the coordinate axes, but is finite in

By H. C. H. Darley

The principal causes of unstable boreholes* have been known for many years. For example, in a paper published in 1938, Halbouty and Kaldenbachl listed nearly all the classes of troublesome shales that we know today. Much progress has been made since then, but we still have difficulty in identifying the cause of hole problems and consequently in selecting the right technique for combatting them. This subject was discussed at length by Kelly2 in a recent paper and much valuable information was provided. In the Shell Laboratory it was felt that there was a need for a better understanding of the basic mechanisms underlying the various forms of hole instability, and accordingly, a study was undertaken. This entailed reviewing the physics and chemistry of shales, developing tests for characterizing shales, and constructing a model to study borehole stability. Full simulation of underground conditions was not attempted; for example, we used reconstituted shale specimens, and often simple solutions or suspensions rather than practical drilling muds. Such procedures are necessary in order to establish mechanisms, but caution must be exercised in applying the results to the more complex conditions in the field. Part I — Compaction Swelling and Dispersion of Shales Compaction of Sediments Shales are formed by the compaction of sediments. Water is expressed as sediments are buried by subsequent layers, and the degree of compaction is proportional to the depth of burial, provided the water is able to escape easily to permeable formations. The younger sediments, when recovered at the surface, soften and disperse when mixed with water; the older shales have undergone diagenesis (alteration of the clay minerals, secondary cementation, etc.), and remain hard and unaffected by water. In this paper we shall apply the term "shale", as the drilling engineer does, to everything from clays, which are highly reactive to water, to completely lithified materials such as claystones and slates, which are completely inert. However, because these materials behave quite differently when encountered in the drilling well, it is desirable to develop a simple means of characterizing them. The feature that distinguishes the various shales is their dispersibility in water —soft clays disperse readily, harder shales disperse slowly when agitated, the lithified materials will not disperse at all unless milled. In the dispersibility test used in our study, a weighed amount of dry shale particles in the 12-to-100-mesh-size range was placed in a tube filled with distilled water and allowed to soak for 16 hours. The

Jan 1, 1970

By E. C. Stephens

The eastern Washington— Idaho clay region stretches along the northeast margin of the Columbia basin for 150 mil es. The three better known and developed clay areas are Clayton, Wash., (2 miles north of Spokane); Mica, Wash., (10 miles southeast of Spokane); and Moscow-Deary-Bovill, Latah County, Idaho (about 80 to 90 miles southeast of Spokane) see Fig. 1. Clays from the eastern Washington— Idaho clay area have been mined for more than 50 years. At present Mica, Washington deposits are used by the Gladding—McBean & Co. to make a variety of bricks and ceramic products and Latah County, Idaho clays are used by the A. P. Green Fire Brick Co. to make refractories. The Anaconda Co. made an intensive investigation of the clay deposits in the northeastern Washington-!daho area in 1919 to determine the existence of a supply of raw materials from which alumina could be made. The greater part of the work, which included systematic drilling and shaft sinking, was concentrated at Mica, Wash. This was part of a research project carrted on by the Anaconda Metallurgical Research Dept. under the direction of Frederick Laist and F. Frick and it was terminated in 4920. V. D. Perry, Vice President and Chief Geologist for The Anaconda Co., in 1952 assigned the writer to make a preliminary study of clay and other potential sources of alumina ore in the Pacific Northwest with particular emphasis on those deposits which might be of future importance to The Anaconda Co9s. then new aluminurri plant at Columbia Falls, Mont.

Jan 1, 1961

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By Robert Pack

INTRODUCTION SOONER or later in the development of any natural resource it becomes highly desirable to know the quantity of this resource in the country as a whole, as well as of the part that is being developed, for the general course and. conduct of the development work must be governed to some extent by the total supply available. An accurate estimate of the quantity of any natural resource is difficult to make; yet if one is diligent enough one can obtain a pretty accurate idea of the quantity of marketable timber, the acreage of tillable land, or the horsepower that may be developed from the streams, for these are things that may be measured. But any attempt to estimate the quantity of some mineral in the ground appears to enter the realm of imagination and it seems that the estimate can be nothing more than a blind guess. It may appear to be especially futile to attempt to determine the quantity of oil and gas that is available in the ground, for these minerals are so vagrant that even if the quantity now available should be known quite exactly, the quantity that will eventually be obtained may be much less, for certain losses in the extraction of both oil and gas are unavoidable, and just what these losses will be cannot be predicted. Though necessarily inaccurate, estimates of such mineral reserves are, however, of distinct value, for they summarize the existing knowledge of the deposits of the mineral and thus enable those who are interested in some industry that depends in one way or another on this mineral to formulate a rational commercial policy. Some time ago, when the price of gasoline suddenly rose in a rather spectacular manner, the writer was one of the U. S. Geological Survey geologists called upon to help to estimate the quantity of oil that could be obtained in the United States, for the fear had become widespread that perhaps the rate of increase in the price of gasoline was a measure of the rate of depletion of the supply of petroleum. It thus became his

Jan 8, 1917

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

Executive A R LEDOUX, Chairman ARTHUR S DWIGHT CHARLES F RAND E P MATHEWSON J V W REYNDERS Membership E DEGOLYER, Chairman W Y WESTERVELT, Vice-chairman WILLIAM H BASSETT H G MOULTON C MINOT WELD Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER Library GEORGE C STONE,' Chairman JOHN H JANEWAY ALEXANDER C HUMPHREYS, ROBERT LINTON FREDERICK F SHARPLESS

Jan 1, 1923